A 0.5 m x 2 m flat plate is towed at 5 m/s on a 2-mm-thick layer of SAE-30 oil at 38°C that separates it from a flat surface. The velocity distribution between the plate and the surface is assumed to be linear. What force is required if the plate and surface are horizontal? 1.4

A 0.5 m x 2 m flat plate is towed at 5 m/s on a 2-mm-thick layer of SAE-30 oil at 38°C that separates it from a flat surface. The velocity distribution between the plate and the surface is assumed to be linear. What force is required if the plate and surface are horizontal? 1.4

Principles of Heat Transfer (Activate Learning with these NEW titles from Engineering!)

8th Edition

ISBN:9781305387102

Author:Kreith, Frank; Manglik, Raj M.

Publisher:Kreith, Frank; Manglik, Raj M.

Chapter5: Analysis Of Convection Heat Transfer

Section: Chapter Questions

Problem 5.24P: Engine oil at 100C flows over and parallel to a flat surface at a velocity of 3 m/s. Calculate the...

See similar textbooks

Related questions

Q: A ship is 180 m long and has a wetted area of 8000 m2. Estimate the power expended against drag when…

Q: Air at 20 °C flows at V = 10 m/s over a flat plate of length L= 1.52 m and width W = 2 m. Calculate…

A: Given: The velocity of the air, V = 10 m/s length of the plate, L = 1.52 m The width of the plate, W…

Q: Consider the lifting flow over a circular cylinder of a given radius (R) and with a given…

Q: A particle of 2 mm in diameter and density of 2500 kg/m3 is settling in a stagnant fluid in the…

Q: The wing of the Fairchild Republic A-10A twin-jet close-support airplane is approximately…

A: Reynold's number: It is a dimensionless number it is the ratio of the inertia force to the opposing…

Q: Water flows at a velocity of 1.2 m/s over a flat plate 1.2 m long. Assume 1/7th power law and…

Q: Two large fxed parallel planes are 12 mm apart. The space between the surfaces Example is filled…

Q: The standard sea level value of viscosity coefficient for air is μ = 1.7894×10−5 kg/(m · s) = 3.7373…

A: Given data: *The standard level value of viscosity coefficient of air is μ = 1.7894×10−5 kg/(ms)…

Q: A flat plate has been placed longitudinally in a stream of crude oil which flows with a velocity of…

A: “Since you have posted a question with multiple subparts, we will solve first three sub parts for…

Q: A space of 25 between tWo surraces th SAF west lubricating oil at 250C (u = 0.18 Ns/m?). Plot the…

Q: A laminar boundary layer is observed to grow on a flat plate such that the pressure is constant…

A: Write the expression for displacement thickness.

Q: We are testing a flat plate of length L = 1.125 m and width W = 0.225 m in a stream of air flowing…

A: For flat plate boundary layer conditionWe Re=5×105Thus Re=ρVLμ Re=1.2×20×1.12518×10-6 Re=15×105Thus…

Q: 5.7 The rectangular roof sheet of a kennel has a dimension of 6m x 2 m. Calculate the drag force on…

Q: explain the effect of aerodynamic drag and lift on aerofoils

A: As an aircraft's speed increments, drag on the flying machine generally increments much speedier.…

Q: A square block weighing 1.1 kN and 250 mm on an edge-slides down an incline (20° with horizontal) on…

Q: 1.7 A 90 N rectangular solid block slides down a 30° inclined plane. The plane is lubricated by a 3…

Q: A fluid with viscosity of u = 1.752 x 10-5kg/m. s and density of p= 1.2kg/m³ %3D flows at U=1 m/s…

A: We have to determine (a) Find the boundary layer thickness at the end of the plate. (b) Find the…

Q: m/s support

Q: Engine oil at 40°C flows over a 20-m-long & 3-m-wide smooth flat plate with a free-stream velocity…

Q: Air at 20 °C flows at V = 10 m/s over a flat plate of length L= 1.52 m and width W = 2 m. Calculate…

A: Boundary layer thickness is the distance from the plate in a vertical direction up to where velocity…

Q: 1) For a parallel laminar flow over flat plates, the friction coefficient depends only on the…

A: Solution:

Q: FLUID MECHANICS 0.5m by 2m flat thin plate is moved at 5m/s on a 2-mm thick layer of SAE30 oil at…

Q: Q.5. For the velocity profile in laminar boundary layer: 13 3 2 2 Find the thickness of boundary…

Q: 2- Oil with a free stream velocity of 2 m/s flows over a thin plate 2m wide and 2m long. Calculate…

Q: 2. Water flows at a velocity of 1.2 m/s over a flat plate 1.2 m long. Assume 1/7th power law and…

Q: 1.7 A 90 N rectangular solid block slides down a 30° inclined plane. The plane is lubricated by a 3…

Q: A stationary sphere in water moving at a velocity of 2.3 m/s experiences a drag of 6N. Another…

A: Given data,

Q: e. A 0.5m x 2m flat plate is towed at 5 m/s on a 2-mm-thick layer of SAE-30 oil at 38°C that…

Q: A thin fl at plate 55 by 110 cm is immersed in a 6-m/s streamof SAE 10 oil at 20°C. Compute the…

A: Given: The area of the thin flat plate is A=55 cm×110 cm. The velocity of the oil is V=6 m/s. The…

Q: Q2:B) Calculate the power required to pull (1.5m x 1.5m) flat plate at speed (1 m/s) to the left…

A: Given data Dimensions of plate = 1.5 m x 1.5 m Speed of flat plate = 1 m/s Horizontal spacing = t =…

Q: A minivan is pulled by a tow truck at 60 kph. The boxlike van is 20m long, 6m high, and 3.75m wide.…

A: Given Velocity, v = 60 km/h = 16.67 m/s Length, L = 20 m Density = 0.0023 kg/m3…

Q: Air at 20 °C flows at V = 10 m/s over a flat plate of length L= 1.52 m and width W = 2 m. Calculate…

A: Air temperature, T=20oC Air speed, V=10 m/s Length of the flat plate, L=1.52 m Width of the plate,…

Q: Problem 1. For uniform flow over a flat plate, a useful approximation for the z-component of…

A: Given the profile uU=2yδ-yδ2δ=cx12

Q: Outside an inner, intense-activity circle of radius R , a tropicalstorm can be simulated by a…

A: (a) Given velocity potential function is The tangential velocity can be determined as,

Q: a. What is a favorable pressure gradient? What is an adverse pressure gradient? b. What is boundary…

A: “Since you have posted multiple, we will solve the first question for you. To get the remaining…

Q: A 0.5m x 2m flat thin plate is moved at 5m/s on a 2-mm thick layer of SAE 30 oil at 38 degrees…

A: This question is related to the newton law of viscosity. According to this question, the velocity…

Q: B) Calculate the power required to pull (1.5m × 1.5m) flat plate at speed (1 m/s) to the left side…

Q: Q4) Define the boundary layer, then find the thickness of boundary layer, shear stress, drag force…

Q: (b) In an experiment to compare the viscosities of two oils, small spheres are allowed to fall…

A: Solution:

Q: Sand particles (SG = 2.7), approximately spherical withdiameters from 100 to 250 μm, are introduced…

A: From Stole's law, we know that settling velocity (Vt) is given by : Vt = (2/9) * g * (⍴sand -…

Q: fluid mechanics explain, with examples, the effects of temperature and shear forces on newtonian…

Q: A thin flat plate 20 cm by 90 cm is immersed in a 1m/s stream of water at 20 °c ( density=998,…

A: Given data: The velocity of fluid over the plate is, v=1 ms The density of water at given…

Q: plate 450 mm x 150 mm has been placed longitudinally in a stream of crude oil (specific gravity…

Q: (b) In turbulent flows contrast the approaches that are used to represent the velocity profile…

Question

A 0.5 m x 2 m flat plate is towed at 5 m/s on a 2-mm-thick layer of SAE-30 oil
at 38°C that separates it from a flat surface. The velocity distribution between the
plate and the surface is assumed to be lincar. What force is required if the plate
and surface are horizontal?
1.4

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

Engine oil at 100C flows over and parallel to a flat surface at a velocity of 3 m/s. Calculate the thickness of the hydrodynamic boundary layer at a distance 0.3 m from the leading edge of the surface.
Air at 1000C flows at an inlet velocity of 2 m/s between two parallel flat plates spaced 1 cm apart. Estimate the distance from the entrance to the point where the boundary layers meet.
A 0.5m x 2m flat thin plate is moved at 5m/s on a 2-mm thick layer of SAE 30 oil at 38 degrees Celsius that separates it from a flat surface. The velocity distribution between the plate and the surface is assumed to be linear. What force is required if the plate and surface are horizontal? (μSAE30 = 0.1 N-s/m2)
A 10-cm shaft rides in a 10.03-cm sleeve and 12-cm long, the clearance space (assumed to be uniform) being filled with lubricating oil (? = 0.11 ?? − ?). Calculate the rate at which heat is generated when the shaft turns at 100 rpm in Watts (W). (Rate of energy = Frictional force/resistance x Velocity)
An 16-kg slab slides down a 25° inclined plane on a 4-mmthick film of SAE 30 oil at 15.6 °C; the contact area is0.3m2. Find the terminal velocity of the slab. Explain ur answer
A fluid with a constant density of 961 kg/m3 and a constant viscosity of 1.419×10-3 Kg/m.s is flowing over a flat plate at a stream free velocity of 0.87 m/s. If the plate has a length of 2 m, answer the following: 1.What is Reynolds number at a point that is (1/4)L down the entrance? 2.Is the flow laminar or turbulent? 3.Calculate the thickness of the boundary layer in mm at (1/4)L down the entrance 4.Calculate the drag coefficient at (1/4)L down the entrance
Consider a blimp that can be approximated as a 3-m diameter, 8-m long ellipsoid and is connected to the ground. On a windless day, the rope tension due to the net buoyancy effect is measured to be 120 N. Determine the rope tension when there are 50 km/h winds blowing along the blimp (parallel to the blimp axis).
The thickness of the laminar boundary layer on a flat plate at a point A is 2 cm and at a point B, Im downstream of A, is 3 cm. What is the distance of A from the leading edge of the plate?
Consider the laminar boundary layer flow of an isothermal fluid ( U ∞ , T ∞ ) over a flat isothermal wall ( T 0 ). At a certain distance x from the leading edge, the local skin friction coefficient is C f , x = 0.0066. What is the value of the local Nusselt number at the same location if the Prandtl number is Pr = 7?
Thrust is required to propel an airplane at a fi nite forwardvelocity. Does this imply an energy loss to the system?Explain the concepts of thrust and drag in terms of the fi rstlaw of thermodynamics.
A wind turbine with two or four hollow hemispherical cups connected to a pivot is commonly used to measure wind speed. Consider a wind turbine with four 1-cm-diameter cups with a center-to-center distance of 22 cm, as shown in Fig. 1. The pivot is stuck as a result of some malfunction, and the cups stop rotating. For a wind speed of 20 m/s and air density of 1.25kg/m3, determine the maximum torque this turbine applies on the pivot.
Water at 60° C flows over 2.5 cm square flat plate 90°C at a velocity of 4 m/s. 1- Calculate the drag force , Xcritical 2- If the flat plate is exposed to the natural air convection at 60 °C instead of water with same values of temperatures and length calculate Rayleigh number.