7. The wheel loads on a small tractor crossing a 10.0m span with a depth of the girder1.0m are shown in figure 2. Determine the magnitude and direction of the reaction atsupport A if the vertical component of the force reaction at support B is one half that atA so that the system will remain in Equilibrium.8. In problem 7, determine the magnitude and direction of the vertical component of theforce reaction at support B.9. In problem 7, determine the magnitude and direction of the horizontal component of theforce reaction at support B.10. In problem 7, draw the FBD of the whole figure and determine the distance x such thatthe system will remain in equilibrium. Figure 2:20KN70°A0010 KN3M10.0 MIS KNXB1.0M

Answered: Image /qna-images/answer/57bc57b3-9577-47d7-ab5f-a3369934a9e6.jpg

Answered: Figure 2: 20KN 70° A 00 10 KN 3M 10.0 M…

Engineering

Civil Engineering

Figure 2: 20KN 70° A 00 10 KN 3M 10.0 M IS KN X B 1.0M

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: The beam is subjected to the internal moment of M = 2.6 kN?m Determine the maximum bending stress…

A: Given : M = 2.6 kN-m Determine the max. bending stress developed in the beam ?

Q: What steel area(s) must be provided? service live load = 37 kN/m calculated dead load = 16 kN/m…

A: Given,service live load= 37 kN/m calculated dead load = 16 kN/m simple span length = 5.4 m b= 250…

Q: Problem 7.1 - Determine the force in each member of the truss by t method of joints and state…

A: To find force in all members of the truss

Q: Problem No. 1 A flexible pavement for an urban interstate highway is to be designed using the AASHTO…

A: AASHTO Method: The design of flexible pavement is carried out using the AASHTO method in which…

Q: Determine the value of bending moments at the support using method distribution method W₁ 2.5m M₁…

A: Given: A continuous beam Required: Bending moment at support using moment distribution method

Q: Which of the following nearly gives the frictional force at the 550lb block? a. 200 lb b. 420 lb…

A: Answer let us draw the free body diagram of forces acting on the given arrangement We know that…

Q: Given truss - compute the reactions Ay, Gy :) force :) clet the at bars вс, BD, СЕ. $100kn

A: To find support reaction and force in member BC,BD,CE

Q: 1 Find the forces in members BC and EC. F lalu 4 P = 3 KN m E Lim أحد B 키 Q = 5 KN 1.5m P 0= 40⁰°

A: Given data in question Load 3 and 5 kN Angle 40° Span lengths To find out Member forces in BC…

Q: Q1: A steel LPG tank is shown in the figure. The wall thickness of the tank is 15 mm and has a yield…

A: Answer We are given t = 15 mm fy = 340 Mpa Internal pressure p = 3 Mpa diameter of tank = 1.5 m…

Q: h = 100 a.) Construct stress blocks which show the stresses acting on the cross-section at A and B…

Q: Consider the beam shown in (Figure 1). Suppose that w1 = 800 N/m and w2 = 500 N/m.

A: Given : w1 = 800 N/m and W2 = 500 N/m To Find :

Q: 25. A W14×257 A992 column in a building has effective lengths of 16 ft for both axes. Determine…

A: Reference : Structural Analysis, Steel Column. Given : Dead load and Live load. To determine :…

Q: 9.2 Indicate what footing type is appropriate for the following building conditions: a) High-rise…

Q: 1- What force is required to punch a 20-mm-diameter hole in a plate that is 25 mm thick? The shear…

A: “Since you have asked multiple questions, we will solve the first question for you. If you want any…

Q: Select the lighte the compression chord of a truss to carry 40 ki dead load and 45 kips live load.…

A: Given:-dead load=40 kips live load=45 kips 5 ft intervalschord braced=10 ftA992 and A572 Grade…

Q: Q5. Determine the volumetric flow and the pressure in the pipe at A if the height of the water…

A: Volumetric flow Pressure in the pipe at A

Q: 9. The following are the details for the backfill material in a vibroflotation project. D10=0.36 mm…

Q: etermine the forces in members BE and CE of the loaded uss. 3m 45° 5 kN 3m B E BC = CD 3 kN 3m

Q: 1. What is surveying? State its objects and uses 2. Distinguish between Geodetic and plain surveying

A: Surveying or land surveying is the method, calling, craftsmanship, and study of deciding the…

Q: A line was found to be 2,395.25 m long when measured with a 30 m tape under a steady pull of 3 kg.…

A: Given data: Measured length (ML) = 2395.25 m Tape length (L) = 30 m Applied pull (P) = 3 kg Mean…

Q: Q6 Draw the influence line for the force in (a) member JI, (b) member IE, and (c) member EF. L K J I…

A: Given Data: Total span=36 ftH=8 ftPannel span =6 ft eachTo determine Influence Line for Member JI,…

Q: A trailer weighing 2600 lb is attached to a 3100-lb pickup truck by a ball-and-socket truck hitch at…

A: Given data:- The given trail weighing,P=2600 lb Attached a, Q=3100 lb

Q: A L1 B P1 L1 The steel beam ABC has a central point load P1 = 40 kN acting at a distance L1 = 2.8…

A: Given S355 Grade Universal beam is used.

Q: Draw the shear and moment diagram for the overhang beam A -3m- B-- 4 kN/m -3m-

A: Given data:-

Q: 4.38 Two liquids with different densities and viscosities fill the gap between parallel plates as…

Q: A floor system consists of a 80mm concrete slab supported by continuous T beams with a span 7.3 m…

A: Given concrete slab thickness=80mmspan=7.3mmcenters=1.2mbw=280mmd=500mmfactored…

Q: B 16-28. The gear A on the drive shaft of the outboard motor has a radius A = 0.7 in. and the meshed…

Q: Column Load at Grid A1 L1 L2 + L1 + L1 The floor construction in this structure comprises two way…

Q: Calculate the Minimum X distance on the drawing below: 1.000 O 1.966 O 2.000 .460 C O 2.009 2.000…

Q: Which of the following gives the force applied, P? a. 420 lb b. 140 lb c. 320 lb

Q: aw the Axial Force Diagram (NFD), Shear Force Diagram (SFD) and MD) for the beams shown.

Q: The figure below shows a new cast-iron pipeline that connects two reservoirs. The upstream reservoir…

A: Given, Z1 = 1000 ft Q = 5 cfs L1 = 300 ft L2 = 700 ft

Q: 4. What are the fundamental principles of surveying? Explain briefly

A: Answer Fundamental Principles of Surveying are as follows 1) Work from hole to the part 2)…

Q: A C8 x 11.5 is connected to a gusset plate with 7/8-inch-diameter bolts as shown in Figure P3.2-3.…

A: Given Data: For grade 50 A572 Fy=50 ksi Fu=60 ksi t=0.75 m For the given channel section from manual…

Q: A two-phase signalized intersection is designed with a cycle time of 100 s. The amber and red times…

A: Given- 2-phase signalized intersection- Cycle time=100 s, Amber time=4s, Red time=50s, Total lost…

Q: Determine variables requested below for a horizontal curve with the following characteristics.…

A: Given Data: The data for the horizontal curve is given as: lane width=14ftnormal…

Q: The answers to the head loss and Ry are correct but Rx is wrong. Rx should be 170 N, could you try…

A: Given a 45 degree bend with one end open to atmosphere so Guage pressure at exit will be zero. Draw…

Q: INSTRUCTIONS: (USE METHOD OF SECTION) A. Determine the forces in all members with (•) marks of the…

A: Figure is as shown

Q: H.W.) A 10 g of steam initially at 120 °C is mixed with 50 g of ice at -10 °C. What will be the…

Q: Use method of sections to determine the forces in members BC and CF of the truss (You must use only…

Q: A 30 in. tubular shaft is in torsion under torque 33 lb-in.. Its cross section shown below with…

A: Given: Torque= 33 lb-inch Outer diameter= 3.2 inch Inner diameter= 1.0 inch Required: Shear…

Q: Why crack develop in slab

Q: Chapter 7: Use the method of sections to determine shear and moment in the middle of segment BC for…

A: To find shear and moment at mid of section of BC

Q: Calculate the diameter of the sewer pipe to be laid in mm (rounded to the nearest 50 mm) in order to…

Q: Given the soil profile below, determine the Total Stress, Neutral Stress and Effective Stress at…

A: Answer We are given Dry sand height H1 = 1.9 m Capillary or saturated sand H2 = 0.95 m saturated…

Q: structural beam and Figure 2 the cross section the beam. Additional to all the loadings shown beam…

A: Given:-OD=120mmt=7mmE=200GPaG=70GPaTo find:-principle and in plane maximum shear strains

Q: defined by the equation y=0.08.x². At the instant x - 10 m, the toboggan's speed is 5 m/s. At this…

Q: 7. The results of field unit weight determination of a soil sample using the sand cone method is as…

Q: One shaft is in torsion as shown below. If the magnitude of shear stress at point A is 245.3 MPa,…

A: Given: Magnitude of shear stress at point AζA=245.3 MPa. From the figure, Distance of point A from…

Q: Q3) Several forces are applied to the steel pipe assembly shown below. The pipe has inner and outer…

A: A pipe section is given below. To this load are applied as mentioned. The pipe is fixed at its base…

Concept explainers

Traverse Survey

Traverse surveying is a popular method of surveying. Traversing is that type of survey where several connected survey lines form a framework and the directions and lengths of the survey lines are measured with the help of a tool to measure angles and tape or chain respectively. Traverse networks involve placing survey stations in a queue or trail and using pre-tested points as a basis for looking at the next point. This type of surveying is different from Tacheometric surveying, where only angles are measured and the process of chaining is reduced.

Question

7. The wheel loads on a small tractor crossing a 10.0m span with a depth of the girder
1.0m are shown in figure 2. Determine the magnitude and direction of the reaction at
support A if the vertical component of the force reaction at support B is one half that at
A so that the system will remain in Equilibrium.
8. In problem 7, determine the magnitude and direction of the vertical component of the
force reaction at support B.
9. In problem 7, determine the magnitude and direction of the horizontal component of the
force reaction at support B.
10. In problem 7, draw the FBD of the whole figure and determine the distance x such that
the system will remain in equilibrium.

Figure 2:
20KN
70°
A
00
10 KN
3M
10.0 M
IS KN
X
B
1.0M

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step 3

VIEW

Step by step

Solved in 3 steps with 3 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

A uniform bar AB is resting in a horizontal position on smooth inclines as shown below. Determine the load P that will hold the bar in equilibrium. Also, determine the reactions at A and B. Wherein: Q=2 T=6 Example: 2QT kN = 226 kN T.Q5 m = 4.25 m
The bar system given in the figure above, (between AB: 1m / BC between: 3m / CD: 2m) a) Show the support reactions and load occurring on the rod. b) Do you calculate support reactions? c) Calculate the Normal Force, Shear Force and Moment values by cutting from the points you have determined. d) Draw cross-section impact diagrams? Do you specify the maximum positive and negative moment values? e) Check the cross-sectional influence diagrams with a simple method, briefly explain the control steps.
A beam is loaded as shown in the given figure. 1. Which of the following gives the max. shear? a. 15 kN b. 13 kN c. 14 kN d. 12 kN 2. Which of the following gives the max. positive moment? a. 13.8 kN·m b. 13.5 kN·m c. 14.0 kN·m d. 12.8 kN·m 3. Which of the following gives the location of max. pos. moment from point B? a. 2.0 m b. 3.4 m c. 3.0 m d. 2.4 m
A very important load on a structure is the pressure load. This loading is simplified for mathematical calculations such as a right triangle. In this case, a vertical (wooden) solid, where the force of the water pressure will be horizontal and is linearly distributed in a triangular shape and the greatest force due to the water pressure at point B is Y kN. Below this structure, calculate the support reactions acting at points A and B. (Disregard the proper weight of the wooden board) X=9 Y=60
An equivalent force-couple system: Three forces F1 = 100 N, F2 = 50 N, and F3 = 30 N act on a structure as shown in the figure where α = 30o, θ = 60o, L = 1 m and h = 0.5 m. Find the equivalent force-couple system about point D.
In the beam loaded as shown in the figure, 4. Find the reaction at the left support. a. 36 kN b. 25 kN c. 15 kN d. 35 kN 5. Find the absolute max shear a. 41 kN b. 71 kN c. 90 kN d. 105 kN 3. Find the location of maximum positive beam moment measured from point a. a. 4.437 m b. 5.437 m c. 1.732 m d. 2.273 m
A 50 kg fisherman sits at the center of the boat rented in a private resort, which has a uniform width and a weight per linear foot of32 lb/ft, that will be used for island hoping in the area. The boat is 3 m long. Assume that the water exerts a uniform distributed load upward on the bottom of the boat. c) What is the maximum bending moment (lb-ft) exerted on the boat? d) At what distance from the left side of the boat the maximum bending moment occurs?
In the figure provided below: determine the vertical reaction at Point B and E.
Consider the overhang beam shown in (Figure 1). Suppose that P = 6 kN, M= 6 kN⋅m, w= 4 kN/m. Point D is located just to the left of the roller support at BB, where the couple moment acts. Follow the sign convention. Part A Determine the internal normal force at point D. Express your answer to three significant figures and include the appropriate units. Part B Determine the internal shear force at point D. Express your answer to three significant figures and include the appropriate units. Part C Determine the internal moment at point D. Express your answer to three significant figures and include the appropriate units. Part D Determine the internal normal force at point E. Express your answer to three significant figures and include the appropriate units. Part E Determine the internal shear force at point E. Express your answer to three significant figures and include the appropriate units. Part F Determine the internal moment at point…
Consider the simply supported beam shown in (Figure 1). Suppose that P = 18 kN , w = 7 kN/m . Point D is located just to the left of the 18-kN concentrated load. Follow the sign convention. Part A Part complete Determine the internal normal force at point C. Express your answer to three significant figures and include the appropriate units Part B Determine the internal shear force at point C. Express your answer to three significant figures and include the appropriate units. Part C Determine the internal moment at point C. Express your answer to three significant figures and include the appropriate units. Part D Part complete Determine the internal normal force at point D. Express your answer to three significant figures and include the appropriate units. Part E Determine the internal shear force at point D. Express your answer to three significant figures and include the appropriate units. Part F Determine the internal moment at…
The 10 m ladder weighing 35 kg is resting on a horizontal floor at A and on the wall at B making an angle of 60° from the horizontal. The coefficient of friction between the ladder and the floor and between the ladder and the wall is 0.25. 1. Determine the distance "x" to which the 72 kg man can climb on the ladder without causing the ladder to slip at its lower end A. 2. Determine the reaction at the wall B. 3. Determine the reaction at the horizontal floor at A.
The bar system given in the figure above, (between AB: 1m / BC between: 3m / CD: 2m)a) Show the support reactions and load resultant on the rod?b) find the support reactions?c) find the Normal Force, Shear Force and Moment values by cutting from the points you have determined?d) Draw the cross section effect diagrams? Indicate the maximum positive and negative moment values?e) Check the cross-section influence diagrams with a simple method, explain the control steps briefly?