A 10Vp carrier signal is amplitude modulated by two different frequencies 5 KHz and 10 KHz with amplitude of 4Vp and 7.5Vp respectively using an DSBFC. If the system is connected to the 100Q antenna, (a) what is the modulated carrier power and AM wave total power? From DSBFC, different transmitters with different modulation schemes were used to evaluate the performance in terms of power and bandwidth and compare to conventional AM. (b) Complete the table below and provide your solution. Use 3 decimal places. MODULATED CARRIER AM WAVE TOTAL BANDWIDTH TYPE OF % POWER SAVED POWER (mW) POWER (mW) (kHz) MODULATION SB-FC 500mW (b4) (b5) (b6)

A 10Vp carrier signal is amplitude modulated by two different frequencies 5 KHz and 10 KHz with amplitude of 4Vp and 7.5Vp respectively using an DSBFC. If the system is connected to the 100Q antenna, (a) what is the modulated carrier power and AM wave total power? From DSBFC, different transmitters with different modulation schemes were used to evaluate the performance in terms of power and bandwidth and compare to conventional AM. (b) Complete the table below and provide your solution. Use 3 decimal places. MODULATED CARRIER AM WAVE TOTAL BANDWIDTH TYPE OF % POWER SAVED POWER (mW) POWER (mW) (kHz) MODULATION SB-FC 500mW (b4) (b5) (b6)

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

A 10Vp carrier signal is amplitude modulated by two different frequencies 5 KHz and 10 KHz with amplitude of 4Vp and 7.5Vp respectively using an DSBFC. If the system is connected to the 100Ω antenna, (a) what is the modulated carrier power and AM wave total power? From DSBFC, different transmitters with different modulation schemes were used to evaluate the performance in terms of power and bandwidth and compare to conventional AM. (b) Complete the table below and provide your solution.
If the SNR value is C dB in a communication system, what can be said about the signal strength and noise power in such a system?
Q5) In a superheteridyne receiver, what is the value of the IF frequency?
With the aid of diagrams, show and explain how phase locking is used to: demodulate a frequency-modulated (FM) signal. generate a range of frequencies from a single stable frequency source. synchronise an undersampled signal to the carrier frequency.
What is the maximum average output power of a single-sideband signal (SSB) transmitter rated at 250 W peak envelope power (PEP)? W
For an Armstrong indirect FM transmitter with the crystal carrier oscillating at 210 kHz, the crystal reference oscillating at 10.2 MHz, the sideband voltage is 0.018 V, the carrier input voltage to the combiner is 5V, the first and second multipliers are both 40, and the modulating signal frequency is 2 kHz, determine: a.) modulation index at the output of the combining network and the power amplifier; b.) frequency deviation at the same two points; and c.) the transmit carrier frequency.
Applying Amplitude Modulation Double Sideband Large Carrier (AM DSB-LC) results in a modulated carrier signal bandwidth approximately two times greater than the baseband signal bandwidth (fm). True False
A. How many numbers of constellation points exist in phase for 3bit ASK? B. What happens to the radio wave propagation when the frequency is below critical angle? C. If the mark frequency and space frequency are same then what happens to FSK? D. What is the Carson’s rule? E. What is the Maximum data rate in a minimum channel bandwidth is ? F. What is radio horizon and where is it used? G. What are the phase angle limitations of a BPSK? H. What is the change in channel capacity when two number of bits are increased?
In an AM transmitter and receiver, when a carrier signal has high frequency (2Vpk, and 20kHz)and with the information signal (1Vpk and 1kHz) what happened to the receivers signal? Is it attenuated or not? If it is, does the information signal with low frequency, high voltage and information signal with same value of frequency and voltage affects it? Explain.
A 93.2 MHz carrier is frequency modulated by a 5-KHz sine wave. The resultant FM signal has a frequency deviation of 40 KHz. (a) Find the carrier swing of the FM signal. (b) Determine the highest and lowest frequencies attained by the modulated signal. (c) What is the modulation index of the FM wave (d) Calculate the percent modulation? (e) Determine the bandwidth using approximation method.
Use Carson’s rule to determine the bandwidth of an FM channel when the maximum deviation allowed is 5 kHz at frequencies up to 3.333 kHz. Sketch the spectrum, showing carrier and sideband values.
What is the bandwidth of a narrowband FM signal generated by a 2 kHz audio signal and 110 MHz FM carrier?