6. After your flash mix the water was sent to a clarification basin that was 24 feet in diameter and 20 feet tall. What was the detention time in hours of 0.43 MGD? 5.4 hours 4.3 hours 3.8 hours 2.3 hours After the water leaves your sedimentation basin, it is ready for filtration. Your two filters measure 10 feet in diameter. What is the filtration rate is gpm for your flow of 0.43 MGD? 19 gpm/sq/ft 29 gpm/sq/ft 39 gpm/sq/ft 49 gpm/sq/ft You have had a filtration breakthrough (failure) and have brought your old roughing filtration system on line. The old filter is 8 feet square and 4 feet deep. What is the filtration rate in gpm/sq/ft for your flow of 0.43 MGD? 10.33 gpm/sq/ft 8.55 gpm/sq/ft 5.99 gpm/sq/ft 4.66 gpm/sq/ft

6. After your flash mix the water was sent to a clarification basin that was 24 feet in diameter and 20 feet tall. What was the detention time in hours of 0.43 MGD? 5.4 hours 4.3 hours 3.8 hours 2.3 hours After the water leaves your sedimentation basin, it is ready for filtration. Your two filters measure 10 feet in diameter. What is the filtration rate is gpm for your flow of 0.43 MGD? 19 gpm/sq/ft 29 gpm/sq/ft 39 gpm/sq/ft 49 gpm/sq/ft You have had a filtration breakthrough (failure) and have brought your old roughing filtration system on line. The old filter is 8 feet square and 4 feet deep. What is the filtration rate in gpm/sq/ft for your flow of 0.43 MGD? 10.33 gpm/sq/ft 8.55 gpm/sq/ft 5.99 gpm/sq/ft 4.66 gpm/sq/ft

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

How to determine the needed surface area of the secondary clarifier tank given that the flow is 40,000 m3 per day and the recycling ratio is 0.5 . The necessary solids concentration in the underflow is 13,000 mg/L, while the Mixed liquor suspended solids concentration in the activated sludge is 4,500 mg/L. The table below shows the settling properties of sludge: Mixed liquor suspended solids Mg/l Settling velocity m/hr 2000 6 4000 3 6000 1 8000 0.2 10000 0.1 13000 0.1
Determine the Aeration Basin Dimensions for a town of 200,000 population. Mixed Liquor Suspended Solids is 3500 mg/L. The BOD Loading rate is 0.48 kg/ (?3 –day), Sludge Volume Index is 120 mL/g; Return sludge is 35%; the concentration of BOD is 0.093 Kg/(Capita –day). Primary sedimentation tank removes 35% of BOD.
The influent suspended solids concentration to a primary settling (clarifier) tank is 300 mg/L. The average flow rate is 0.037 m3/s. If the suspended solids removal efficiency is 65 percent, how many kilograms of suspended solids are removed in the primary settling tank each day?
Determine the total dissolved solids concentration using following data: i) Volume of filterable sample = 50 mL ii) Tare weight of the evaporating dish, W_{1} = 30.3419 iii) Weight of evaporating dish with dry solids, W_{2} = 30.3675g
A 50 mL of wastewater sample was brought to the lab and filtered out to measure the solids concentration. The weights of filter paper before, and after filtration (with solids) are 0.182 g and 0.197 g, respectively. The weights of aluminum cup tare before, and after dry (with solids on filter paper) are 100.08 g and 100.76 g, respectively. What is the total suspended solids concentration (TSS), in mg/L or grams/liter (or, other units)? Show your math-work.
How to determine the needed surface area of the secondary clarifier tank given that the flow is 40,000 m3 per day and the recycling ratio is 0.5 . The necessary solids concentration in the underflow is 13,000 mg/L, while the Mixed liquor suspended solids concentration in the activated sludge is 4,500 mg/L. Hint: Plot SFg= CiVi then Use SFL equation to get the area The table below shows the settling properties of sludge: Mixed liquor suspended solids Mg/l Settling velocity m/hr 2000 6 4000 3 6000 1 8000 0.2 10000 0.1 13000 0.1
3. A 100 mL of wastewater sample was drying on a 0.5 g empty dish weight at 104 °C to weight 0.5625 g. Another 100 mL of the same wastewater was first filtered and the filtrate was dried on a 0.5 g dish at 104 °C to weight 0.5325 g. Determine in mg/L the:a) TSb) TSSc) TDSd) VSS assuming it represents 70% of TSS
A one cell rapid sand filter tank has a loading rate 9.0 m/h, surface dimensions of 15*6 m. The sand and gravel depths are 70 cm and 60 cm respectively. The height of wash trough is 50 cm and the height of water above surface of sand is 2.0 m. Note that Shape factor of sand is 0.80 and stratified bed porosity is 0.50. a) What flow rate (m³/sec) does the filter handle during production? b) What is the total height of filter basin (m)? c) Calculate the head loss if the value of this term [2 (Co fid)] equal to 105700. d) In your opinion this filter tank specified the Saudi specifications?
The discharge of water collected from a constant head permeameter in a period of 15 minutes is 500 ml. The internal diameter of the permeameter is 5 cm and the measured difference in head between two gauging points 15 cm vertically apart is 40 cm. Calculate (a) the coefficient of permeability (mm/s), (b) If the dry weight of the 15-cm long sample is 4.86 N and the specific gravity of the solids is 2.65, calculate the seepage velocity (mm/s).
In rapid sand filters, the flow rate capacity is 0.3 m3/s and the filtration rate is 100 L/m2.min. When one filter is stopped the filtration rate become 150 L/m2.min. If each filter is backwashed for 5 mins and backwash rate is 60 m3/m2.hr. Find the number of filters, area of each filter, percentage of backwash water to filtered water if the filter is stopped 30 min/day. Also, find the diameter of the pipe which transport the backwash water if the designed velocity is 3m/s.
The design capacity of the waterworks is 0.30 m³/s. Design the number and size of filters and calculate normal filtration. 2. A sieve analysis curve of a typical filter sand gives dgo= 0.99mm and UC = 1.38. What are its d10 and deo?
For an activated sludge basin with a flow rate of 500 L/s if the influent BOD5 = 100 mg/L, the MLVSS = 3000 mg/L and the volume of the aeration basin = 766100 gallons Find the F/M ratio If the WAS X= 10000 mg/L, find the WAS flowrate (m3/d)