7: A cement factory has two lines. Each line is operating separately. If the production properties (average and standard deviation of compressive strength) are as shown in table below: 1) determine the best line, 2) find the 95% confidence interval for the variance and standard deviation if the variance is two time than the variance given (assume n = 15 for both lines).

7: A cement factory has two lines. Each line is operating separately. If the production properties (average and standard deviation of compressive strength) are as shown in table below: 1) determine the best line, 2) find the 95% confidence interval for the variance and standard deviation if the variance is two time than the variance given (assume n = 15 for both lines).

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

An operator is analyzing the structural strength of a cement mix. Structural strength is normally distributed σ2 = 1000 (psi)2 . What sample size is required if it is desired to estimate the structural strength with an an error less than 10 psi at 95% confidence level? Would the sample size increase or decrease if the confidence level become 90%. Have solutione. Sample size required at 95% confidence level is 154f. Sample size required at 95% confidence level is 39, reducing the confidence level to 90% decreases the sample sizeg. Noneh. Sample size required at 95% confidence level is at 39 %. reducing the confidence level to 90% will increase the sample sizes for the error to be less than 10
W o No. Load Elongation Lo P(KN) SL(mm) |(mm) Area O eng (KN/m²) Еeng (mm) m² 1 100 36.1 2 38 0.02 100 36.1 3 76.2 0.12 100 36.1 4 92.7 0.25 100 36.1 107 0.50 100 36.1 6. 149 2.03 100 36.1 7 160.6 3.55 100 36.1 8 102 3.87 100 36.1 9 100.7 4.01 100 36.1 10 98.33 4.12 100 36.1 11 155 4.65 100 36.1 12 142 5.1 100 36.1 13 124.2 5.84 100 36.1
A certain type of thread is manufactured with a mean tensile strength of 78.3 kilograms and a standard deviation of 5.6 kilograms. How is the variance of the sample mean changed when the sample size is: please show complete solution
Q.2. The mean and the standard deviation of the breaking load in experiments performed on 25 concrete columns are found as 10000 kg and 500 kg, respectively. Find the confidence interval of the mean at P=90%. Use the asymptotic sampling distribution. Use the exact sampling distribution. а) b)
Procedure: 1. Compression tests on specimens shall be made as soon as practicable after removal from the moist storage. A 28-day test shall be performed within +-20 hours of the 28thday. Test specimens shall be kept moist by any convenient method during the period between removals from moist storage and testing. They shall be tested in moist condition. 2. All test specimens for a given test age shall be broken within the permissible time tolerance prescribed below. TEST AGE PERMISSIBLE TOLERANCE 24 HOURS +-0.5 HOURS OR 2.1% 3 DAYS 2 HOURS OR 2.8% 7 DAYS 6 HOURS OR 3.6% 28 DAYS 20 HOURS OR 3.0% 90 DAYS 2 DAYS OR 2.2 % 3. With a clean rag or rush clean the bearing faces of the bearing blocks, test the specimens and exclusion controller (elastomeric cps). 4. Rest the specimen on the lower extrusion controller, place the top extrusion controller on the specimen, and check the spacing between the sides of the specimen and the extrusion controllers to ensure no contact between the cylinder…
Q5: A/A tensile test was conducted for a sample and the relationship between stress and strain was as shown in the following figure: Stress Strain the point (44*7)) and emotion) 1 6.67 Mpa 0.00067 2 13.3 Mpa 0.00133 3 20 Mpa 0.002 4 24 Mpa 0.003 strain S 22 Mpa 0.0035 Answer the following: 1- Calculate the modulus of elasticity. 2- Calculate the modulus of resilience. 3- The modulus of toughness is: 0.1Mpa -> 0.01 Mpa 0.001 Mpa 0.0001 Mpa - 4- Calculate the percentage of elongation. 5-Waisting occurs between the two points.......... and 6- Strain hardening occurs between the two points...... ..........3 *******
A sample of 15 concrete cylinders was taken randomly from the production of a plant. The strength of each specimen was determined, giving a sample standard deviation of 215 kN/m2 . Find the 95% confidence interval (with equal probabilities in the two tails) for standard deviation of the strengths. Assume the strengths follow a normal distribution.
Consider a 1,000-mm long, 25-mm diameter sample subjected to a tension test. Automatic high-precision gages recorded that for an applied load of 150 kN, the sample experienced a longitudinal strain of 2×10−3mm/mm. Assuming that the material remained elastic while loaded, determine its modulus of elasticity. A. 175.0 GPa B. 63.7 GPa C. 152.8 GPa D. 72.9 GPa Which of the following occurs when the value of Poisson’s ratio is doubled and the modulus of elasticity is kept constant? a. The lateral deformations experienced by the material is halved b. The volume of the material will remain constant when subjected to external forces c. The elastic region of the shear stress-strain diagram would be less steep d. The material can withstand higher amounts of stress before permanent deformations occur
Part A The data below shows the laboratory data for a fluid obtained using a viscometer at 20°C and 1 atm. -du/dy (sʻ1) T (Pa) 25 62.3 50 81.9 100 106.4 a) stress and shear rate. Use the data and the power law to determine the relationship between shear b) Use this relationship to estimate the shear stress at a shear rate of 40 s1. c) What is the apparent viscosity at a shear rate of 40 s1?
SHOW COMPLETE SOLUTION PLS VALUES: Y = 53 A = 1 B = 5
CLO 1: A rigid beam rests on two bronze bars 700 mm long. Another aluminum bar is placed between them which is 699.93 mm long. If the allowable stresses are Salum = 90 MPa and Sbronze = 80 MPa, find the maximum weight of the beam that the system can support (in KN). Note: please help us in this sample problem
Following experimental data are obtained from tensile test of a rectangular test specimen with original thickness of 2,5 mm, gauge width of 24 mm and gauge length of 101 mm: Load (N) Elongation (mm) 0 0 24372 0,183 23008 0,315 28357 5,777 35517 12,315 27555 17,978 23750 23,865 Based on the information above; draw stress-strain diagram of the material and answer the following questions. 1-)-Determine the modulus of resilience (in N.mm/mm3) of the material. (Use at least five decimal units) 2-)- Determine the elastic energy absorption capacity (in N.mm) of that specimen. 3-)Determine the plastic energy absorption capacity (in N.mm) of that specimen.