6. What is the function of resistance 3302? Explain . 7. What is the Zener breakdown, and how it differs from the electrical breakdown? 8. How do you explain the stability of o/p voltage in spite of /p voltage changing? 9. Calculate the V, in the circuit Fig(3), when Vin=50v -6- 680 2 330 2 Vin 15v V=10v R. TL Fig. (3)

6. What is the function of resistance 3302? Explain . 7. What is the Zener breakdown, and how it differs from the electrical breakdown? 8. How do you explain the stability of o/p voltage in spite of /p voltage changing? 9. Calculate the V, in the circuit Fig(3), when Vin=50v -6- 680 2 330 2 Vin 15v V=10v R. TL Fig. (3)

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

3: What is the ampacity of 10 AWG R90 when installed in a walk-in freezer that has an ambient temperature of -56oC?
Ex. 1628. Vcc=12VDC, Rcoil=156 Ohms in Fig 1628. Find Ice (amps) and Vce (volts), for the Barker transistor model: Ice=0.052000(1-exp(-Vce/2) amps. ans:2
Sketch vo for each network and explain your solution.
Refer to the transistorized circuit. Keep in mind that although you do not know the current-voltage relationship of the device, it still complies with the LCK and the LVK. (a) If Id = 1.5 mA, calculate Vds. (b) If Id = 2 mA and Vg = 3 V, calculate Vgs.
It is desired to obtain the Thevenin equivalent of a non-ideal battery. When no load is connected, the terminal voltage of the battery (that is, the voltage across nodes a and b) is measured to be 12.4 volts. When a 30-watt load is connected, the terminal voltage of the battery drops to 12 volts. a. What is the Thevenin voltage of the Thevenin equivalent for this battery? b. What is the Thevenin resistance of the Thevenin equivalent for this battery?c. A load is connected to source network. At the terminals of the source to which the load is connected, Vth=120 volts and Rth=10 ohms. What should be the resistance of the load so that it will draw the maximum power possible from the source network?
Companies designs, creates, and sells Integrated Circuits (chips). What do your buyers useto compare your IC products against your competition’s? Give 3 types of IC benchmarkmeasurements in short answer
Electrical Engineering 1. What voltage(s) should you provide when you power the Arduino through the barrel jack? How much current can be made available to the Arduino through this port? Does this port have any protection on it? 2. When you are powering the board using the barrel jack, what does the Vin pin do? 3. When you are powering the board using one of the ports mentioned above, how much current can you draw from the 5V pin? What about the 3.3V pin? What about a regular I/O (digital or analog) pin? 4. What voltage(s) should you provide when you power the Arduino through the Vin pin? How much current can be made available to the Arduino through this pin? Does this port have any protection on it? 5. What voltage(s) should you provide when you power the Arduino through the 5V pin? How much current can be made available to the Arduino through this pin? Does this port have any protection on it? 6. How much power does a normal 9V battery contain? How long could you run an Arduino board…
Determine VO for each network of the given figure, for the input shown. Show (upload) your solution.
For a particular thermocouple, if one junction is maintained at 0˚C (cold junction) and the other junction is used as a probe to measure the desired Celsius temperature t, the voltage generated in the circuit related to the temperature t as ϵ = r(a + bt). Further, for this thermocouple, when ϵ is, in millivolts, the two constants are a=0.25, b=-5.5x10^-4. (a) What are the units of a, b? (b) Determine the value of for each of the measured temperatures -100°C, 100°C,200°C, 300'C, 400°C and plot an Et-curve.
Vbe=0.7v hFE=173.21 find vb,ve,ie,ib,icq,vceq
it is desired to obtain the Thevenin equivalent of a non-ideal battery. When no load is connected, the terminal voltage of the battery (that is, the voltage across nodes a and b) is measured to be 12.4 volts. When a 30-watt load is connected, the terminal voltage of the battery drops to 12 volts. 1. What is the Thevenin resistance of the Thevenin equivalent for this battery? 2. A load is connected to source network. At the terminals of the source to which the load is connected, Vth=120 volts and Rth=10 ohms. What should be the resistance of the load so that it will draw the maximum power possible from the source network? a. 110 ohms b. 10 ohms c. 1440 ohms d. 0 ohms e. 12 ohms
In Dhaka city during the month of May, a 20W rated solar panel supplies 15W of power at an output voltage of 15V & an output current of 1A. But during the month of December, the same solar panel supplies 8.5W of power at an output voltage of 10.5V & an output current of 0.81A.The solar panel is used to charge a 12V battery. Practically, for charging a 12V battery we need to supply 13V. i) In the month of May, the user will need a DC-DC converter (Buck) to charge the battery.a) What will be the duty cycle?b) Assuming that the converter is 100% efficient, what will be the input current to the battery?