A 116 Ω resistor and an unknown capacitor are connectedin series to an ac source with angular frequency 5.10 * 10^3 rad/s. Theamplitude of the resistor voltage is 2.45 V, and the current in the circuithas its maximum positive value at t = 0. Find the capacitance

A 116 Ω resistor and an unknown capacitor are connectedin series to an ac source with angular frequency 5.10 * 10^3 rad/s. Theamplitude of the resistor voltage is 2.45 V, and the current in the circuithas its maximum positive value at t = 0. Find the capacitance

Delmar's Standard Textbook Of Electricity

7th Edition

ISBN:9781337900348

Author:Stephen L. Herman

Publisher:Stephen L. Herman

Chapter17: Resistive-inductive Series Circuits

Section: Chapter Questions

Problem 2PP: Assume that the voltage drop across the resistor, ER, is 78 V, that the voltage drop across the...

See similar textbooks

Related questions

Q: Next the multimeter will be used to measure the voltage VOUT_B for the second potential divider. The…

A: We need to find out output voltage for given circuit.

Q: 2. For a 0.5μm process technology, for which tox= 15 nm & n = 550 cm²/s- Find Cox, Kn and over drive…

A: Solution !!

Q: SW1 SW2- L1 A 1₁ B 2 LEDS L2 D 1 3 4 5 2 C L3 What logic function is being performed? LED

Q: A series R-C circuit consists of a resistor of 700 2, time constant of 28 msec. The value of…

A: The time constant is the time taken by the RC network to reach 63.2% of its final value.

Q: The circuit shown below on the left has the following parameters: Vs = 11 V Is=7A R₁ = 1.20 R₂=2.20…

Q: According to Carson's rule, Bandwidth B and modulating frequency fm are related a a. B = 2(Af + fm)…

A: According to Carson's rule,

Q: C. Problem Solving. Draw the circuit and show your complete solutions. 1. Given the value of a 6-ohm…

Q: The values in the schematic are: VIN = 3.5 V, R1 = R2 = 6.6 k0, R3 = R4 = 660 kn, and R5 = R6 = 6.6…

A: We need to find out output voltage for given circuit

Q: QUESTION 12 For the following two phasors: V=202-48 I= 102-19° What is the phase angle in degree by…

A: Given data, The two phasors are V=20∠-48°I=10∠-19°

Q: To achieve 75 percent modulation of a carrier of V, 190 V, what amplitude of the modulating signal V…

A: Modulation index is given, m=75 %=0.75 Amplitude of carrier signal Vc=190 V

Q: 4. A three-phase unbalanced supply system having phase voltages, Va=1.140° pu., Vb-1.0230° pu.,…

A: Since you have posted a question with multiple sub-parts, we will solve the first three subparts for…

Q: 4. Find the total impedance in polar form for the following three parallel impedances: 12/10,25/15…

A: Given three parallel impedances are 12∠10o, 25∠15o, 34∠26o Find the total impedance.

Q: The voltage across a 81 mF capacitor is 15.4 V. How much energy is stored in the capacitor in W?…

A: Given, C= 81 mF V= 15.4 V W=?

Q: 18. A current of 16 amperes divides between two branches in parallel of resistances 8 ohms and 12…

A: We need to find out current for given circuit

Q: Determine the divergence of the vector field P = x²yz ax + xy az O a. 2xyz ax O b. 2xyz O c. 2xyz +…

A: We need to find out divergence of given vector .

Q: Two resistors R1=1000 Ohm and R2= 500 Ohm are connected in parallel. The total current is 10 A. The…

Q: 2. (a) Determine the current in the circuit below. Hint view video on multip (b) Determine the…

A: Given circuit,

Q: The voltage across 20 Resistor where v= 10volts is 20 W O a. 4V O b. 10V О с. 3V O d. 2V in W m 20 V

Q: 1. For the network of Fig., determine: (a) S(co) {b) S(Var) (c) S(B) Using T, as the temperature at…

A: Solution !!

Q: A. Find the value of the total current (I) and real power (P) in the given circuits below. 1. All…

A: We need to find out current and power for given circuit

Q: In your own words, explain why the circuit in Figure 3.2 is regarded as a logical inverter. Comment…

Q: 1. Write 10+j 20 in polar coordinates 2. Sein rectangular coordinates 3. 15-j 30 in polar…

A: Given data, 1. Function is given 10+j20 Converting it in polar form, 102+202∠tan-12010=22.36∠63.430

Q: A moving coil instrument requires 20mA and 100mV for full-scale deflection. What is the value of the…

A: Given data, Full scale deflection current Im=20 mA Full scale deflection voltage Vm=100 mV Current…

Q: needed in order to successfully capture frequencies up to 80MHz in an analog

Q: Calculate Vo and lo in the circuit. Vo = Blank 1 V lo = Blank 2 mA 200 V (+ Blank 1 Blank 2 70 92 20…

A: We need to find out the voltage and current for given circuit

Q: Use Superposition theorem to calculate current through R, resistor. R₁ E 48 V 10 A 10 A R₂ 200 R₂ 50

A: Given data, Circuit diagram is given as,

Q: A 6-pole motor turns at 1080 rpm when connected to a 60 Hz voltage source. Most nearly, what is the…

A: Step-1--> We have motor speed(Ne)=1080 rpm f=60Hz We know , synchronous…

Q: RMS value of an alternating current is 30 A and its frequency is 25 Hz. Write its equation to find…

A: We have an RMS value of an alternating current and we have been asked to find its instantaneous…

Q: A generating station distributes the following loads. 2500KW, 7500KW, 15000KW and 3500KW, The…

Q: A six-pole induction motor operating in the United States has a rated slip of 3%. What is its rated…

A: Given, An induction motor operating in United states has Number of poles, P=6 Rated slip, s=3%=0.03…

Q: Find the transfer function from e; (t) to e(t). O CLs+1 CLS2+RCs+1 CLs+R CLS2+RCs+1 CLs² +1…

A: Given circuit,

Q: 1) Find the Req for the circuit shown in below figure.

A: Given circuit can be represented as-

Q: Vs VA R₁ 1₁ R3 Vc VB R₂ 2 = 100 (2, R3 = 50 (2, R4 = 90 02, and Vs = 10 V. 01 Substitute the values…

A: This question belongs to circuit theory . It is based on the concept of mesh analysis in the circuit…

Q: When a second-order system is subjected to a unit step input, the values of = 0.5 and wn = 6…

Q: Exercise Determine the transfer function of the network below: vi(1) + 192 192 1 H oooo 2 F + Vo(t)

Q: The SCR based half-wave rectifier with a resistive load is shown in Figure 1 (left). The voltage…

A: The SCR based half-wave rectifier with a resistive load is shown below, The applied signals…

Q: What is the power factor

Q: The contribution of current source /2 is now calculated by making /₁ open circuit. R₁ = 3.8 Q, R2 =…

Q: 3. A load of 40+j55 ohm is connected across a 120-Volt source. Determine the value of the reactive…

A: Given parameters: Load resistance, RL = 40 + j55 ohm Source voltage, Vs = 120 V To find: Reactive…

Q: In the figure shown below, determine the power of the voltage source. 352 6A (↑) 252 ww wit 201

A: Given circuit,

Q: Give an example of a material’s electrical property.

A: The Electrical conductivity of the material is the electrical property of the material. The…

Q: A coil takes 2.5 A, when connected across 200V, 50 Hz main. The power consumed by the coil is found…

A: We need to find out resistance and inductance for given coil

Q: A three-phase induction motor with 72 stator windings is excited with a 50 Hz AC voltage source. The…

A: Given: A 3-phase induction motor has 72 stator windings. Excitation frequency, f=50 Hz Slip,…

Q: The voltage across a 2.3 kW electric stove is 220 V; what is the current passing the stove in A? O…

A: Given: An electric stove has V=220 VP=2.3 kW

Q: A single phase line has a resistance of 52ohm per conductor and an inductance of 25 mH per…

Q: For step response of an under damped second order system, the settling times are given as: ts1: for…

A: Given for step response of a under damped system Settling time for 1% tolerance band: ts1 Settling…

Q: Simplify the following Boolean expressionsF = (A+ B)'(C + D+ E)'+ (A+ B)'

A: Given- F = (A+ B)'(C + D+ E)'+ (A+ B)' To find- Simplified version = ?

Q: For the waveform of current i shown in Figure 1.2, compute the total charge q transferred between…

A: This question belongs to circuit theory . It is based on the concept of calculation of charge…

Q: If an 8-bit binary number is used to represent an analog value in the range from 010 to 10010, What…

A: Given 010101102 is the given binary number.

Q: 11a) Give 5 different examples of field devices can provide digital input signals to a PLC. b)…

A: a). An input device is a piece of computer hardware equipment used to provide data, and control…

Question

A 116 Ω resistor and an unknown capacitor are connected
in series to an ac source with angular frequency 5.10 * 10^3 rad/s. The
amplitude of the resistor voltage is 2.45 V, and the current in the circuit
has its maximum positive value at t = 0. Find the capacitance

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 2 steps with 1 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Sinusoids and Phasors of Alternating Circuit

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, electrical-engineering and related others by exploring similar questions and additional content below.

Similar questions

A series RLC circuit consists of 20 ohms resistance, 0.2 H inductance and an unknown capacitance. What is the value of the capacitance if the circuit has a leading angle of 45° at 60 Hz? a. 35.18 μF b. 47.9 μF c. 27.8 μF d. 30.7 μF
For a series inductance and capacitance with value of L=2H and C=0.25 F. Solve for X(s) when Vo is at the inductance.
A 160 μF capacitor is connected in series with a 10 Ω resistor. Write the equation of the current when the voltage is 220 Vp? a. 11.4 sin (377t + 59) b. 8.9 sin (377t – 46) c. 9.8 sin (377t + 52) d. 7.2 sin (377t + 46)
A given RLC circuit (Resistor-Inductor-Capacitor) has the following components: R = 4.1 Ohms L = 0.0099 H C = 0.00011 F If this system is driven by an oscillating current with frequency f = 2,594 Hz, what is the Inductive Reactance (XL) of this system?
A 200 Ω resistor, 0.900 H inductor, and 6.00 µF capacitor are connected in series across a voltage source that has voltage amplitude 30.0 V and an angular frequency of 250 rad/s. (a) What are v, vR, vL, and vC at t = 20.0 ms? Compare vR + vL + vC to v at this instant. (b) What are VR, VL, and VC? Compare V to VR + VL + VC. Explain why these two quantities are not equal.
S:41) A circuit consists of a current source, Is = 43 sin(5386t - 40.29 °) mA in parallel with a 72 kΩ resistor and a 2895 pF capacitor. Determine the magnitude of the effective value of current that flows through the resistor.
A LC circuit in a radio tuned to 1080 kHz has an inductor with an inductance value of 60 μH and a resistance of 0.25 Ω. a. what is the capacitance of the LC circuit? b. sketch the impedance phasor diagram for the radio. Be sure to label important features of the diagram.
The current in an L-R-C series circuit has amplitude 0.120 Aand angular frequency 8.00 * 103 rad/s, and it has its maximum positivevalue at t = 0. The resistance is 95.0 Ω, the inductance is 6.50 mH,and the capacitance is 0.440 mF. For the resistor, inductor, and capacitor,find (a) the voltage amplitudes and (b) the instantaneous voltages att = 0.305 ms.
Capacitance= 10uF , t≈65 μs, Vfinal=4VPlot capacitor current and voltage graphs. NOTE: if you want you can use falstad online circuit simulator.
An L-R-C series circuit has R = 60.0 Ω, L = 0.800 H, and C = 3.00 x 10-4 F. The ac source has voltage amplitude 90.0 V and angular frequency 120 rad/s. (a) What is the maximum energy stored in the inductor? (b) When the energy stored in the inductor is a maximum, how much energy is stored in the capacitor? (c) What is the maximum energy stored in the capacitor?
Determine the equivalent capacitance, Cab , Lab , and Rab , as seen at terminals a-b.
An AC Voltage Generator provides 100 V at angular frequency of 500 rad/s to a series RLC, R = 3 ohms, C = 50 uF, L = 10 to 80 mH. Peak Voltage across the capacitor should not exceed 1200 V. A. Determine the voltage across the Inductor, VL(t). Hint: VL(t) leads VR(t) by 90 degrees. What is the average voltage across the inductor, VL? B. Determine the voltage across the Capacitor, VC(t). Hint: VC(t) lags VR(t) by 90 degrees. What is the average voltage across the capacitor, VC? C. Show that V ≠ VR + VL + VC