80 kN 2 m 50 kN -1 m––1 m-|1 m--1 m-|

Q: Determine the average normal stress on each bar if subjected to the load shown. Three hanger bars…

A:

Q: A 40-lb weight is dropped from a height of h = 2 ft onto the center of the cantilevered A992 steel…

A: The properties of W10×15 are given as, The static deflection at mid-point is written as,

Q: Two A992 steel pipes, each having a cross-sectional area of 0.32 in2, are screwed together using a…

A: The modulus of elasticity of A992 steel is given by table, It is assumed that P force is acting in…

Q: The 30-mm-diameter A992 steel rod is subjected to the loading shown. Determine the displacement of…

A: The free-body diagram of the beam is given as, On using force equilibrium in the horizontal…

Q: The column is constructed from high-strength concrete and eight A992 steel reinforcing rods. If the…

A: Write the given data:

Q: Determine the vertical displacement of point C of the A992 steel beam. I = 80(106) mm4.

A: Given data: *The moment of inertia of the steel beam is I=80×10^4 mm4. *The young’s modulus of the…

Q: If the beam is made of material having an allowable tensile and compressive stress of (sallow)t =…

A: Given data as per the question  Allowable tensile stress =125 MPa   Allowable compressive stress…

Q: The fence board weaves between the three smooth fixed posts. If the posts remain along the same…

A: Given:- Question with solution To find:- To write the given solution in handwritten form

Q: The rigid beam is supported by a pin at C and an A992 steel guy wire AB of length 6 ft. If the wire…

A: Given data as per question Length of AB =6ft Diameter of wire = 0.2 in W = 200lb/ft

Q: The beam is shown in Fig. a has a cross-sectional area in the shape of a channel, Fig. b. Determine…

A: Given data  To determine the maximum bending stress that occurs in the beam at section a–a.

Q: The column is constructed from high-strength concrete and eight A992 steel reinforcing rods. If the…

A:

Q: P a

A: GIVEN DATA- 23.5-mm-diameter pin at A P = 28.36 kN, a = 2.25 m, and b = 6.56 m.

Q: The member consists of two plastic channel strips 0.5 in. thick, glued together at A and B. If the…

A: Draw the free body diagram.

Q: 9-55. The three suspender bars are made of A992 steel and have equal cross-sectional areas of 450…

A:

Q: The W24 * 104 A-36 steel beam is used to support the uniform distributed load and a concentrated…

A: Write the geometric properties of structural properties of the shape W24X104. Write the properties…

Q: The member consists of two plastic channel strips 0.5 in. thick, glued together at A and B. If the…

A: Given data: The intensity of the load, w0 = 3 kip/ft. Draw the free body diagram.

Q: Determine the torsional strain energy in the A992 steel shaft. The shaft has a radius of 40 mm.

A: Draw the side view of the shaft. Let AB be the segment 1, BC be the segment 2, and CD be the…

Q: *12-36. The beam is constructed from four boards which are nailed together. If the nails are on both…

A: Draw the free-body diagram of the beam.

Q: Beam AB has a square cross section of 100 mm by 100 mm. Bar CD has a diameter of 10 mm. If both…

A: Given Applied load = 10 kN Beam AB cross-section 100mm X100mm Bar CD diameter 10 mm Material type =…

Q: A 40-lb weight is dropped from a height of h = 2 ft. A 40-lb weight is dropped from a height of h =…

A: Here firstly we convert this problem into a static problem and then calculate the impact  bending…

Q: The simply supported beam is built up from three boards by nailing them together as shown. If P = 12…

A: Given data Point load applied at the center of the beam, P = 12 kN. Shear force resisted by each…

Q: 600 N/m The shaft is supported by a smooth thrust bearing at A and a smooth journal bearing at B.…

A:

Q: Q3) Determine the absolute maximum shear stress developed in the beam. 40 kN.m 20 kN.m B CCO 25 mm +…

A: Given data Width of the beam b = 125mm To determine the absolute maximum shear stress in the…

Q: The lever is attached to the shaft A using a key that has a width d and length of 25 mm. If the…

A: Given data:  Vertical force                          (Fy) = 200 N (downwards) (perpendicular to the…

Q: The post is constructed from concrete and six A-36 steel reinforcing rods. If it is subjected to an…

A:

Q: Determine the shear stress at point B on the web of the cantilevered strut at section a–a.

A: Given Applied loads 2 kN and 4 kN To find Shear stress at point B

Q: The strut is glued to the horizontal member at surface AB. If the strut has thickness of 25mm and…

A:

Q: Determine the vertical displacement of end B of the frame. Consider only bending strain energy. The…

A: The free body diagram of the horizontal beam is as follows: Calculate the moment at the y-y…

Q: ) The post is constructed from concrete and six A-36 steel reinforcing rods. If it is subjected to…

A:

Q: Q1/ In each case, draw the estimated elastic curve: 8 kN-m 8 kN

A: Given: That we have to find out the elastic curve of the second beam which is simply supported and a…

Q: Determine the total axial and bending strain energy in the A992 steel beam. A = 2850 mm2, I =…

A: Calculate the total vertical load due to the applied uniformly variable load i.e. the UVL. V=12wmaxL…

Q: The timber beam is to be loaded as shown. If the ends support only vertical forces, determine the…

A:

Q: Problem #3: The three suspender bars are made of A992 steel and have equal cross sectional areas of…

A:

Q: R12-7. The beam supports a vertical shear of V = 35KN. Determine the resultant force this develops…

A: V = 35 kN Moment of inertia about a centroidal axis, from tables I = 5.9584 x 10-5 m4 t = 12 mm Area…

Q: The column is constructed from high-strength concrete and eight A992 steel reinforcing rods. If the…

A: Given data: The axial force acting on the column, P = 200 kip. Length of column, L = 3 ft. The…

Q: Determine the maximum bending stress in the handle of the cable cutter at section a–a. A force of 45…

A: To find out the Moment about a-a axis ∑.M=0M-45(5+4cos25°)=0M=394.14 lb-in

Q: The beam is constructed from three plastic strips.  If the glue can support a shear stress of tallow…

A: Draw shear force and section diagram for the beam Maximum shear force in beam is 2P

Q: Determine the bending strain energy in the A992 steel beam. I = 156 in4.

A: The value of modulus of elasticity of the material is U=29×103 ksi. The moment of inertia of the…

Q: The A992 steel bars are pin connected at C and D. If they each have the same rectangular…

A: Structure is in equilibrium so  we can apply equilibrium condition. ∑nFY=0 ; RA+RE-500=0 ;RA+RE=500…

Q: The weight of 175 lb is dropped from a height of 4 ft from the top of the A992 steel beam. Determine…

A: Write the properties of the given beam. Write the expression for the stiffness of the beam and…

Q: The shaft is supported by a smooth thrust bearing at A and a smooth journal bearing at B. Determine…

A: Let us draw the all the reactions forces

Q: 12-15. Determine the shear stress at points C and D located on the web af the beam. so kNim -L8 m-…

A: Given: A simple supported beam I cross section To find the shear stress at point C and D

Q: Q1/ In each case, draw the estimated elastic curve: -4 m- 8 kN.m 2 kN/m 8 kN 4 kN

A:

Q: F12-7. Two identical 20-mm-thick plates are bolted to the top and bottom flange to form the built-up…

A: Understand that the cross section is symmetric about both and x and y axes the neutral axis of the…

Q: Determine the equation of the elastic curve. EI is constant.

A: A  uniform distributed load  is acting for a distance BC ;         P=2 kips/ft×6 ft ;P=12 kips…

Q: The rigid beam is supported at its ends by two A-36 steel tie rods. If the allowable stress for the…

A: τA=allowable stress for the steel=16.2 ksi ;load (w)= 3 kip/ft ;(x)= 4 ft ;

Q: The beam is constructed from three boards. Determine the maximum loads P that it can support if the…

A: Draw the free body diagram of the beam shown below.

Q: F12-6. Determine the slope of the simply supported beam at A. E = 200 GPa and I = 39.9(10) m*. 20 kN…

A:

Q: F12-9. The boards are bolted together to form the built-up beam. If the beamis subjected to ashear…

A: A=0.012×0.1A=0.0012 m2 y=0.075 m Now the value of "Q" can be calculated as…

Q: In each case, draw the estimated elastic curve: 4 m- 8 kN.m 2 kN/m 8 kN 4 kN

A:

Axial Load

When a bar of the uniform cross-section is acted by a load, such that the load acts along the longitudinal axis of the bar, such kinds of loadings are known as axial loadings. In general terms, a load is an external force acting on a component. An axial load acts perpendicular to the geometric cross-section of the component. Based on the direction of the application of the load, an axial load can be tensile or compressive. The analysis of bodies under the action of axial loads is generally studied under the branch of mechanics, known as statics.