9.4 A steel cylinder 1 m long, of 150 mm internal diameter and plate thickness 5 mm, is subjected to an internal pressure of 70 bar (7 MN/m2), the increase in volume owing to the pressure is 16.8 x 106m. Find the values of Poisson's ratio and the modulus of rigidity. Assume E= 210 GN/m2. [0.299; 80.8 GN/m2] %3D

9.4 A steel cylinder 1 m long, of 150 mm internal diameter and plate thickness 5 mm, is subjected to an internal pressure of 70 bar (7 MN/m2), the increase in volume owing to the pressure is 16.8 x 106m. Find the values of Poisson's ratio and the modulus of rigidity. Assume E= 210 GN/m2. [0.299; 80.8 GN/m2] %3D

Principles of Heat Transfer (Activate Learning with these NEW titles from Engineering!)

8th Edition

ISBN:9781305387102

Author:Kreith, Frank; Manglik, Raj M.

Publisher:Kreith, Frank; Manglik, Raj M.

Chapter3: Transient Heat Conduction

Section: Chapter Questions

Problem 3.4P

See similar textbooks

Similar questions

A tensile test is conducted on a mild steel bar. The following data was obtained from the test : diameter of the steel bar= 3cm, Gauge Length of the bar = 20cm, Load at Elastic limit= 250kN, Extension at a load of 150kN= 0.21 mm, Maximum Load = 380kN, Total Extension= 60mm, Diameter of the rod at failure=2.25cm, determine young's modulus?
A sectional steel cable of 3.00 cm2 has a mass of 2.40 kg per meter. If the cable is 500 m long hanging on a vertical cliff, how far the cable is stretched due to weighs itself? Known young steel modulus 2.00 x 10¹¹ N/m2 . (b). If there are two climbers hanging on the cable, determine how far cable is stretched. The mass of climbers is 60 kg and 70 kg, respectively.
A board of mass mand length l is attached to a wall and a rope that makes an angle of theta, as shown. A block of mass M hangs from the right end of the board. Suppose m = 2.0kg, L = .60m, M = 0.50kg, and angle(theta) = degrees. a. Using numbers, what is the magnitude of the tension force in the rope connecting the board and wall? b. Using numbers, what is the magnitude of the force applied by the hinge? c. Using numbers, in what direction does the force applied by the hinge point?
Give an approximate value for the tensile strength of a Boron/Aluminum composite with Vf = 0.4. Aluminum 2024 has E = 71 GPa, Poisson = 0.334, yield strength Sy = 76 MPa, strain-to-failure Ey = 22%. Boron fibers have E = 400 GPa, strength = 3.4 GPa, Poisson = 0.25. a. Compute F1t, assuming the Aluminum matrix remains elastic up to failure. If the value found is larger than Sy, the matrix yields, thus invalidating the assumption. b. Recompute using O1 = VfOf + (1 - Vf)Om c. Check that the strain-to-failure is not exceeded.
A sheet metal cutting machine cuts the sheet metal via shear force, V as shown in Fig. 1. The crosssection of sheet metal is rectangular with width, b = 3m and thickness, d = 5mm. The sheet metal ishaving yield strength σy = 220 MPa; Young’s modules, E = 200 GPa and Poisson’s ratio, ν = 0.3.Conduct the following analyses at the state of stress when maximum stress reaches σy and beforeshearing commences. (Need answer Question c) & d) c. Sketch the YIELD LOCI for both cases above. d. As a sheet-metal engineer, which failure criterion in (b) will you use to determine the cuttingshear force? Explain the reason for your answer.
um and steel pipes are fastened to rigid supports at ends s for the following data: The cross:sectional area of aluminum pipe A, = 8.92 in?, cross-sectional area of Stei & modulus of elasticity of aluminum E, = 10 x10° psi, and modulus of elasticity of
7.10 A rigid bar is suspended by three equally spaced wires of equal length. Theouter wires are steel and are 2 mm in diameter, the centre wire is copper andis 5 mm in diameter. If the weight of the rigid bar is 2,25 kN, calculate the loadcarried by each wire. If the temperature of the system is now raised by 90 °C, what will the magnitude and nature of the resultant stresses set up in the steeland copper wires be. (Let EST = 200 GPa; Ecu = 100 GPa; aST = 12 x 10_6/°C;acu = 18 x 10-6/°C?)
2. Ships and sailing vessels often carry lead ballast in various forms, such as bricks, to keep the ship properly oriented and upright in the water. Suppose a ship takes on cargo and the crew jettisons a total of 0.500 m3 of lead ballast into water 2 000 m deep. Seawater's density is equal to 1.025 g/cc while lead's bulk modulus equals to 42.0 GPa. Calculate the weight of water in a column with cross section of 1.00 m2. 20.1 MN 22.1 GN 21.1 MN 21.1 GN 22.1 MN 20.1 GN Find the change in the pressure at 2.0 km depth. 21.1 MPa 21.1 GPa 20.1 GPa 22.1 MPa 20.1 MPa 22.1 GPa Find the change in the volume of the lead at 2.0 km depth. -0.000 30 cubic meter -0.000 28 cubic meter -0.000 24 cubic meter -0.000 26 cubic meter -0.000 34 cubic meter -0.000 32 cubic meter
A materila has a modulus of elasticity (E=17 Mpa) and a poissons ratio of 0.27. what is the approximate value of the shear modulus, G?
A copper rolled wire 10 m long and 1.5 mm diameter when supporting a weight of 350 N elongates 18.6 mm. Compute the value of the Young's modulus of this wire
A straight bar of uniform cross sectionis tested in tension. The bar's cross sectional is 6.5 square centimeters and a length of 4 m. When the tensile load reaches 85kN, the total elongation is 2.5mm. What is the stress and the modulus of elasticity of the bar?
a. An overhead line has the following data: Span length= 160 m Conductor diameter= 0.95 cm Weight per unit length of the conductor= 0.65 kg/m Ultimate stress= 4,250 kg/cm2 Wind pressure= 40 kg/m2 Safety factor= 5 Calculate the sag? b. Derive the expression for the lowest point of the catenary curve if the supports are at different levels. Given that weight of conductor= 0.35 kg/m. Maximum allowable tension= 800 kg. Span length= 160 m and safety factor = 2. Find minimum point of catenary if supports are at 70 m and 60 m.