Hand written solution not allowed 9.3-23 The beam shown in the figure has a slidingsupport at A and a roller support at B. The slidingsupport permits vertical movement but no rotation.Derive the equation of the deflection curve anddetermine the deflection 8 at end A and also c atpoint C due to the uniform load of intensity q = P/LL/3. Useapplied over segment CB and load Patxthe second-order differential equation of the deflec-tion curve.yAL3L12PCP9= LL121BX

Draw FBD:Calculate Bending moment equation:

9.3-23 The beam shown in the figure has a support at A and a roller support at B. The support permits vertical movement but no r Derive the equation of the deflection cu determine the deflection 8, at end A and al point C due to the uniform load of intensity q applied over segment CB and load Pat x = L the second-order differential equation of th tion curve. y A L 3 P C 9 = P L B

9.3-23 The beam shown in the figure has a support at A and a roller support at B. The support permits vertical movement but no r Derive the equation of the deflection cu determine the deflection 8, at end A and al point C due to the uniform load of intensity q applied over segment CB and load Pat x = L the second-order differential equation of th tion curve. y A L 3 P C 9 = P L B

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Circular beam with modulus of elasticity E=70 GPaA distributed load of 35 kN/m and a bending moment of k⨯2.3 kNm are applied. Using the analytical (integral) method;a) Determine the support reactions and the moment of inertia of the section.b) Moment function and 2nd order differential equation c) Boundary conditions, slope and deflection equationsd) the angle of inclination at point B (2),e) Determine the deflection (3) at point C.K=1.85 D (mm) L (m) k⨯87 k⨯1.5
From the beam shown. Let P = 40 kN, Q = 4 kN/m, L =8m. Determine: 1. Reaction at A. 2. Constant C1. 3. Slope at L/3. 4. Deflection at L/3.
Two steel pipe columns (E=200,000??a,A1=2000mm2,A2=1800mm2)support a rigid beam AC that has a 3.6m overhang BC. The beam supports a linearly varying load of maximum intensity w=75K/nm as shownin the figure.Neglect the weight of the beam AC, and assume that the beam is supported on the two columns such that it transmits load to each column as an axial load.Determine the vertical displacementat end C of the beam, in column 1at A and column 2at B. Answer in mm.
determine the vertical reaction at B in kN using any Geometric Method. Consider 250 mm x 400 (b x h) mm section and E = 100,000 MPa. Enter the absolute value only and round-off your answer to 3 decimal places
The 426-kg uniform beam is subjected to the three external loads shown. Compute the vertical reaction (N) at the support point O if P = 4189 N, Q = 3243 N, T = 40187 Nm, x = 1.02 m, y = 1.43 m, and z = 1.56 m and the system is in equilibrium.Positive values are to the right, up, and counterclockwise. Round off only on the final answer expressed in 3 decimal places.
Use Area-Moment Method. Consider 150 mm x 150 mm section and E = 80 GPa. A=2.8 B=24.0 C=28 Determine the following: Vertical Reaction at B in kN. Moment Reaction at A in kN-m.
EI is constant (Assume EI= 1 kN-m^2) use moment area method 1.) determine the location of the maximum deflection from A2. ) determine the maximum deflection
3.) For the given couple-force system shown, determine the horizontal component of Q. P= 335 KN Q= 44 KN R=74 KN-m Z=263 KN
The beam AB, shown in Figure 1a, with length L = 4.5 m is subjected to a uniform distributed load w = 13 kN/m and a concentrated moment M = 18 kN.m applied at point B. The beam has a rectangular cross-section with height h = 183 mm, width b = 98 mm, and constant thickness t = 12.5 mm as shown in Figure 1b. Take E = 200 GPa. 1. Determine the moment of inertia of the cross section .2. Determine the slope at point B
In the cage system below; It is under the effect of a P=250 kN load acting at an angle of θ=30° from the point C. Calculate the horizontal displacement (cm) to the right at point C. (E=2000 kN/cm² and A=50 cm² will be taken for all bars.)
The block A and the wedge B weighs 100 kN and 40 kN, respectively. The coefficient of fritction for all contacting surfaces is µ = 0.268. Determine the following: a. What value of P in kN would be required to push to the right the wedge under the block? b. What value of P in kN would be required to pull to the left the wedge under the block? Assume the block A is stll in contact with the wall just as motion starts.
c. Slope at L/3. d. Deflection at L/3