7. Three rods of different materials are connected as shown in the figure. (a) Determine the maximum safe load P in kN if the total deformation is limited to 5 mm. Using the value of P from the previous item, (b) determine the normal stress developed in the bronze rod, steel rod, and aluminum rod. Express your answers in MPa. Use Est = 200 GPa, Eal = 83 GPa, and Ebr = 70 GPa. Steel Bronze Aluminum A = 500 mm? A = 600 mm? A = 300 mm? P 4P 5P 2P 1.0 m 2.0 m 1.5 m

7. Three rods of different materials are connected as shown in the figure. (a) Determine the maximum safe load P in kN if the total deformation is limited to 5 mm. Using the value of P from the previous item, (b) determine the normal stress developed in the bronze rod, steel rod, and aluminum rod. Express your answers in MPa. Use Est = 200 GPa, Eal = 83 GPa, and Ebr = 70 GPa. Steel Bronze Aluminum A = 500 mm? A = 600 mm? A = 300 mm? P 4P 5P 2P 1.0 m 2.0 m 1.5 m

Steel Design (Activate Learning with these NEW titles from Engineering!)

6th Edition

ISBN:9781337094740

Author:Segui, William T.

Publisher:Segui, William T.

Chapter1: Introduction

Section: Chapter Questions

Problem 1.5.6P: The data in Table 1.5.3 were obtained from a tensile test of a metal specimen with a rectangular...

See similar textbooks

Similar questions

The results of a tensile test are shown in Table 1.5.2. The test was performed on a metal specimen with a circular cross section. The diameter was 3 8 inch and the gage length (The length over which the elongation is measured) was 2 inches. a. Use the data in Table 1.5.2 to produce a table of stress and strain values. b. Plot the stress-strain data and draw a best-fit curve. c. Compute the, modulus of elasticity from the initial slope of the curve. d. Estimate the yield stress.
Compare the engineering and true secant elastic moduli for the natural rubber in Example Problem 6.2 at an engineering strain of 6.0. Assume that the deformation is all elastic.
The cross section of the AB part of the welded pipe part given in the figure is a hollow pipe and the cross section of the BC part is a circle with a solid body. The inner diameter of the pipe section is 20mm and the outer diameter is 28mm, while the diameter of the full body part is 12mm. Determine the average normal stress at the D and E points accordingly.
Determine the a.Stress at 167 kN loadin MPa b.Strain at 167 kN loadin mm/mm(expressed in scientific notation) c.Modulus of elasticityMPa d.Modulus of resiliencein N-mm/mm3 e.Modulus of toughnessin N-mm/mm3
Bars (1) are made of a polyimide plastic that has an elastic modulus of 3.8 GPa. Bar (2) is a nylon material that has an elastic modulus of 0.9 GPa. Each bar has a cross-sectional area of 1050 mm2. Using L = 395 mm and Δ = 7.3 mm, what magnitude of load P will cause the normal stress in each bar to be the same value? [Answer: P = 67.0 kN]
Determine the average normal stress in each rod if T2=400∘F Calculate the new length of the aluminum segment.
A cylindrical rod AB has a length ? = 80 cm and a diameterof ? = 2 cm. The modulus of elasticity is ? = 200 GPa andyield strength is ?? = 300 MPa. The stress-strain diagram ofthe rod is shown in the left figure. A force ? = 100 kN isapplied to the bar and then fully removed (right figure).Determine the permanent set in the rod.
Bars (1) are made of a polyimide plastic that has an elastic modulus of 3.8 GPa. Bar (2) is a nylon material that has an elastic modulus of 1.9 GPa. Each bar has a cross-sectional area of 900 mm2. Using L = 395 mm and Δ = 4.6 mm, what magnitude of load P will cause the normal stress in each bar to be the same value?
For the beam shown, determine the support reactions and draw the stress diagrams. shear and bending moment. EI is constant. The rigth answer is: VA = 1.3 kN (↑); HA = 0 kN; MA = 4.40 kN.m (clockwise); VB = 51.20 kN (↑). I don't know how to get these results, please show how, step by step.
The structure shown below consists of a brass core inserted into a steel tube of cross sectionsquare. If a moment of 8 kN × m is applied at its end, determine the maximum bending stress in thebar. E (brass) = 100 GPa, E (steel) = 200 GPa.
When an axial load is applied to the ends of the two-segment rod shown in Figure P2.1, the total elongation between joints A and C is 7.5 mm. The segment lengths are a = 1.2 m and b = 2.8 m. In segment (2), the normal strain is measured as 2,075 um/m. Determine:(a) the elongation of segment (2).(b) the normal strain in segment (1) of the rod. (Ans. to check: Normal strain (1) = 825uE
Please answer this question, An aluminum rod is rigidly attached between a steel rod and a bronze rod as shown in the figure. Axial loads are applied at the positions indicated. Find the stress of each rod in MPa