A 1.625-in.-diameter solid steel shaft supports loads PA-390 lb, Pc-570 lb, and PE = 390 lb, as shown. Assume that LAB = 8 in., LBc=20 in., LcD = 10 in., and LDE 14 in. The bearing at B can be idealized as a roller support, and the bearing at D can be idealized as a pin support. Determine the magnitude of the maximum bending stress in the shaft. PA LAB Answer: Omax = i B LBC LCD ksi D LDE E PE

A 1.625-in.-diameter solid steel shaft supports loads PA-390 lb, Pc-570 lb, and PE = 390 lb, as shown. Assume that LAB = 8 in., LBc=20 in., LcD = 10 in., and LDE 14 in. The bearing at B can be idealized as a roller support, and the bearing at D can be idealized as a pin support. Determine the magnitude of the maximum bending stress in the shaft. PA LAB Answer: Omax = i B LBC LCD ksi D LDE E PE

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Thumbs-Up will be given. Write the complette solutions legibly. Answer in 3 decimal places Structural Theory a. Determine the vertical reaction R₂ in KN. b. Determine the shear at midspan between vertical supports in KN c. Determine the maximum factored load moment in the beam in KN.m
If the allowable bearing stress for the material under the supports at A and B (σ_(b allow)= 1.5 MPa, determine the size of square bearing plates A’ and B’ required to support the load. Dimension the plates to the nearest mm. The reaction at the supports are vertical. Take P = 100 kN.
The steel shaft shown rotates at 4 Hz with 35 kW taken off at A, 20 kW removed at B, and 55 kW applied at C. Using G = 83 GPa, find the maximum shearing stress and the angle of rotation of gear A relative to gear C. NOTE: SHOW FREE BODY DIAGRAM AND COMPLETE SOLUTON
The compound shaft is firmly attached to rigid support A. It consists of hollow brass tube AB ( D= 6 in. and d = 2.7 in. ) which is securely connected to solid steel tube BC ( D = 3.8 in. ). Use GBr = 5600 x 103 psi and GSt = 12500 x 103 psi. Determine the shearing stress developed in the brass tube and the total angle of rotation from A to C.
A horizontal beam is supported by an inclined strut and carries a load of 15 kN at joint AD CBD in the figure. The strut, which consists of two bars each of thickness 40 mm, is connected tothe beam by a rivet passing through the three bars meeting at joint. The allowable shear Cstress and bearing stress are all, z =60 MPa and =120 MPa, respectively.a) Determine the required diameter of the rivet at the hinge that carries safely by the given Csystem.b) If the diameter rivet used on the support is 20 mm check whether this rivet diameter is Asufficient for the given system.
The linkage is made of two pin-connected A-36 steel members (E = 29000 ksi), each having a cross-sectional area of 1.5 in 2. If a vertical force of P = 50 kip is applied to joint A, determine the vertical displacement at A.
Compute the force in member BD in kN. P1=117 kN, P2=72 kN and x = 7.8 m. Write numerical value only and in 2 decimal places
A simple pin-connected truss is loaded and supported asshown in Figure P1.12. The load P is 200 kN. All members of thetruss are aluminum pipes that have an outside diameter of 115 mmand a wall thickness of 6 mm. Determine the normal stress in eachtruss member. Assume truss dimensions of a = 12.0 m, b = 7.5 m,and c = 6.0 m.
Determine the axial stress in member BE of the loaded truss if it has a circular cross-section with a diameter of 20 mm.
Thumbs-Up will be given. Write the complette solutions legibly. Answer in 3 decimal places. Please answer all since they are all subquestions. Thanks Structural Theory 1d. Determine the vertical reaction R₂ in kN 1e. Determine the shear at midspan between vertical supports in kN. 1f. Determine the maximum factored load moment in the beam in kN.m
Compute the shearing stress (MPa) in the pin at B for the member supported as shown in the figure below. The pin diameter is 20 mm Final answer should have 2 decimal places Where: L1=200 mm, L2=255mm, P=55 kN and angle =36
Determine the tension at AC. A. 55.23 kN B. 52.53 kN C. 32.55 kN D. 25.35 kN