I need the answer as soon as possible 8Consider the bridge shown next, with C, = 0.1 nF,R, = 20k Ohms, R2 = 10k Ohms, R3 = 1 k, andw = 3k rad/sec. It is concluded thatRIR2CiGRswwwwR3LsThe bridge is not suitable since Q > 10The bridge is not suitable since Q < 10The bridge is suitable since Q <10The bridge is suitable since Q >10None of the choices

In the circuit, Choose the correct option. What is value of quality factor?

8 Consider the bridge shown next, with C, = 0.1 nF, R, = 20k Ohms, R2 = 10k Ohms, R3 = 1 k, and w = 3k rad/sec. It is concluded that RI R2 Ci G Rs R3 Ls The bridge is not suitable since Q > 10 The bridge is not suitable since Q < 10 The bridge is suitable since Q <10 The bridge is suitable since Q >10 None of the choices

8 Consider the bridge shown next, with C, = 0.1 nF, R, = 20k Ohms, R2 = 10k Ohms, R3 = 1 k, and w = 3k rad/sec. It is concluded that RI R2 Ci G Rs R3 Ls The bridge is not suitable since Q > 10 The bridge is not suitable since Q < 10 The bridge is suitable since Q <10 The bridge is suitable since Q >10 None of the choices

Delmar's Standard Textbook Of Electricity

7th Edition

ISBN:9781337900348

Author:Stephen L. Herman

Publisher:Stephen L. Herman

Chapter18: Resistive-inductive Parallel Circuits

Section: Chapter Questions

Problem 11PP: In an R-L parallel circuit, ET=208 volts, R=2.4k, and XL=1.8k. Find IT.

See similar textbooks

Similar questions

Circuits Find voltage vab using superposition theorem? VAB? VAB’?vab “?
Norton's Theorem. VT=14V,R1=6ohms,R2=8ohms,R3=10ohms. Nortonize this circuit for R3 as load resistance by finding IN & RN then find IL & VL. Check results by finding I3 & V3
Redraw the Norton Equivalent circuit for Thevenin Equivalent Circuit using a previous problem that was solved and calculate the load current (?? ) dropped across the load resistor (?? )? NOTE (backround information): for this example and the circuit you see below we were asked to perform Thevenins equivalent circuit. We were asked to find... Rth, Eth, and IL the anwers I got were Rth= 1 kΩ Eth= 3 V IL= 0.273 mA
1)draw the circuit in its simplest form? 2)Simplify the circuit using Boolon algebra?
a. Form the node voltage equation for the supernode defined by the controlled voltage source.b. Form the node voltage equation for the node whose voltage is ? . 2c. Form the equation that specifies the constraint imposed by the controlled voltage source on the nodes it is connected to.Note: All equations should be in terms of the node voltages ?_1, ?_2, and ?_3 only and should have no other unknowns. They should also be written in the simplest form.
Perform the following steps for the given circuit in below.RD = RS = 1kΩ, R1 = 300kΩ, R2 = 100kΩ, VDD = +12V, IDSS = 12mA, VP = -4Va) Calculate the ID current, VDS and VGS voltage and determine the region of operationfor the JFET. (Hint: Use Thevenin’s Theorem)
1. What are the Advantages and Dis-advantages of using Mesh Analysis for solving Circuit Problems? Please make an example? 2. What are the Advantages and Dis-advantages of using Nodal Analysis for solving Circuit Problems? Please make an example?
For R1=6000, R2=6000, R3=6000, R4=1000, I1=0.008, V1=12, in the circuit shown below,then what is the value of :?a and ib and Vc and id
. Compare and Contrast them when are they most effective and not, their pros and cons. Give you detailed observation on the similarities and differences of the network laws and theorem KCL and KVL Maxwell's Mesh AnalysisNodal AnalysisBe specific and detailed.
Mesh and ring topologies are typical network configurations. Please be as specific as you can.
Consider the network in the figure Q1.3. Shown below. Use nodal analysis to determine the voltage V_1 at node 1 and V_2 and node 2
circuit analysis Please ignore Turkish translations. For the circuit in the figure, answer by considering the values of Vs= 69 V, Is=3.3A R1=1Ω, R2=2Ω, R3=3Ω, R4=4Ω, R5=1.5Ω and using the node voltages method. v1=? v2=? voltage of the circuit v=? power of current source Pıs=? power of voltage source Pvs=?