6. Blocks A and B have a mass of 3 kg and 9 kg, respectively, and are connected to the weightless links shown in the figure. Determine the largest vertical force P that can be applied at the pin C without causing any movement. The coefficient of static friction between the blocks and the contacting surfaces is µ, = 0.3. B 30

6. Blocks A and B have a mass of 3 kg and 9 kg, respectively, and are connected to the weightless links shown in the figure. Determine the largest vertical force P that can be applied at the pin C without causing any movement. The coefficient of static friction between the blocks and the contacting surfaces is µ, = 0.3. B 30

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter7: Dry Friction

Section: Chapter Questions

Problem 7.88RP: The panel of weight W with its center of gravity at G is placed between vertical guides and...

See similar textbooks

Similar questions

The two uniform sheets of plywood, each of length L and weight W, are propped as shown. If the coefficient of static friction is 0.5 at all three contact surfaces, determine whether the sheets will remain at rest.
The single-threaded screw of the floor jack has a pitch of 0.5 in. and a mean radius of 1.75 in. The angle of static friction is 8.5. (a) Determine the couple C that must be applied to the screw to start lifting a weight of 4000 lb. (b) What is the couple required to start lowering the weight?
The two homogeneous bars AB and BC are connected with a pin at B and placed between rough vertical walls. If the coefficient of static friction between each bar and the wall is 0.25, determine the largest angle 6 for which the assembly will remain at rest.
The panel of weight W with its center of gravity at G is placed between vertical guides and released. Determine the largest height h for which the panel will not slide down due to binding at corners A and B. The coefficient of static friction between the panel and the guides is 0.5.
The 40-lb spool is suspended from the hanger GA and rests against a vertical wall. The center of gravity of the spool is at G and the weight of the hanger is negligible. The wire wound around the hub of the spool is extracted by pulling its end with the force P. If the coefficient of static friction between the spool and the wall is 0.25, determine the smallest P that will extract the wire.
Find the largest value of b/h at which the folding table is in equilibrium. The coefficients of static friction are 0.5 at A and 0.3 at C. Neglect the weight of the table.
The screw of the clamp has a square thread of pitch 0.16 in. and a mean diameter of 0.6 in. The coefficient of static friction between the threads is 0.4. Determine (a) the torque C0 that must be applied to the screw in order to produce a 28-lb clamping force at A; and (b) the torque required to loosen the clamp.
The 60-lb plank rests on a frictionless roller at A, and the 20-lb triangular support BD. Both bodies are homogenous. The coefficients of static friction are 0.4 at B and 0.3 at D. Determine the largest force P that can be applied to the plank without initiating motion.
The 5.33-kg cylinder is suspended from two equal-length cords (L = 690 mm). The end of each cord is attached to a ring (negligible mass) as shown in the figure. The ring passes along a horizontal shaft. Provided that the rings can be separated by the greatest distance d = 352 mm and still support the cylinder, determine the coefficient of static friction between each ring and the shaft. The only answer is 0.264. Thanks.
Determine the force P required to move the wedge to the right if the coefficient of static friction is 0.35 at all contact surface (Figure 3). The uniform cylinder weight, W is 20 kN, and the weight of the wedge may be neglected.
The rope running over two fixed cylinders carries the 4-kg mass at one end. Determine the force P that must be applied to the other end to initiate motion. The coefficient of static friction between the rope and the cylinders is 0.15. BISECTION METHOD
The man is trying to push the homogeneous 20 kg ladder AB up a wall by applying the horizontal force P (Figure 4). Determine the height, h where the man should push the ladder so that he can move the ladder if the applied force, P is 200 N. The coefficient of static friction at all contacting surfaces is 0.3.