9. Consider 12 2 10 Ω a O 18 V 3Ω a. Find and draw the Thévenin equivalent circuit b. Find and draw the Norton equivalent circuit e. For the transfer of maxim um power, what load resistance should be connected across terminals a and b? d. What is the masimum power delivered to the load you calculated in Part c?

9. Consider 12 2 10 Ω a O 18 V 3Ω a. Find and draw the Thévenin equivalent circuit b. Find and draw the Norton equivalent circuit e. For the transfer of maxim um power, what load resistance should be connected across terminals a and b? d. What is the masimum power delivered to the load you calculated in Part c?

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter2: Fundamentals

Section: Chapter Questions

Problem 2.17MCQ: Consider the load convention that is used for the RLC elements shown in Figure 2.2 of the text. A....

See similar textbooks

Similar questions

The circuit given below will be analyzed. β=3 α=8 a) Norton in the form I = GNV + IN of the part of the circuit seen when looking left from the A-B ends find the equivalent (parametrically equivalent). b) Let R1 = 0.5Ω, R2 = 1Ω, J = 2A, E = 1V. 10Ω to A-B ends When the Ry load impedance is connected, the power consumed at this load is Norton for the circuit. Calculate using the equivalent.
As shown in the Figure , an external load resistor, R, is connected across the terminal a-b of the DC circuit. Based on Norton’s Theorem, calculate and analyse the circuit shown in the figure ( given V1=60V, V2=20V, R1 = 22ohm, R2 = 34ohm, R3 = 35ohm, R4 = 42ohm,) to determine the current, i, when R = 200 Ω
For the circuit shown if VS=j50VAC and V1=j30VACa) the node voltage a (va)b) The voltage of node b (vb) 0
Differential equation is given as- Vo(t) = Vdd(1- (R/(R+Ron))*e^(-t/RC)) a) Assume Ron=280 ohm. When the load capacitor is C = 0.5nF, the output must reach 90% of its final value by t = 25uS. Find a value of R that will satisfy this requirement while at the same time keeping the static power below 1 mW. For your chosen resistance, calculate how long it will take to reach the 90% level.
In the given DC circuit,a) Compute the open-circuit voltage (VOC) at terminals a-b by using node voltage method.b) Compute the short-circuit current (ISC) at terminals a-b by using mesh current method.c) Calculate the Thévenin (or Norton) equivalent resistance. (RT=Voc/Isc)d) Draw the Thévenin and Norton equivalent circuits.e) If a load is connected to terminals a-b, calculate the value of the load resistance for themaximum power transfer. Find the maximum power that can be delivered to the load. Note: Don’t use supernode or supermesh.Don’t use source transformation.
Analyze the:Figure Q2(a) Impedance seen by the source.(b) Coupling coefficient, K when angular frequency, ω = 4 rad/s .(c) Current through booth impedance 4 Ω, I1 and I2.
Which one of these network theorems states that any two-terminal linear bilateral dc network can be replaced by a current source and a parallel resistor? * a. Thevenin's theorem b.Superposition theorem c.Norton's theorem d.All
Find the Thevenin equivalent of the above circuit and calculate the load impedance that must be connected to terminals a-b for maximum power transfer. As a result of this calculation, what is the value of the current that will pass through your Thevenin equivalent circuit, depending on the ZL load impedance?
For the given circuit below, find the value of Vdc such that the current i0 = 0A. Use the methods of: a. Mesh Analysis b. Nodal Analysisc. Superposition d. Thevenin’s Theorem
α=4 β=4For the adjacent circuit, Vab=(400+5β)V is given and the source part is balanced. Since it is known as ZAN=j2α Ω, ZBN= 3α Ω and ZCN=-j3α Ω, calculate the value of the current Ib by its angle, ignoring the impedances of the transmission lines.Can you please post your solutions, it's very important
The load impedance in the figure absorbs 2.5 kW and generates 5 kVAR The sinusoidal voltage source develops 7.5 kW. Suppose that R= 16.5Ω A)Find the min and max of the two inductive line reactances that will satisfy these constraints. B)For Xminobtained in part A,find the magnitudes of the total reactive power generated and the total reactive power absorbed in the circuit. C)For Xmax obtained in part A,find the magnitudes of the total reactive power generated and the total reactive power absorbed.
The currents in each branch of a two - branched parallel circuit are given by expression i1 = 7.07sin(314t - π/4) A and i2 = 21.2sin((314t - π/3) A. The supply voltage is given by the expression v = 354sin 314t V. Determine the impedance Z1 and Z2. a. Z1 = 50.07 Ω, Z2 = 16.7 Ω b. Z1 = 35.4 Ω, Z2 = 8.35 Ω c. Z1 = 10.0 Ω, Z2 = 10.2 Ω d. Z1 = 14.46 Ω, Z2 = 14.14 Ω