Please help me with the following question.Please put the whole process and solution because I’m having a difficulty with understanding it. Thank you very much. The 66-kN point load in this figure below carries a floor DE, which in turn is simply supported at its ends by floor beams. These beams transmit their loads to the simply supported girder AB. Determine the internal shear and moment acting at point C in the girder.   Subject: Structural Theory

Q: * .R.L. is same as B.M False O True O we can measure the horizontal distance between the Level instr...

A: We have to determine the given statement in the question is either false or true as per the knowledg...

Q: Take your tinme on answering  given: a.3.7 (m) b.10 (kN/m) c.17.5 (kN)

A:

Q: 4. Determine the maximum and the minimum values of weight W which may be applied without causing the...

A:

Q: 6. The shear-force diagram for a beam is shown in the figure. Assuming that no couples act as loads ...

A:

Q: 3. Relative to an orthonormal basis, the components of a symmetric tensor R are such that -R, =R33 ;...

A: Ans: Principal value of R= 0, 1, -1. 

Q: A triangular lamina with base 3 m and height 3 m is immersed in water vertically with base parallel ...

A: Given:- The base of the triangular lamina = 3 m The height of the triangular lamina = 3 m The triang...

Q: A cylinder vessel filled with water with a 2m diameter and 5m high. It was rotated with uniform angu...

A:

Q: kPa. The bottom of the footing is situated 1 m below the ground surface. Assume the average unit wei...

A: Given : 400 mm X 400 mm column Soil bearing capacity = 250 kN/m2 fc = 21 MPa, fy = 414 MPa

Q: Problem 2. Shear at point B 20 kN/m -5 m- 10 m- 33.33kN O 43.33kN 53.33kN 23.33kN

A:

Q: a KN/m b KN 2.4 m A 21 31 |41 31 51 b KN a KN/m 3.6 m F| 21 31 41 31 51 G H em em d m

A:

Q: If a liming recommendation for 5-hectare field calls for 30 tons of CaCO3, how much of a liming mate...

A: RNP stands for relative neutralizing power  RNP value of lime indicates the percentage of effectiven...

Q: Calculate the coordinates of a foresight point P101 using the following data: Occupied point O: N 21...

A: Point O BS=0.45 m HI=144 m FS=- Elevation=143.55 m Azimuth=285 degree Distance=35.3 m Point A BS=- H...

Q: Perfectly Plastic Yielding Rank the curves based on the total amount of yielding in the perfectly p...

A: To rank the given stress-strain curves based upon the amount of yielding in the perfectly plastic re...

Q: . Determine the vertical deflection @ pt. C and slope @ pt. B. E = 200 GPa and moment of the cross-s...

A: ###CALCULATIONS of deflection at C and Slope At B####

Q: A truck carrying fully-filled water container that is 2.5m long, 2.5m wide, and 2m high. The entire ...

A:

Q: The following T-Beam has given properties: Effective Depth (d) = 485 mm, thickness of the slab = 100...

A: Given in the Question: Thickness of web = bw = 300mm Effective span = L = 5M Live load  = Wll = 163k...

Q: ha4.7%gradeatStation50+00.00andan elevation of PVI of 532.20 ft. To provide proper cover for a culve...

A: PVCSta=PVIsta-L2=5000-L2PVCelv=PVIelv-g2L2=532.2--0.033L2Equation of the curve:y=g2-g12Lx2+g1x+PVCel...

Q: Consider a cylinder of specific gravity SG < 1 floating vertically in water (SG = 1), as in the figu...

A: Derive a formula for the stable values of D/L as a function of SG and apply it to the case D / L = 1...

Q: A "hawser" is wrapped around a fixed "capstan" to secure a ship for docking. If the tension in the r...

A: This is the problem based on belt friction. The force decreased exponentially with

Q: Calculate the quantity (cubic meter) of the concrete used in a pier of 1.2m diameter and 6m length. ...

A: Given- diameter of pier=1.2 mlength of pier=6mreinforcement details=8 bars @ 256 mm diameter    

Q: For all problems, draw the indicated influence lines. For #1, use both the "unit load method" and th...

A:

Q: Consider a cylinder of specific gravity SG < 1 floating vertically in water (SG = 1), as in the figu...

A:

Q: PROBLEM 2. The maximum stress that causes the failur of a cohesive soil specimen in a tri-axial test...

A: Tri - axial test  σ1 = Major Principle stress = σ3 + σd σd = deviator stress σ3 = Confining Pressure...

Q: 47 КРа 4Z KPa 28 KPa 2Y kPa D A 8X КРа 81 КРа 706 F B E For the state of stress as shown in Figure. ...

A:

Q: 1. Determine the horizontal and vertical components of force acting on radial gate ABC in the figure...

A:

Q: .5 Prepare a set of profile leveling notes for the survey in Figure 2-34. In addition to comput- ing...

A: QUESTION BEING ASKED HERE IS TO CHECK THE LEVELLING DATA. Hence , as we know that HEIGHT OF INSTRUME...

Q: 47 КРа 4Z KPa 28 KPa 2Y kPa D A 8X КРа 81 КРа 706 F B E For the state of stress as shown in Figure. ...

A:

Q: 5 pie 10 pie A 15 pie G K 80* 100* 120k 6 por 30 pie 180 pie- %3D

A:

Q: The volume flow rate of a given fluid is 0.002 m/sec. What is the mass flow rate of that fluid havin...

A:

Q: 1. Calculate the minimum wall thickness for a cylindrical vessel. The diameter of the vessel is 8.5 ...

A:

Q: It is found in a water sample that it has insufficient alkalinity and therefore soda ash (Na2CO3) is...

A:

Q: Determine the maximum speed that the cars of the roller-coaster can reach along the circular portion...

A: Using the formula for normal acceleration. The limiting value of velocity can be calculated

Q: The stiffness matrix for the given coordinates of the beam as shown in the figure is

A:

Q: A truck carrying fully-filled water container that is 2.5m long, .5m wide, and 2m high. The entire m...

A:

Q: Show complete solution and 3 decimal places for the final answer. Asap thanks!  A truck carrying fu...

A:

Q: |Moving Unit Load (1 kN) Al В C DE 5 m 7 m 4 m 2 m

A:

Q: has r2 = 22.5 cm, b2 = 5 c nd rotates at 1060 r/min. If 5 m, determine neoretical (a) flow rate and ...

A:

Q: etermine (a) the maximum bending stress and (b) the maximum shearing stress due to V in the simply s...

A:

Q: A doubly reinforced beam, which have a base of 310 mm, and an effective depth of 410 mm, is reinforc...

A:

Q: Create a Schematic diagram .autocad pls screenshot of Schematic diagram

A: To prepare the given engineering drawing in AutoCAD.   We will be using the following tools to make ...

Q: The stratification of different layers of soils is shown in the figure below along with their coeffi...

A:

Q: .5 Prepare a set of profile leveling notes for the survey in Figure 2-34. In addition to comput- ing...

A:

Q: A cube container with a dimension of 3m on each side is 60% full of water (density=1000kg/m³). The c...

A: Assuming the empty container to be weightless as no data is given.

Q: Determine the magnitude of the resultant force in kilonewton. F1 = 1,212 N F2 = 1,240 N F3 = 792 N 0...

A:

Q: A doubly reinforced beam, which have a base of 310 mm, and an effective depth of 410 mm, is reinforc...

A: To Determine Value of Moment Capacity, Mu

Q: 4:) A TRAPEZO1AL CHANNEL WITH SUES INCLINED 30° WITH THE HORI ZOTTAL AND A 5-25 m BOTTB WITHO IS LAD...

A:

Q: The possible direction of sway of the rigid frame shown in figure 10 kN C 1 m 4 m 1 m (21) 6 m (21) ...

A: Stiffness of member AC is KAC ={4E(2I)}/L =(8EI)/6 =1.333EI Stiffness of member BD is KBD ={3E(2I)}\...

Q: most important document/s in a bid? Why?

A:

Q: A car travelling 60kph is followed by another travelling 80kph. The lead car suddenly brakes to a st...

A:

Q: , then relation between A and B is: *

A:

Beams

In structural engineering, a beam is a component made of a variety of materials (including steel alloys, and wood) that can resist loads applied laterally to the beam axis. Members, elements, rafters, shafts, and purlins are all terms used to describe beams.