9. Write a sequence of LEGV8 instructions to do the following: set X8 to 100 if the contents of X1 is an odd number and set X9 to 200 otherwise. Do not use division instruction in you code. Instead, you use an AND instruction to test if a number is even or odd. Comment your assembly code. 10. Write the corresponding LEGV8 code for the following fragment of C code for ( int į=0; i< 50; i+) C =C[i-1]-C[i+1]*9; Assume that the index i is in register X0, C is an integer array and the base address ofC is in X2. Comment your assembly code. How many instructions are executed? How many data memory references have been made? I

9. Write a sequence of LEGV8 instructions to do the following: set X8 to 100 if the contents of X1 is an odd number and set X9 to 200 otherwise. Do not use division instruction in you code. Instead, you use an AND instruction to test if a number is even or odd. Comment your assembly code. 10. Write the corresponding LEGV8 code for the following fragment of C code for ( int į=0; i< 50; i+) C =C[i-1]-C[i+1]*9; Assume that the index i is in register X0, C is an integer array and the base address ofC is in X2. Comment your assembly code. How many instructions are executed? How many data memory references have been made? I

Database System Concepts

7th Edition

ISBN:9780078022159

Author:Abraham Silberschatz Professor, Henry F. Korth, S. Sudarshan

Publisher:Abraham Silberschatz Professor, Henry F. Korth, S. Sudarshan

Chapter1: Introduction

Section: Chapter Questions

Problem 1PE

See similar textbooks

Similar questions

W rite a MIPS program to continuously generate the following series of integers: 1, 2, 3, 6, 9, 18, 27, 54, 81, and so on. Use standard MIPS programming conventions. Use the jump instruction to generate an infinite loop. Write a subroutine EVEN that returns a 1 if the argument is even, else it returns a 0. You must call this subroutine with jal and return from it with jr. Dont use any .data, .word, .text, or .globl commands or li. No hand written and fast answer with explanation
[Note: You are allowed to use only instructions implemented by the actual MIPS hardwareprovided in attached photos below. Use assembly language format from the references orthe book. Note, base ten numbers are listed as normal (e.g. 23), binary numbers areprefixed with 0b and hexadecimal numbers are prefixed with 0x.] Write a C program and corresponding assembly program based on MIPS ISA that reads three edges for a triangle and computes the perimeter if the input is valid. Otherwise, display that the input is invalid. The input is valid if the sum of every pair of two edges is greater than the remaining edge. [Direction: You can consult any resources such as books, online references, and videosfor this assignment, however, you have to properly cite and paraphrase your answerswhen it is necessary.] solve it any how urgently please.
15)The execution potion of the LOAD instruction starts with the _. a. going to the mailbox address specified in the instruction he previously read b. reading the number in the mailbox with the address given by the location counter c. going to the mailbox with the address given by the location counter d. fetching the address from the location counter
8.fast please in assembly You are giving the before condition and an instruction. Give the after condition:Before:Esp:00 63 FB 54instruction: ret After: Group of answer choices esp: 00 63 FB 50 esp: 00 63 FB 55 esp: 00 63 FB 54 esp: 00 63 FB 58
25: . Find the time delay in the following program if the crystal frequency is 1 MHz. Do not ignore the time delay due to the first and last instruction. DELAY: LDI R16, 30 AGAIN: LDI R17, 35 HERE: NOP NOP DEC R17 BRNE HERE DEC R16 BRNE AGAIN RET 26: Write a program to display 2 on 7 segment. A 7 segment is connected to PortD.
If R1 contains ×FFFF and R2 contains ×0000, then what are the condition code values after the following instruction is executed? 0001 011 001 0 00 010 A) N is [ 0 or 1]? B) Z is [ 0 or 1]? C) P is [ 0 or 1]?
FILL IN THE BLANKS ? (8) After the instructions MOV AX, 2500H and ADD AX, 2300H have been executed in sequence, find the status of SF= 【16】, AF= 【17】 and ZF= 【18】.
Rearrange the following code to minimize the total number of cycles, assuming that a dependent instruction following the load will need two clock cycles of delay before getting the data. Load r1, 64 (r2)Add r2, r2, r2Sub r3, r4, r1Load r4, 32 (r4)
1a. determine its function 1b. If the instruction JZ is replaced by JNZ, modify the program so that you can obtain the same result.
Implement the following high-level code segments. Assume the integer variables g ,h ,m ,and r are in registers $s0 and $s1, $s2, $s3, respectively.if (g == h)r =g +h+m;elser =g *h-3;
What is the following instruction equivalent to? addiu $t2, $t3, 7 A. $t2 + $t3 = 7 B. $t2 = $t3 & 7 C. $t2 = $t3 + 7 D. $t3 = $t2 + 7
Computer Science Encode the following instruction from MSP430 assembly to MSP430 machine code. You will have to put Byte 0 in the first blank, byte 1 in the second, and so on. Note you do not need to write 0x, it is assumed the entered values are hex bytes. mov #17794, r14 Byte 0 Byte 1 Byte 2 Byte 3 0x 1. 0x 2. 0x 3. 0x 4.