8 kN, 2) Find the torque created by the 2 forces about the origin. 4 kN Ignore the 15 kNm load. (It is called a couple moment, and would normally just be added to the total moment, 15 kN-m [0.5 m independent of where it was applied) -1.5 m 1.5 m-1.5 m- 1.5 m-

8 kN, 2) Find the torque created by the 2 forces about the origin. 4 kN Ignore the 15 kNm load. (It is called a couple moment, and would normally just be added to the total moment, 15 kN-m [0.5 m independent of where it was applied) -1.5 m 1.5 m-1.5 m- 1.5 m-

Name: Please help me 8 kN,2) Find the torque created by the2 forces about th
Uploaded: 2024-03-20T06:56:55.000Z
Channel: Bartleby
Description: Please help me 8 kN,2) Find the torque created by the2 forces about the origin.Ignore the 15 kNm load. (It iscalled a couple moment, andwould normally just be addedto the total moment,y5/44 kN3[0.5 m15 KN•Mindependent of where it wasapplied)-1.5 m 1.

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter6: Beams And Cables

Section: Chapter Questions

Problem 6.6P: Find the internal force systems acting on sections 1 and 2.

See similar textbooks

Similar questions

Which of the following gives the moment MD about point D of the tensile force TBA exerted by the wire at point B? Note that rB/D = (4i - 6k) m and TBA = (-8i + 6j + 4k) kN and that MD = rB/D x TBA. a. (36.0i + 32.0j + 24.0k) kN-mb. (48.0i + 24.0j + 16.0k) kN-mc. (-36.0i - 32.0j - 24.0k) kN-md. (16.0i - 12.0j -8.0k) kN-m
An engineer is using the pliers shown below to twist a pin at P. Based on the parameters given, find the moment about P due to Force 2.
Find the moment caused by the force F = 898 about point C if a = 27 , b = 40 , m =17, and n = 4. Round off only on the final answer expressed in whole number.
The light boom AB is attached to a vertical wall by a ball and socket joint at A and supported by two cables at B. A force P is applied at B where P = 16i - 13j kN.Note that the reaction force at A acts along the boom because it is a two-force member. Calculate the magnitude of the reaction force at A in kN. Determine the magnitude of the moment of P about the y-axis in Nm. Determine the magnitude of the moment of P about the z-axis in Nm. Determine the magnitude of the moment of P about the origin (point O) in Nm.
In the figure below, set up an equation related to the moment (M) about the paired force (F).
A motor attached to the shaft at O causes the arm to rotate over the range 0≤θ≤180∘. The unstretched length of the spring is 0.65 m, and it can support both tension and compression. If the net moment about O must be zero, determine and plot the required motor torque M as a function of θ. Draw the plot and then answer the questions.Assume k = 780 N/m, r = 0.47 m, a = 0.32 m.
A beam which is pinned at point A is subjected to three external forces. Determine the net moment of the force system about point A. 175 N-m CCW A picture is provided below showing the details of this problem.
The figure shows a control bar, subjected to a force of 90N. Since the length of the bar is 225 mm and the moment of the clockwise force on B is 13.5 N.m, determine the value of α. Solve the problem using scalar notation and explain your result.
Refer to the diagram and use g = 9.81 m/s2. Determine the moment about A due the weight of 60 kg mass, = ____ mN. Assume the pulley at D is frictionless and the tension in the cable is T. Determine the vertical component of the force applied at E, Ey = ____. Draw the free body diagram of the beam on paper, and write the equation of moment about A. determine the tensional force in the cable, T = ____ N. determine the vertical component of the force applied at E, Ey = ____ N. determine the horizontal component of the reaction force at A, Ax = ____ N. determine the vertical component of the reaction force at A, Ay = ____ N. determine the magnitude of the reaction force at A, = ____ N.
What is the couple moment about A? the coefficients for i, j and k
Solve for the resultant forces and moments at points A and B in diagram below
The magnitude of the moment of the force F=300i-200j+600k N about the y-axis is. Select one: a. 240 [N.m] b. 20 [N.m] c. -240 [N.m] d. -20 [N.m]