A 120 N weight is attached to the cable that is wrapped around the 50-N homogeneous drum. The shaft attached to the drum is supported by a thrust bearing at A and a slider bearing at B. The drum is kept in equilibrium by the vertical force P acting on the handle of the crack. If P is 70 N, determine the diameter of drum, and the reactions at A and B. Neglect the weight of the crack and the shaft. 12 - 32- 28 A, 15 24 В 50N 12 -/ 120 N Dim in inches

A 120 N weight is attached to the cable that is wrapped around the 50-N homogeneous drum. The shaft attached to the drum is supported by a thrust bearing at A and a slider bearing at B. The drum is kept in equilibrium by the vertical force P acting on the handle of the crack. If P is 70 N, determine the diameter of drum, and the reactions at A and B. Neglect the weight of the crack and the shaft. 12 - 32- 28 A, 15 24 В 50N 12 -/ 120 N Dim in inches

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

a vertical force of 60 KN acts on the cage system in the figure from point D. If the perpendicular cross-sectional area of the BC bar is 1000 mm2 and the perpendicular cross-sectional area of the other bars is 500 mm2, then E = 200 GPAa) find the total deformation energy of the cage systemb) find the vertical displacement of Point Dc) find the horizontal displacement of Point C.
5.2.2 The thin-walled tube is used as a beam to support the uniformly distributed load of intensity w0. (a) Find the largest allowable value of w0 based on the allowable stress in bending of 100 MPa. (b) Compute the corresponding maximum shear stress in the beam.
Compute the deformation in member 1 which is solid alumnim with a area of 214159 mm^2
What is the reaction at support C for the beam shown and a settlement of 25 mm at supportC
portal method determine the magnitude reaction at a
The copper pipe has an outer diameter of 40 mm and an inner diameter of 37 mm. If it is tightly secured to the wall at A and three torques are applied to it as shown, determine the maximum shear stress developed in the pipe. Let T1=66, T2 =11, T3 =26
If the output torque on the CD shaft is T ́ = 75 N-m and the motor rotates at 175 rpm, determine the power delivered by the motor in watts. • Is there torque at the BE and CF ends? • Calculate the maximum shear stress in the AE axis.
assume phi=0 throughout and tension crack filled with water, find FOS. the tension crack is assumed to extend completely the top layer.
12- Permanent deformation takes place after Yield point Select one: True False
The beam is built in at both ends and loaded by a distributed load which has the constant intensity w at the first two thirds of the beam length and linearly decreases from w to zero over the remaining part of the beam length (Fig. 1). Find the equation for the w value at the onset of the plastic collapse in terms of the beam cross-section fully plastic moment, Mp, and I.
The cantilever beam is subjected to a concentrated load of P=20kips. The cross-sectional dimensions of the rectangular tube shapre are b=5.2in , d=8.10in , and t=0.400in. Determine:a) The magnitude of the maximum horizontal shear stress in the rectangular tube shape. Answer in ksi, rounded-off to 2 decimal places.b) The magnitude of the shear stress at point K, which is loacted to the left of the vertical centroidal axis zK=1.1in. Answer in ksi, rounded off to 2 decimal places.
Determine the total stress σv 0 acting on the review level