(8) A 600 ohm strain gage is connected into a bridge circuit with the other three resistors R1 = R2 = R3 = 600 ohms. The bridge is powered by a 10 volt DC power supply. The strain gage has a gage factor k = 2.0. The bridge is balanced (Vout= 0 volts) when the strain :, = 0. What is the strain when Vout= +500 microvolts? R3 R1₁ Yout Rs STRAIN R2

(8) A 600 ohm strain gage is connected into a bridge circuit with the other three resistors R1 = R2 = R3 = 600 ohms. The bridge is powered by a 10 volt DC power supply. The strain gage has a gage factor k = 2.0. The bridge is balanced (Vout= 0 volts) when the strain :, = 0. What is the strain when Vout= +500 microvolts? R3 R1₁ Yout Rs STRAIN R2

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter6: Power Flows

Section: Chapter Questions

Problem 6.61P

See similar textbooks

Similar questions

The impedances of the bridge are as follows, Z1: A resistor R1 in parallel with C1. Both R1 and C1 are known Z2: R2 , an adjustable resistor of known value Z3 : An adjustable resistor R3 in parallel with an adjustable C3 where values of R3 and C3 are known. Z4: A capacitor C4 of known value in series with R4 an unknown resistor Determine the real and imaginary parts expressions for the balance condition
Suppose that the resistive components in the DC bridge shown in Figure 7.2 have thefollowing nominal values: Ru = 330 ohms ; R1 = 470 ohms ; R2 = 560 kohm; R3 = 270 kohm. Theactual value of each resistance is related to the nominal value according to:Ractual = Rnominal + þ vR where vR has the following values: vRu = 5 ohm ; vR1 = þ4 ohm;vR2 ¼ þ6 U; vR3 ¼ 9 U. Calculate the open circuit bridge output voltage if thebridge supply voltage Vi is 12 V.
•What is the total impedance of the circuit? • Is the circuit inductive, capacitive, or neither (resistive)? •What is the total power (apparent) delivered by the voltage source? •Draw the phasor diagram of the voltage and current at the source. •What is the current passing through the R2 and L. branch? •Draw the phasor diagram of the voltage and current at the R2 and L branch.
Identify the equation that proves Kirchhoff's Voltage Law for the circuit below given the following:ES1 = 8 V, ES2 = 14 V, R1 = 12 Ω, R2= 10 Ω, R3 = 22 Ω, and IT = 0.5 A
1) Use the superposition principle to determine the current in the load resistance RL, in the dc circuit of Figure QA1(a) 2) The current through a pure capacitor is given byi = 28.28cos(314t).Derive an expression for the voltage across the capacitor in the form v = Vm cos(wt) and comment on your answer. 3)Estimate the value of the current I and the voltage V in each of the circuits shown in Figure QA1(c) and justify your method of estimation.
4.Two storage batteries are connected in parallel to supply a load having a resistance of 0.20ohm. The emf of the firstbattery is 12.1-V and that of the other is 11.8-V. The internal resistances are 0.20ohms and 0.23ohms, respectively. Determine the terminal voltage. Use Kirchhoff’s Circuit Analysis Method.
Differential equation is given as- Vo(t) = Vdd(1- (R/(R+Ron))*e^(-t/RC)) a) Assume Ron=280 ohm. When the load capacitor is C = 0.5nF, the output must reach 90% of its final value by t = 25uS. Find a value of R that will satisfy this requirement while at the same time keeping the static power below 1 mW. For your chosen resistance, calculate how long it will take to reach the 90% level.
1) A Wheatstone bridge has a strain gage in the lower right leg with a 100 ohm nominal resistance. It is mounted on steel with a Modulus of Elasticity (E) equal to 30x106 lb/in2. The other resistors are equal to 100 ohms. The bridge voltage is 5 V. a) What is the bridge output in V per 1250 lb/in2 of stress? Assume the Gage Factor = 2.0. b) What is the loading error produced by measuring the output with a voltmeter having an input impedance of 70 KΩ. c) If the bridge and the strain gage is used to measure the strain on a steel structure with a strain of 700 microstrain (u strain), what will be the bridge output in Volts?
For the circuit of Figure 4.8, determine the source current and the current through each of the three components. Also, draw a phasor diagram of E, vL and vR. Source voltage is 7 volts RMS NOTE: All measurements are in standard units (volts, ohms, farads) unless otherwise stated.
Construct the series-parallel circuit in below. Use R1 = 330Ω, R2 = R3 = 1kΩ using Proteus Simulation Software. Then, connect a dc voltage supply with Vs = 10V across points A and B. Measure the voltage across each resistor using a dc voltmeter. Does your observation agree with the Kirchhoff Voltage Law
Answer the following questions related to a series/parallel combinational circuit configured as follows: R1 is in series with the source and also in series with the parallel combination of R2 and R3. The circuit’s voltage is +24VDC, R1= 4.5kΩ, R2=30kΩ, and R3=10kΩ. What is the Thevenin’s resistance (RTH) for the circuit described above if a load resistance of 20kΩ is placed in parallel with R2 and R3?
The AC Bridge shown below is used to measure an unknown inductance, Lx and its internal resistance, Rx. The Bridge parameters are R1 = 20,000 ohms, R2 = 50,000 ohms, C2 = 0.003 μf, ω= 105 radians per sec. C1 is adjustable from 10 pf to 150 pf, and R3 is adjustable from 0 to 10,000 ohms. At Balance,I. Derive expressions for Rx and Lx in terms of ω, R1, R2, R3, C1, and C2.II. Determine the largest values of Rx and Lx that are measurable with the given parameters.