6. The following data refers to a vertical block resonance test carried out on a 1.5 m × 0.75 m × 0.7 m high (M150) concrete block. f (cps) 15 18 20 22 23 24 26 27 29 Amp. (mm) 0.03 0.05 0.08 0.15 0.2 0.22 0.18 0.16 0.13 Plot frequency vs. amplitude and compute coefficient of elastic uniform compression Cu and damping factor of the soil at site.

6. The following data refers to a vertical block resonance test carried out on a 1.5 m × 0.75 m × 0.7 m high (M150) concrete block. f (cps) 15 18 20 22 23 24 26 27 29 Amp. (mm) 0.03 0.05 0.08 0.15 0.2 0.22 0.18 0.16 0.13 Plot frequency vs. amplitude and compute coefficient of elastic uniform compression Cu and damping factor of the soil at site.

Fundamentals of Geotechnical Engineering (MindTap Course List)

5th Edition

ISBN:9781305635180

Author:Braja M. Das, Nagaratnam Sivakugan

Publisher:Braja M. Das, Nagaratnam Sivakugan

Chapter10: Shear Strength Of Soil

Section: Chapter Questions

Problem 10.24CTP

See similar textbooks

Similar questions

After the sample has been fractured and reassembled, the gage marks that initially measured 2.000” now measure 2.050”. What is the percent elongation for the sample (provide answer as %, i.e. list 15% as 15, not 0.15)?
A calibration test of a 2.5cm circular sharp edged orifice in the vertical side of the large tank showed a discahrge of 590 N of water collected in 81 seconds, when under a constant head of 4.70 m. In addition, measuremnt of the trajectory of the jet gave the following data: A point on the jet has the coordinates in cm (235, -30), with the orifice located at the origin of the rectangular coordinate system. Find the value of Cd, Cc, and Cv, Show a Diagram
The answer should be in Nm. thanks.. will upvote
A calibration test of a 2.5cm circular sharp edged orifice in the vertical side of the large tank showed a discahrge of 590 N of water collected in 81 seconds, when under a constant head of 4.70 m. In addition, measuremnt of the trajectory of the jet gave the following data: A point on the jet has the coordinates in cm (235, -30), with the orifice located at the origin of the rectangular coordinate system. Find the value of Cd. Include FBD. a. 0.629 b. 0.989 c. 0.98 d. 0.636
A calibration test of a 2.5cm circular sharp edged orifice in the vertical side of the large tank showed a discahrge of 590 N of water collected in 81 seconds, when under a constant head of 4.70 m. In addition, measuremnt of the trajectory of the jet gave the following data: A point on the jet has the coordinates in cm (235, -30), with the orifice located at the origin of the rectangular coordinate system. Find the value of Cc.CHOICES a.0.629 b.0.989 c.0.98 d.0.636
The measured length during taping are 545.80m and 546.1m. Determine the relative precision.
The surveying team used 30 m tape in measuring an inclined distance. The measured length on the slope was recorded to be 459.20m long. The difference in elevation between the initial point and the end point was found to be 1.25m. The 30 m tape is of standard length at a temperature of 10°C and a pull of 50N. During measurement the temperature reading was 15°C and tape was supported at both ends with an applied pull of 75 N. The cross-sectional area of the tape is 6.50 mm² and the modulus of elasticity is 200 GPa. The tape has a mass of 0.0075 kg/m. Determine the true horizontal distance. K=0.0000116 m/°C
Which phreatic line is most likely to be observed during a pumping well test? Provide your justification with reasons.
is this correct? interpolate. Specimen No. Time (second) Penetration (mm) 1. 30 40 180 38 800 34 1200 30 2000 22 30000 2 35000 none Initial Set: __________ seconds
Q.4 For a compound differential manometer in fig given below calculate (PA-PB)?
Jisoo used a 40 meter steel tape in measuring an inclined distance on a gentle slope. The sloping distance was recorded to be 440 meters long. The difference in elevation between the initial point and the end point was found to be 32.49 m. The 40-meter tape is of standard length at a temperature of 20 °C and a pull of 34 N. During measurement, the temperature reading was 44 °C and the tape was supported throughout its length with an applied pull of 82 N. The cross-sectional area of the tape is 1.54 mm^2 and the modulus of elasticity is 200 GPa. The tape has a mass of 0.68 kg. Determine the corrected horizontal distance in meters. Round off to two decimal places.
Deformation Dial reading Load Dail reading 0 20 40 60 12 80 19 100 21 120 2 140 26 160 30 180 33 200 35 220 38 240 a2 260 46 280 50 300 54 320 58 340 62 360 66 380 70 400 75 420 80 440 85 260 90 480 95 500 100 520 110 540 115 560 120 580 125 600 130 620 135 640 140 660 145 700 150 720 150 740 150 Do Unconfined compressive test calculation And stess-strain curve and mohr’s circle If Unconfined compressive strength / Data Sheet abrove Sample data: D= 7.29 cm L=14.78cm Deformation dial: 0.1mm Load dial: 0.3154 Ib Use KN for load and KPa for stress