7) The following tensile load-length data were obtained for a metal rod of 0.505 cm diameter. Complete the table and plot the stress-strain curve. Note: Please show all data points on the curve Load (kN) Length (mm) Stress (MPa) Strain 50.000 20 50.103 40 50.198 50 50.258 60 50.285 65 50.355 70 50.505 80 51.258

7) The following tensile load-length data were obtained for a metal rod of 0.505 cm diameter. Complete the table and plot the stress-strain curve. Note: Please show all data points on the curve Load (kN) Length (mm) Stress (MPa) Strain 50.000 20 50.103 40 50.198 50 50.258 60 50.285 65 50.355 70 50.505 80 51.258

Principles of Geotechnical Engineering (MindTap Course List)

9th Edition

ISBN:9781305970939

Author:Braja M. Das, Khaled Sobhan

Publisher:Braja M. Das, Khaled Sobhan

Chapter10: Stresses In A Soil Mass

Section: Chapter Questions

Problem 10.12P: Refer to Figure 10.43. A strip load of q = 1450 lb/ft2 is applied over a width with B = 48 ft....

See similar textbooks

Similar questions

I want Normal stress developed in segment AB. A homogeneous bar with a cross-sectional area of 400 mm2 is attached to fixed supports as shown inthe figure. It is subjected to lateral forces P1 = 20 kN and P2 = 50 kN. Determine the normal stressdeveloped in segments AB and BC. Answer: σAB = 80.55 MPa
Given the following data from direct shear tests: Test Unit Weight Stress 1 13 17.5 2 26 22.4 3 39 26.2 4 52 31.0 Calculate the value of c and the angle.
Given the state of plane stress shown in the figure, compute the normal stress acting on a plane that is rotated 20 degrees counterclockwise from the y axis in kPa. Round to the nearest whole number and use the format 1234.
Solve the problems below : (Use 4 decimal places for all your computations ) 1. A water tank 3 m in diameter and 6 m high is made from a steel with thickness of 12 mm. a) When the tank is filled with water, determine the circumferential stress. b) Determine the longitudinal stress at the bottom of the tank when it is filled with water. c) If the tangential stress is limited to 5 MPa, what is the maximum height of water to which the tank may be filled.
Refer to Figure 10.43. A strip load of q = 1450 lb/ft2 is applied over a width with B = 48 ft. Determine the increase in vertical stress at point A located z = 21 ft below the surface. Given x = 28.8 ft. Figure 10.43
A moment is exerted on the profile given in the figure to make an angle B with the vertical. Calculate the stress at point B. Given a = 90 mm, b = 60 mm, c = 110 mm, d = 130 mm, Beta = 80 degrees, M = 13 kNm,
If P = 27 kN and if the diameter of rod 1 is 16 mm and the diameter of rod 2 is 12 mm, determine the axial normal stress in each rod in kilopascals. Note: Draw the Free Body Diagram, include the units/dimensions, use the proper formula and round-off all the answers and final answers to 3 decimal places.
Q1)The magnitude of stresses have been applied on soil element where Normal vertical stress is 120 KN/m² , Normal horizontal stress is 300 KN/ m², shear stress is 40 KN/m² and Angle of internal friction is 20°. Find the Principle stress and Normal and Shear stress on plan AB, figure 1. The figure 1 is below i have attached in jpg format. Solve the question according to this figure?
The stresses shown act at a point in a stressed body. The stress magnitudes are Sx = 60 MPa and Sy = 245 MPa, acting in the directions indicated in the figure. Using the equilibrium equation approach, determine the normal and shear stresses at this point on the inclined plane shown. Assume β = 53°.
The stresses shown act at a point in a stressed body. The stress magnitudes are Sx = 85 MPa and S, =- 200 MPa, acting in the directions indicated in the figure. Using the equilibrium equation approach, determine the normal and shear stresses at this point on the inclined plane shown. Assume B= 48°
a simply supported beam is carrying a varying load and a uniform load as shown in the figure. If the beam properties are given below, what is the final stress at bottom of beam section at a distance 2.47m from the right support where the totall losses of the prestressing force is 24% mpa beam wid=217mm height= 480mm varying load= 9.67kn/m uniform load = 4.27 kn/m x = 3.32 y = 5.95 Prestressing force = 429kn eccentricity = 95mm
Find the largest bending moment of M that the beam, whose cross section is shown in the figure, can safely carry. Draw a Stress diagram. (σç,em=3,5 kN/cm2 ; σb,em=8,5 kN/cm2 ). Note: for all odd values, two digits will be taken after the point.