This is the question 8. The input to a 220 V d.c. shunt motor is 11 kW. Calculate (i) te torquedeveloped (ii) th eficicnc (i the spee this load. The partculars ofthe motor are:No-load current = 5A; No-load speed = 1150 r.p.m;Armature resistance= 0,5 0; shunt field resistance%=1100.

Shunt motors-Shunt motors have very good speed regulation, that is, they try to move at or close to…

Answered: 8. The input to a 220 V d.c. shunt…

8. The input to a 220 V d.c. shunt motor is 11 kW. Calculate (i) the torque developed (i) the efcic (i t sped t this load. The pariculars of the motor are:

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

A 110-V shunt generator has a full-load current of 100 A, shunt fieldresistance of 55 Ω and constant losses of 500 W. If F.L. efficiency is88%, find armature resistance. Assuming voltage to be constant at 110 V,calculate the efficiency at half F.L. And at 50% overload. Find the loadcurrent. Write the answer neatly.
A separately excited DC motor is rotated at 1000rpm, The variation of armature terminal voltage as a function of field current is measured under no-load conditions and tabulated below: IF 0.0 0.1 0.2 0.3 0.4 0.5 0.6 0.7 0.8 VT 0 30 60 85 102 115 124 130 134 The field winding supply VF=24V and the field resistance is adjustable. The armature winding resistance RA=0.2? and the armature terminal voltage VT=130V. a. Calculate the field current if the motor is operated with no-load at 1000 rpm b. The motor drives a load at 1200 rpm. Calculate the armature voltage at 1200 rpm if the field resistance RF=60? c. Calculate the torque for the above condition d. The motor supplies a mechanical load of 4000W at 1450rpm. The mechanical rotational losses are 160W, calculate the efficiency
A 110V shunt generator has a full load current of 100A, shunt field resistance of 55 ohms and constant losses of 500W. If full load efficiency is 88%, find the armature resistance. Assuming voltage to be constant at 110V, calculate the efficiency at half load. Find the load current.
A separately excited dc motor has the following parameters: 220 V, 10 A, 1,400 rpm, armature resistance = 2.3 Ω, field excited at rated current. When the armature is open-circuited and rotated at 1,500 rpm by a prime mover, the armature voltage was 250 V. If the motor is now supplied at rated voltage and if it carries 5.6 A armature current, what will be the approximate load torque on the shaft?
For a certain load and a constant terminal voltage VT of 230 V, DC shunt motor takes an armature current of 20 A. The armature resistance is 0.5 Ω. Rotation and ohmic losses can be neglected. Find the resistance required in series with armature to reduce the speed by 50% of the original motor speed if: a) The load torque TL is constant. b) The load torque is not constant but is proportional to square of the motor speed, i.e. TL = kT × ω2
Q/ A 250 V dc series motor having armature and field resistance 0.25 ohm and 0.15 ohm respectively runs, at 800 rpm, while taking 50 A from the supply. Assuming the magnetic circuit of the motor to be unsaturated, determine its speed, when a divertor of 0.3 ohm resistance is connected in parallel with the field winding of the motor, which is subjected to a load torque whose torque (a) remains constant regardless of speed, (b) varies in direct proportion to the speed, (c) varies as the square of the speed.
A 35.2 HP, 250 V, 100 A, 1200 RPM, series DC motor with no armature reaction is considered in this problem. This motor has a series-field winding of 5 turns per pole. Its armature resistance in RA =0.05 ohm, and its series field resistance is Rs =0.05 ohm. The magnetizationcurve at 1200 RPM is given by the following table:
The armature winding resistance of a long shunt connected DC generator is 0.4ohm, the resistances of the shunt and serial field windings are 125 ohms and 0.1 ohms, respectively. While the generator supplies 8KW of power to the load it feeds, which is the voltage it produces since the output voltage is 250V?
A 4 pole10V, DC shunt motor operates on a load current 10A, having wave connected armature with 200 conductors. The flux per Pole is 25 m Wb. Resistance of shunt field winding is 1 ohm and resistance of the armature is 0.15 ohm. a) based on the back emf voltage, is it possible to be achievable this value? Give reason.
A permanent-magnet dc motor hasRA = 7 Ω, VT = 200 V, and operatesunder no-load conditions at a speed of 1600rpm with IA = 0.5 A. A load is connectedand the speed drops to 1400 rpm. Determinethe efficiency of the motor under loadedconditions. Assume that the losses consistsolely of heating of RA and frictional losstorque that is independent of speed.
a shunt-wound motor runs at 600 r.p.m from a 230 V supply when taking a line current of 50 A. its armature and Field resistance are 0.4 ohms and 104.5 ohms respectively. Neglecting the effects of armature reaction and allowing 2 V brush drop, calculate (a) the no-load speed if the no-load line current is 5 A. (b) the resistance to be placed in armature circuit in order to reduce the speed to 500 r.p.m when motor is taking a line current of 50 A . (c) the percentage reduction in the flux per pole in order that the speed maybe 750 r.p.m when the armature is 30 A with no added resistance in the armature circuit.
Consider a shunt DC motor with an armature resistance RA =0.2N and terminal voltage VT = 160 V. The motor rated speed is 1800 RPM. The total field resistance 240 Q. Assume No armature reaction in this machine. The variation of the armature terminal voltage as a function of the field current is measured under no-load conditions and shown below: IF (A) EA (V) 1.0 141 0.0 0.6 125 These values were taken at speed n= 1800 RPM 0.1 0.2 0.3 0.4 0.5 0.7 0.8 0.9 30 60 85 102 115 132 137 140 If the motor is driving a load at an armature current IA=60 A, its rotational speed is 1517 RPM, with rotational losses of 848 Watt. What torque is induced by this motor? Select one: O a. Induced Torque = 62 N.m O b. Induced Torque = 56 N.m O c. None O d. Induced Torque = 51 N.m.