9. What are the nominal and actual depths of a W16×100 wide-flange member? What is the weight of this member per linear foot? (Hint: Use your AISC Manual.)

Q: Solve for the force in the marked members in each truss. a 4@4 m = 16 m b 12 kN 2 m 3 m

A: Multiple questions As per our guidelines we are supposed to answer only one question. Kindly repost…

Q: From your Atterberg limits tests on the -40 portion of these samples, you have obtained the…

A: Given,

Q: Determine the reactions and the force in each member of the space truss. Indicate if the members are…

A: Given:- A space truss is given  The magnitude of the force at point D = PY = 500 lb To determine:-…

Q: Small-diameter, high-pressure liquid jets can be used to cut various materials as shown in the…

A: Using Bernoulli's equation

Q: Q. 13. describe various force acting on dam?

A: solution of above problem is below:

Q: View Policies Current Attempt in Progress Water flows over the spillway shown in the figure below.…

A:

Q: A clayey soil with specific gravity of 2.70 has natural moisture content of 16% at 70% degree of…

A: Given data- Specific gravity G=2.7, water content w=16%, Degree of saturation S1 =70%, Degree of…

Q: Q- An automobile with projected area 2.6 m² is running on a road with a speed of 120 km per hour.…

A: Given data: Area, A = 2.6 m2 Speed, v = 120 km/hr = 33.33 m/sec Mass density, ρ=1.2 kg/m2 Kinematic…

Q: (Bernoulli/continuity) Water flows into a large tank at a rate of 0.011 m³/s as shown in the figure…

A:

Q: Use the method of joints to find all reaction and member forces in the trusses. (1-b) 3 kN 4 m 4 m…

A: Multiple Sub- parts As per our company guidelines we are supposed to answer only first sub-parts.…

Q: need help with the vectors A,B,C,D in their Cartesian form, I started A but I am unsure if it is…

A:

Q: 7. Given the mass of 1.500 Mg and a volume of 2.205 x 10^6 cc, what is the specific gravity? * 0.685…

A:

Q: The cable supports the loading shown. Determine the magnitude of the vertical force P so that y = 4…

A:

Q: Find the Normal force if friction force is 444 N and coefficient of friction is 0.37

A:

Q: 5. The homogeneity of the chloride level in a water sample from a lake was tested by analyzing…

A:

Q: Please answer part A again with step by step. Dont give direct table. it is not at all…

A:

Q: A beam 100 mm wide is to be loaded with 20 kN concentrated loads spaced uniformly at 0.40 m on…

A:

Q: How is reduction factor for large building calculated to determine internal pressure coefficient?…

A: Internal pressure coefficient shall be multiplied with the reduction factor while designing large…

Q: HYDROLOGY •• SUMMARIZE THE PROCESS ON HOW TO COMPUTE AREAL PRECIPITATION USING 4 METHODS *ARITHMETIC…

A:

Q: 2. From the following data taken from 4 vehicles observed from photographs taken 2 seconds apart,…

A:

Q: 17. At 32 deg. celcius and 308 KPa absolute, the specific weight of a certain gas is 13.7 N/m^3.…

A: Given data,  Temperature, T = 32°C  = 32+273 = 305 K  Pressure , P = 308 KPa = 308 × 103 Pa…

Q: A machine component is subjected to the forces shown, each of which is parallel to one of the…

A:

Q: Q-A precast concrete pile is driven with a 50 kN hammer falling through a height of 1.0 m with an…

A:

Q: Water flows under the sluice gate shown in the figure below. Determine the flowrate if the gate is…

A:

Q: A typical hospital floor in a seven-storybuilding is composed of a 300mmthick slab resting on steel…

A:

Q: A pressure-vessel is fabricated by gluing the circular plate to the end of the vessel as shown in…

A: Internal pressure = P = .45MPa Diameter = d = 450mm Thickness = t = 10mm Side thickness = t' = 20mm

Q: A tape was suspended in four spans under a pull of 14.78 kg and mean temperature of 14°C. Each span…

A:

Q: Find the total deformation in the figure shown below if Est = 200 kN/mm², EAL=200 kN/mm² AL 60KN…

A: Finding axial deformation

Q: Q-A pre-tensioned concrete member of section 200 mm x 250 mm contains tendons of area 500 mm² at…

A:

Q: Current Attempt in Progress Water flows steadily with negligible viscous effects through the pipe…

A:

Q: A simple log bridge in a remote area consists of 2 parallel logs with planks across them. The log…

A: Given data, Simply supported beam with plank resting on two logs The span of the bridge, l = 2.5 m…

Q: 10. Given the specific gravity of oil is 0.85, what is the density in slugs/ft^3?

A: CONCEPT: Specific gravity is defined as the ratio of density of particular fluid to the density of…

Q: X 4 m 3 kN/m 3 m 50 KN 3 m AB 4. A steel beam with EI = 16 × 106 N. m² is loaded as shown in figure.…

A: Given  EI= 16×106 N.m2

Q: beam 20 m long is loaded as shown in Figure below. The supports am e reaction is the same at each…

A: We need to find X1 and X2 Conditions : R1=R2 Moment about supports =0 Equilibrium of forces

Q: Given how much material is crammed into the school day, are these breaks realistic?

A: Achieving productivity, achievement, and optimism about the future requires taking a brief break to…

Q: 2.15 Compare the following three roof structures. All three have the same span length and the same…

A:

Q: (a) What is meant by "Canal falls"? Why are canal falls constructed in a canal system? Draw a neat…

A:

Q: Current Attempt in Progress Oil flows through the system shown in the figure below with negligible…

A:

Q: 3m A ● • Analyze the simple truss shown. H B 6KN 4m 4m tam tam C 7KN 4m + th 8KN f Am f 4.5m

A:

Q: Solve for the hydraulic design of an irrigation canal in clayey alluvial soil as per Kennedy's…

A: Given- An irrigation canal in clayey soil with parameter as follow discharge=60cumecrugosity…

Q: Q3: A: FILL THE BLANKS WITH APPROPRIATE WORD: 1- The main oxides of cement are 2- Setting of cement…

A: Due to company's guidelines we can only answer first three questions Kindly post other questions as…

Q: QUESTION #2 A rectangular foundation (B x 1.2B) has to be constructed as shown in Figure. Assume…

A:

Q: A column is supported on a footing as shown in the figure below. The water table is at a depth of 1…

A: Given figure of a column: Factor of safety = 3, Area, A = 1.5 m × 3 m = 4.5 m

Q: (Bernoulli/continuity) Water flows steadily through the pipe shown in the figure below such that the…

A: Assuming,  Water is incompressible and steady. Given data, P1 = 262kPa P2 = 116 kPa D1 = 0.11 m V1…

Q: Referring to the figure below, considering the speed of vehicle V1 is 60 km/h, the speed of vehicle…

A: Given : Speed of vehicle 1 is V1 =  60 km/h Speed of vehicle 2 is V2 =  40 km/h Relative speed of…

Q: The eye bolt is used to support the load of 5 kip. Determine its diameter d to the nearest 1/8 in…

A: Given data:- The given load is, =5 kip τallow=5 ksi. σallow = 21ksi

Q: Water flows through a 100 mm diameter pipe with a velocity of 0.015 m/sec. If the kinematic…

A: Given- Pipe diameter D=100 mm, Velocity V=0.015 m/s, kinematic viscosity- v=1.13×10-6 m2/sec,

Q: Please do all questions thank in advance.

A: "Since you have posted a question with multiple sub-parts, we will solve first three sub parts for…

Q: 1. List the limitations of the direct design method. 2. Define the equivalent column. 3. Show how to…

A: The direct design strategy is a scientific methodology by which the necessary area of support for…

Q: Draw the shear force and bending moment diagram for the compound beam shown in the figure. Assume…

A:

Bars

In civil engineering, bars refer to steel reinforcement bars or rebars. These are structural members primarily used for reinforcement purposes in masonry works. A bar is characterized by its cross-sectional area, which is negligible compared to its length. Bars are usually manufactured by steel which is uniform throughout the length, or by meshing multiple steel wires. Other materials of the bar include carbon steel, glass fiber, carbon fiber, and basalt fiber. The reinforcing bars are coated with epoxy resins and other materials to enhance some of their properties including corrosion resistance.