9. Show that In an a.c. olrcult maximum power is transferred to a load whose Impedance is equal to the conjugate of the Thevenin's Impedance of the circult as seen across the load terminals. If the load consists of only a resistance and no reactance what should be the magnitude of the resistance for maximum power to be transferred to It? Determine.

9. Show that In an a.c. olrcult maximum power is transferred to a load whose Impedance is equal to the conjugate of the Thevenin's Impedance of the circult as seen across the load terminals. If the load consists of only a resistance and no reactance what should be the magnitude of the resistance for maximum power to be transferred to It? Determine.

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter2: Fundamentals

Section: Chapter Questions

Problem 2.22P: The real power delivered by a source to two impedances, Z1=4+j5 and Z2=10 connected in parallel, is...

See similar textbooks

Similar questions

For the circuit shown in Figure,a. Find the Thévenin equivalent circuit for the source.b. Find the power dissipated by the load resistor. c. What value of load impedance would permitmaximum power transfer?The voltage source is sinusoidal with frequency60 Hz, and its polarity is such that the current fromthe voltage source flows into the 10-Ω resistor.
A power station is to supply two loads. The daily load curve of the station is as shown in figure below. If the load factor of the two loads are 0.416 and 0.458 respectively, and the diversity factor of the power station is 1.142, find:1- The load factor of power station.2- The energy consumed per day and the maximum demand(connected load) of each load.
When it is connected in series with a pure resistor R with resistance r and inductance L, the current it draws with a sinusoidal voltage application with an effective value of 100V is 5A. The voltage across the coil and resistor element is 80V and 30V. a-Find the power and power factor consumed by the coil alone? b- Find the power consumed by the system and the power factor? c- Draw the voltage triangle, impedance triangle and power triangle?
A symmetrical T-network has a resistance of 750Ω in the series arm and250Ω at each shunt arm. Find (a) open circuit and short circuit impedances,(b) characteristic impedance, (c) propagation constant.
A balanced positive-sequence wye-connected 60-Hz three-phase source has line-to-line voltages of VL = 440 V rms. This source is connected to a balanced wye-connected load. Each phase of the load consists of a 0.5-H inductance in series with a 30-Ω resistance. Assume that the phase of VanVan is zero. FIND Ia,Ib,Ic, Find the power delivered to the load And Find the reactive power delivered to the load.
A 60-Hz 240-V-rms source supplies power to a load consisting of a resistance in series with an inductance. The real power is 1500W, and the apparent power is 2500 VA. Find the impedance and power factor in the system.
What is voltage stability? How is reactive power linked with the voltage stability in the power system? Write down the effect of ‘Load Tap Changer (LTC)’ on voltage stability and analyze very briefly using P-U (nose) curve.
1- When connected in series with a pure resistor R with resistance r and inductance L, three pairs of currents are 5A with a sinusoidal voltage application with an effective value of 100V. The voltage across the coil and resistor element is 80V and 30V. a-Find the power and power consumed by the coil alone? b- Find the power consumed by the system and the power factor? c- Draw the voltage triangle, impedance triangle and power triangle?
Using the circuit above, determine the complex power of the source and the power factor of the voltage source, give the following: (show your work and up load it to Q21) v(t) = 12cos(200t) V, R = 20 Ω, and C = 4.7 μF
This is not a graded assignment. Its a mock exam. I need help with both parts of the question: my current apporach thinking is that. To find the maximum average power transfer to the load I know we would first find the Impedance values of all the components and than add them up and than finally find the conjugate of that value correct? But im not sure how to find Pmax than based on what i got for part 1. Some guidance here would be appreciated. Im also not sure if my part 1 is correct either so i would apperciate assitance on that question as well
For the following network find a) Isb) PT, QT, ST and PFTc) Draw power triangle d) Raise the power factor to unitye) Compute Is after raising the power factor
(a) What is leading and lagging power factor? and discuss about the reasons for the low powerfactor.(b) Discuss about the power factor improvement methods