9 - Forward path transfer function is applied to the input of a system with negative unit feedback as given below and the overrun rate at the output of the system is given as% OS = 7.8%. K G(s) = (s + 2)2 In this case, what is the peak time of the system?

9 - Forward path transfer function is applied to the input of a system with negative unit feedback as given below and the overrun rate at the output of the system is given as% OS = 7.8%. K G(s) = (s + 2)2 In this case, what is the peak time of the system?

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Related questions

Q: 24. The power of DSSS systems is largely in the spreading and dispreading of the received signal…

A: This question is based on the fill the blank. The power of DSSS systems is largely in the spreading…

Q: A scramble is a device that changes some of the signal's characteristics (e.g., frequency com-…

A: We will find out the output of multiplier then we will find out the output of LPF . We need to…

Q: A sinusoidal signal v (t) =20 Cos (2 nt) is transmitted using a 5-bit binary PCM system. The…

A: As per our company guidelines we are supposed to answer only first question kindly repost other part…

Q: 1) Upper cutoff frequency? 2) Lower cutoff frequency? 3) AV(mid)? 4) AV(300K)? 5) AV(200)? 6)…

Q: z(t) = G) sin(kat) k=0 This signal is sampled at the rate T = 0.2 sec/sample. Now, what happens if…

A: Given that xt=∑k=0512ksinkπtT=0.2sec/sample

Q: A heavily loaded line has the following parameters Before compensation: Ag =1<0° and Bg =200<90°…

Q: Problem7) Suppose that N(t) is a zero-mean stationary narrowband process. The autocorrelation…

A: GIVEN: (a) Rz(τ)=EZ*(t)Z(t+τ) (b) Rz(τ)=N0δ(τ) V=∫0TZ(t)dt…

Q: Q1) An analog signal is given by x(t)=sin(2000Ttt) what is the lower band on the sampling rate to…

A: Here signal is given we need to find sampling frequency

Q: Discuss the effect of adding zeros to overall transfer function on system response curve.

A: Zeroes: Zeroes of a transfer function are the frequencies (Value of s) for which the numerator…

Q: Q/A drawback of the integral gain Ki is that it can make the system alternate ups and downs since…

A: We are authorized to answer one question at a time, since you have not mentioned which question you…

Q: It is desired to set up a central station for simultaneous monitoring of the electrocardiograms ECGs…

A: Given data Signal bandwidth = 130 Hz Maximum acceptable error = 0.35% Calculating Nyquist rate…

Q: a) Find the value of when 1,0, and co No %3D b) Mark the region on the graph that been considered…

A: We know the relationship of channel Capacity :C=Blog21+SNfor error free transmission we know that…

Q: 1. Analyze the signal constellation diagram given below "00" "01" S. VE, (のn SA "11" "10" Identify…

A: Given: Analyze the signal constellation diagram given below: To find: Identify what modulation…

Q: (d) Sketch the spectrum of the sampled signal xs(t) when: = 1.5 Nyquist rate = 0.25 Nyquist rate а.…

A: Given the signal as shown below: x(t)=sinc2tπ d) We need to sketch the spectrum of the sampled…

Q: A system transfer function can sometimes be experimentally determined by injecting white noise n(t)…

Q: Q3: Determine the Nyquist rate of sampling required for the signal g(t)=e^(-2|t|) (Approximate the…

Q: Forthe followingtransferfunctions of control syste ms, determine the peak fre quency response gain,…

Q: Problem 5- If the second order system is sampled with periodicity T=0.5%, it will have poles r=0.6 ,…

Q: The integer number given by the ratio of the frequency of a harmonic to the fundamental frequency is…

A: A filter can be described in terms of engineering, computers, and signal processing, among other…

Q: Q. Given an analog signal x(t) = 3cos(2000t t)+ cos(8000tt), fort20 which is sampled at a rate of 6…

A: SAMPLING: It is a process in which a continuous time signal is converted into discrete time signal.…

Q: Q14) Given a DSP system in which a sampling rate of 8 kHz is used and the anti-aliasing filter is a…

A: Given, Sampling rate, fs = 8 kHz Cutoff frequency, fc = 3.2 kHz Order of the filter =? At the cutoff…

Q: 2.Discuss the effect of adding zeros to overall transfer function on system response curve.

A: Transfer function is basically the ratio of output to the input values. Here T(x)= Y(x)/ C(x) Where…

Q: 16. The spectrum of a lowpass signal is shown below: X(f) -1/30 Determine the value of the Nyquist…

Q: Q 2. Write the closed loop transfer function for the system shown below, determine the poles and…

Q: A signal s(t) is ideally sampled at a sampling rate (a) 15HZ, (b) 9Hz, (c) 10HZ. If the sampled…

A: a f=15 Hzfm=6 Hzfs+fm=21 Hzfs-fm=9 Hz No aliasing

Q: 13. Find the minimum required bandwidth for the base-band transmission of 4-level PCM pulses…

Q: 1. What is the minimum sampling frequency in Hz for the EEG signal with main components up to 10Hz?…

Q: Find the digital the equivalent transfer function for the following closed loop system where D(z) is…

Q: Compare between DSB-SC and DSB-LC modulation, considering total power and bandwidth.

A: DSB SC (double sideband with suppressed carrier) DSB LC (double sideband with carrier)

Q: a) Convert the analog voltage E(t) = 5 sin(2nt) mV into a discrete time signal and show your answer…

A: According to the question, we need to draw the discrete-time signal of the analog signal Et=5 sin2πt…

Q: Write a sample transfer function for a stable system with a closed cycle transfer function of 3rd…

A: According Routh Hurwitz stability criteria, If the first column elements of R H Table is of same…

Q: 2. Determine the range of sampling interval T, that will make the closed loop system shown below…

A: Steps: Find G(s) and then G(z) Then Using G(z) ,find T(Z) Find pole of T(z) Then range of T for the…

Q: The forward path transfer function of a unity feedback system is given by 100 G(s) = s? + 10s + 100…

Q: Consider a sinusoidal signal m(t) = Acos wmt applied to a delta modulator with step size A. Show…

A: Given data: A sinusoidal signal mt=Acosωmt is applied to a delta modulator The step size is ∆ The…

Q: It is desired to set up a central station for simultaneous monitoring of the electrocardiograms ECGs…

A: Bandwidth required by TDM scheme:BW=N*n*fsN: No. of users/Patientsn: No. of bitdFs: Sampling…

Q: Consider the system of Figure 7.1, where the input continuous-time signal „() has a band-limited…

A: For a system,The band limited spectrum Xa(jΩ) is shown below,

Q: The PAM sampling rate is not based on the Nyquist theorem. Select one: O True False

A: So we have to find whether the PAM signalling rate is based on Nyquist rate or not.

Q: [5] Let x[n] be discrete-time signal obtained from x (1) using sampling period T = 0.1 sec, and…

A: Given information: Sampling time T=0.1 s Expression of the signal is xn=1↑,0,-1,0

Q: using ideal sampling (impulses). At another location, the sampled signal is filtered by an ideal…

A: We need to find output signal for given sampler and bandpass filter

Q: Given L(s) = KG(s) s(s+10) (a) Find the value of K such that the maximum overshoot of the…

A: We need to find out the value of K then we will find out bandwidth for given system .

Q: Q3: Determine the Nyquist rate of sampling required for the signal g(t)=e^(-2|t|) (Approximate the…

Q: x(t) = 5 cos( 2n 3000t) + 5 cos(2n 6000t), for t 20, %3D Sampled at a rate of 12000 Hz, 1. Sketch…

Q: audio signal, band-limited to 300-→3300HZ, is sampled at the sampling rate 00 samples per second. If…

A: We need to find out number of bits and bandwidth for given pcm

Q: Problem 5- If the second order system is sampled with periodicity T=0.5%, it will have poles r=0.6 ,…

Q: 14) if the o/p of a feedback-type A/D is (101011) with clk freq.(1 MHZ) then Tconv. equals : 47 us…

A: 14) N= No of clock cycle required to get 101011 is decimal equivalent of this which is 43

Q: (a) What is the baud rate? (b) What is the equivalent bit rate? (b) What is the null bandwidth?

A: In this case, the gross bit rate will be According to the question, the number of possible values…

Q: SUBJECT IS : control system Q) Discuss the effect of adding zeros to overall transfer function on…

A: Given, Q) Discuss the effect of adding zeros to overall transfer function on system response curve.

Q: Discuss the effect of adding poles to overall transfer function on system response curve.

A: By adding poles in system transfer function. system become unstable and root locus of the system…

Q: Which claim is correct? If all the poles of a transfer function model have positive real part, then…

Question

9 - Forward path transfer function is applied to the input of a system with negative unit feedback as
given below and the overrun rate at the output of the system is given as% OS = 7.8%.
K
G(s) =
(s + 2)2
In this case, what is the peak time of the system?
A) 1.36 s
B) 1.58 s
C) 1.27 s
D) 1.15 s
E) 1.45 s

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Analysis of Multiple Order System and Steady State Error

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, electrical-engineering and related others by exploring similar questions and additional content below.

Similar questions

Open loop transfer function G(s) = K/ s(s+3)(s+4) for a system with a) Using the Routh Hurwitz criterion, the poles of the closed-loop system are only purely imaginary. Calculate the value of K for it to have roots on the axis. b) Calculate the maximum value of K for the system to be stable. c) Calculate the values of K for the system to have roots at the value of -1 on the real axis.
For a non -inverting operational amplifier, Rf = 80 kΩ , Ri = 6 kΩ fT = 2.35 MHz, Determine the closed loop lower critical frequency fc(cl) in kHz
Find the transfer function of the electric circuit given below by the block simplification method. In case of R = 1kΩ, C = 10µF and L = 2mH, if the system operates in closed loop with negative unit feedback, find out what the k value should be in order for the system to be stable.
"A common emiiter amplifier (Fixed Bias) is currently under test to determine its bandwidth in the unloaded case. In the bandpass region ,the amplifier's voltage gain, input impedance, and output impedance are measured to be 32dB, of 100k Ohms, and 3k Ohms, respectively. The designer used input and output coupling capcitors with values of 1uF and 100uF, respectively. The amplifier circuit's PCB layout was properly designed, thus minimizing the wiring capacitances. The device capcitances are measured as follows: C_BE = 1pF, C_BC = 8pF, and C_CE = 1pF. Assuming a voltage source resistance of 50 Ohms, determine the higher cutoff frequency due to the output circuit." 53.05MHz 5.77MHz 3.18MHz 9.72MHz
A common emiiter amplifier (Fixed Bias) is currently under test to determine its bandwidth in the unloaded case. In the bandpass region ,the amplifier's voltage gain, input impedance, and output impedance are measured to be 32dB, of 100k Ohms, and 3k Ohms, respectively. The designer used input and output coupling capcitors with values of 1uF and 100uF, respectively. The amplifier circuit's PCB layout was properly designed, thus minimizing the wiring capacitances. The device capcitances are measured as follows: CBE = 1pF, CBC = 8pF, and CCE = 1pF. Assuming a voltage source resistance of 50 Ohms, determine the higher cutoff frequency due to the input circuit
A common emiiter amplifier (Fixed Bias) is currently under test to determine its bandwidth in the unloaded case. In the bandpass region ,the amplifier's voltage gain, input impedance, and output impedance are measured to be 32dB, of 100k Ohms, and 3k Ohms, respectively. The designer used input and output coupling capcitors with values of 1uF and 100uF, respectively. The amplifier circuit's PCB layout was properly designed, thus minimizing the wiring capacitances. The device capcitances are measured as follows: C_BE = 1pF, C_BC = 8pF, and C_CE = 1pF. Assuming a voltage source resistance of 50 OhmsDetermine the higher cutoff frequency due to the output circuit
Find the binary transmission rate when a uniform analog signal with a bandwidth of 220Khz is converted into digital form using a uniform quantizer such that a practical system provides a signal-to-noise ratio (SNR) of at least 55 dB.
The front end of a television receiver, having a bandwidth of 7MHz and operating at a temperature of 27°C, consists of anamplifier having a gain of 15 followed by a mixer whose gain is 20.The amplifier has a 300-Ω, input resistor and a shot-noiseequivalent resistance of 500-Ω; for the converter, these values are2.2 and 13.5 kΩ, respectively, and the mixer load resistance is 470kΩ. Calculate Req for this television receiver.
3. What is the input-referred equivalent noise temperature of an amplifier having a gain of 20 dB and noise figure of 7.3 dB? What is the power spectral density of the noise produced by the amplifier, as measured at its output? Assume T0 = 290 K.
During a vibration measurement experiment in the Mechanical Engineering Department at Hacettepe University, a piezoelectric accelerometer output is given by this mathemtaical equation: a (t) = 1 + 4 sin(43.98t) + 7sin(100.53t) in gravity acceleration (g) value. a) Determine the frequencies (in Hz) contained in the signal. Round your results to nearest integer value. b) What is the minimum sampling rate to avoid aliasing? c) Sketch clearly the frequency spectrum if the signal is sampled at 15 Hz. d) Now, the signal is filtered with a low-pass Butterworth filter to remove the maximum frequency component. It is desired to attenuate the amplitude of this component to at least 5 % of its value. If the sampling rate is now 20 Hz, what will be the order of the filter? e) If the blue one is our signal, then what is red and green ones? Write down the mathematical relation between the three signals? (Use labels as blue, red and green signal.)
Design a radio receiver that powers an amplification system. The radio signal can be considered as an input voltage, while the amplification system, which is a two-terminal device, can be modeled as an equivalent resistance of 1 kΩ. A bandwidth of 500 kHz and a maximum power frequency of 10MHz are required.a) What is the quality factor?b) Do you consider that your receptor is selective or not very selective?
Ex. 1780. A closed-loop system has sustained oscillations (i.e. constant amplitude) with a period of 85 seconds when the gains are: proportional=96, integral=0, and derivative=0. Determine the ideal- PID gains Kp, Ki (minutes^-1), Kd (minutes) using the Ziegler-Nichols method. Also determine the standard-PID values which are commonly used in industry, such as LabVIEW: Kc, Ti (min), Td (min). ans:6