6. The switch in the circuit below has been open for a long time before it closes at t = 0. Obtain an equation for the inductor current i, (t), t≥ 0. Note: Sometimes it may not be clear whether a circuit is series RLC or parallel RLC. To find the characteristic equation for t≥ 0, deactivate all sources and examine the resulting circuit. Once you identify it as a series or parallel RLC, use the corresponding characteristic equation. 120 mA Fo 31.25 mH 1500 300 0.5 F 3V

6. The switch in the circuit below has been open for a long time before it closes at t = 0. Obtain an equation for the inductor current i, (t), t≥ 0. Note: Sometimes it may not be clear whether a circuit is series RLC or parallel RLC. To find the characteristic equation for t≥ 0, deactivate all sources and examine the resulting circuit. Once you identify it as a series or parallel RLC, use the corresponding characteristic equation. 120 mA Fo 31.25 mH 1500 300 0.5 F 3V

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

In the circuit , the resistor isadjusted for critical damping. The initial capacitor voltage is 20 V, andthe initial inductor current is 30 mA.1. Find the numerical value of R.2. Find the numerical values of i and di/dt immediately after theswitch is closed.3. Find vC(t) for t≥0.
1) The circuit shown below is initially, for t < 0, with capacitor C connected to a battery (Vbat = 12 V).The key is switched at t = 0, disconnecting the battery and turning on the capacitor to the rest of the circuit.a)Calculate the circuit current in the time domain, i(t).b) In practice, after how long can the energy stored in the circuit be considered to be irrelevant (close to zero)?
The switch in the circuit shown in the figure below has been open for a long time. It closes at t = 0s, then 1-Calculate the initial stored energy in the capacitor 2- Find the current iR(t) for t >= 0. 3- Plot the current iR(t) for t >= 0.
The switch in the circuit shown has been closed for a long time and is opened at t=0. Find:a.) v at time t= 0^-b.) v at time t=0^+c.) the time constant for t>0e.) the initial energy stored in the capacitorf.) the length of time required to dissipate 50% of the initially stored energy. please help me, and please show the complete solution so that I will understand the process.
*The resistance, inductance, and capacitance in a parallel RLC circuit are 1900 Ω , 250 mH , and 9 nF , respectively. * Pt A. Calculate the minimum root of the characteristic equation that describes the voltage response of the circuit. Pt B. Calculate the maximum root of the characteristic equation that describes the voltage response of the circuit. Pt C.Will the response be over-, under-, or critically damped? Pt D. What value of R will yield a damped frequency of 12 krad/s? Pt E. What are the roots of the characteristic equation for the value of R found in Part D? Pt F. What value of R will result in a critically damped response?
A RL circuit has an emf of 5 volts, a resistance of 50 ohms, an inductance of 1 henry, and no initial current. Find (a) the current in the circuit at any time t and (b) its steady-state component.
The switch in the circuit shown in the following figure has been in position 'B' for a long time. At t=0, it moves to position 'A'. Using differential equation, find VC(t) for t≥0. a. Write a differential equation in VC(t) b. Find α and ω0
The initial voltage across the capacitor at t = 0 in the circuit shown is 2V. Voltage Vs is applied at t = 0; that is, Vs = 10 u(t) V. Find voltage v(t), t >= 0, across the capacitor.
For the electric circuit shown, the switch has been closedfor a long time before it opens at t = 0. Find the mathematicalexpression for the capacitor voltage vC(t) for t > 0
After the switch in the circuit given below is kept closed for a long enough time, it opens at t=0 s. Since they are defined as R = 1 Ω and Vs = 2 volts in the circuit; What is the value (vc(6)) of the voltage across the capacitor at t=6 s? NOTE: Please enter your answer as 2 digits after the comma.
In the circuit, the resistor is adjusted for critical damping. The initial capacitorvoltage is 15V , and the initial inductor current is 6 mAa) Find the numerical value for Rb) Find the numerical values of i and di ⁄ dt immediately after the switch is closedc) Find vc(t) for t bigger than or equal to 0
The uncharged capacitor in the circuit is initially switchedto terminal a of the three-position switch. At t=0, the switch is moved toposition b, where it remains for 15 ms. After the 15 ms delay, the switch ismoved to position c, where it remains indefinitely. 1. Derive the numerical expression for the voltage across the capacitor.