6. For a wing of aspect ratio AR, having an elliptical lift distribution, the induced drag coefficient is (where CL is the lift coefficient) CL (a) TAR CL (c) 2RAR (d) TAR2 TAR 7. Laminar flow airfoil is used to reduce the (a) pressure drag (b) induced drag (c) skin friction drag (d) wave drag 8. Set the aerofoil your chosen angle of incidence is .. gives a good installed pressure distribution. (a) twelve degree (b) ten degree (c) eight degree 9. The critical Mach number for a thick airfoil will be (a) lesser than a thin airfoil. (b) greater than a thin airfoil. (c) equal to a thin airfoil. (d) cannot be related to thin airfoil 10. What is the dimension for Lift coefficient? (a) N/s (b) kg/N (c) Dimensionless

6. For a wing of aspect ratio AR, having an elliptical lift distribution, the induced drag coefficient is (where CL is the lift coefficient) CL (a) TAR CL (c) 2RAR (d) TAR2 TAR 7. Laminar flow airfoil is used to reduce the (a) pressure drag (b) induced drag (c) skin friction drag (d) wave drag 8. Set the aerofoil your chosen angle of incidence is .. gives a good installed pressure distribution. (a) twelve degree (b) ten degree (c) eight degree 9. The critical Mach number for a thick airfoil will be (a) lesser than a thin airfoil. (b) greater than a thin airfoil. (c) equal to a thin airfoil. (d) cannot be related to thin airfoil 10. What is the dimension for Lift coefficient? (a) N/s (b) kg/N (c) Dimensionless

Principles of Heat Transfer (Activate Learning with these NEW titles from Engineering!)

8th Edition

ISBN:9781305387102

Author:Kreith, Frank; Manglik, Raj M.

Publisher:Kreith, Frank; Manglik, Raj M.

Chapter5: Analysis Of Convection Heat Transfer

Section: Chapter Questions

Problem 5.49P

See similar textbooks

Similar questions

Engine oil at 100C flows over and parallel to a flat surface at a velocity of 3 m/s. Calculate the thickness of the hydrodynamic boundary layer at a distance 0.3 m from the leading edge of the surface.
Air at 1000C flows at an inlet velocity of 2 m/s between two parallel flat plates spaced 1 cm apart. Estimate the distance from the entrance to the point where the boundary layers meet.
What is the Effect of wing plan form (taper ratio and wing twist) and aspect ratio(AR) on the Induced drag coefficient, ?
Consider the NACA 2412 airfoil, data for which is given in 4.10 and 4.11. The data are given for two values of the Reynolds number based on chord length. For the case where Rec = 3.1×106, estimate: (a) the laminar boundary layer thickness at the trailing edge for a chord length of 1.5 m and (b) the net laminar skin-friction drag coefficient for the airfoil.
a)What is the impact of increasing Reynolds number on skin friction and pressure drags over an airfoil? What can be happened for separation in this case? b) What is an adverse pressure gradient and where does it occur on an airfoil (show that on a sketch)? c) Why lift-to-drag ratio is an important parameter for an aircraft? d)How can changing in altitude affect the aircraft power required, PR? Show thatmathematically and graphically?
The measured lift slope for the NACA 23012 airfoil is 0.1080 degree−1,and αL=0 = −1.3◦. Consider a finite wing using this airfoil, with AR = 8and taper ratio = 0.8. Assume that δ = τ . Calculate the lift and induceddrag coefficients for this wing at a geometric angle of attack = 7◦.
Consider a finite wing with an aspect ratio of 3. Assume an elliptical liftdistribution. The lift slope for the airfoil section is 0.1/degree. Calculateand compare the lift slopes for (a) a straight wing, and (b) a swept wing,with a half-chord line sweep of 45 degrees.
For a 10 deg included angle wedge at 0 deg AOA, calculate the lift and drag coefficient (Cl = 0, Cd = 0.082). Then calculate the lift and drag at AOA=4 deg (Cl = 0.16, Cd = 0.093). Let M=2.
The airfoil section of the wing of the British Spitfire of World War II fame is an NACA 2213 at the wing root, tapering to an NACA 2205 at the wing tip. The root chord is 8.33 ft. The measured profile drag coefficient of the NACA 2213 airfoil is 0.006 at a Reynolds number of 9 × 106. Consider the Spitfire cruising at an altitude of 19000 ft. Assume that μ varies as the square root of temperature. At this velocity and altitude, assuming completely turbulent flow, estimate the skin-friction drag coefficient for the NACA 2213 airfoil, and compare this with the total profile drag coefficient. Calculate the percentage of the profile drag coefficient that is due to pressure drag. (Round the final answer to three decimal places.) The skin-friction drag coefficient for the NACA 2213 airfoil is .
A Mitsubishi A6M Zero which has a wing area of 22.44 square meters with a lift generated of 6,000 N. If the wingspan is 12 meters, Calculate the velocity at minimum thrust required at standard sea level conditions. Assume wing is an elliptical planform and parasite drag is 0.045.
Read the question carefully and give me right solutions with clear calculations. The air flows past a 1m diameter disk oriented normal to upstream flow at 6.8m/s. The pressure distribution on front of the disk is function of the radius, where p(r) = (25 − 100 r2 ) N/m2 , and the pressure acts uniformly on back side with suction pressure of pback = −22 P a. a. Determine the total drag force on the disk. b. Calculate the drag coefficient for the disk . (Density = 1.25 kg/m3 ).
Kindly give me both right solutions with clear calculations The drag polar of a glider is given by CD=0.01+0.022CL2 . If it is launched from a height of 400m in still air. Please determine:(a) the maximum lift to drag ratio ??;(b) the greatest possible ground distance it can cover.