A 13-kN hydraulic press for removing and reinstalling bearings in small-to medium-sized electric motors is to consist of a commercially available cylinder mounted vertically in a C- frame, with dimensions as sketched in the Figure shown below. It is being proposed to use ASTM A-48 (Class 50) gray cast iron (brittle material with ultimate strength, s.,= 345 MPa) for the C-frame material. State whether true/false. Under the loading conditions, failure happens 18 mm 38 mm 13 kN 25 mm 10 mm -90 mm At A 10 mm

A 13-kN hydraulic press for removing and reinstalling bearings in small-to medium-sized electric motors is to consist of a commercially available cylinder mounted vertically in a C- frame, with dimensions as sketched in the Figure shown below. It is being proposed to use ASTM A-48 (Class 50) gray cast iron (brittle material with ultimate strength, s.,= 345 MPa) for the C-frame material. State whether true/false. Under the loading conditions, failure happens 18 mm 38 mm 13 kN 25 mm 10 mm -90 mm At A 10 mm

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter2: Axially Loaded Members

Section: Chapter Questions

Problem 2.5.1P: The rails of a railroad track are welded together at their ends (to form continuous rails and thus...

See similar textbooks

Similar questions

A high-strength steel bar used in a large crane has a diameter d = 2.00 in. (sec figure). The steel has a modulus of elasticity E = 29 × 10 psi and Poisson’s ratio is v = 0.29. Because of clearance requirements, the diameter of the bar is limited to 2.001 in. when it is compressed by axial forces. What is the largest compressive load Pmaxthat is permitted?
A 25 mm diameter cylindrical rod fabricated from 2014-T6 Al alloy is subjected to repeated tension-compression load cycling. The data is plotted for σm = 20 MPa. In order to have fatigue life of 1.0x107 cycles, calculate Stress Ratio and mention whether it is a case of HCF or LCF.
Two steels are being considered for manufacture of as-forged connecting rods subjected to bending loads. One is AISI 4340 Cr-Mo-Ni steel capable of being heat-treated to a tensile strength of 260 ksi. The other is a plain carbon steel AISI 1040 with a ultimate strength of 113 ksi. Each rod is to have a size giving an equivalent diameter of 0.75 in. Determine the endurance limit for each material. Is there any advantage to using the alloy steel for this fatigue application?
A component is subjected to a maximum cyclic stress of 750 MPa and a minimum of 70 MPa. The steelfrom which it is manufactured has an ultimate tensile strength, σu, of 1050 MPa and a measured endurancelimit, σe, of 400 MPa. The fully reversed stress at 1000 cycles is 750 MPa. Using both the Goodman and Gerbermean stress correction procedures, calculate the component life.
Example 4 A bar of circular cross - section is subjected to alternating tensile forces varying from a minimum of 200 kN to a maximum of 500 kN. It is to be manufactured of a material with an ultimate tensile strength of 900 MPa and an endurance limit of 700 MPa. Determine the diameter of bar using safety factors of 3.5 related to ultimate tensile strength and 4 related to endurance limit and a stress concentration factor of 1.65 for fatigue load. Use Goodman straight line as basis for design.
A bar of circular cross-section is subjected to alternating tensile forces varying from a minimum of 200 kN to a maximum of 500 kN. It is to be manufactured of a material with an ultimate tensile strength of 900 MPa and an endurance limit of 700 MPa. Determine the diameter of bar using safety factors of 3.5 related to ultimate tensile strength and 4 related to endurance limit and a stress concentration factor of 1.65 for fatigue load. Use Goodman straight line as basis for design.” [1]
Produced from xCy steel material by machining method, the shaft is bedded at C and D points. With the shaft, constant Fy= 870 N forces in the vertical direction and constant Fx= 4,7 kN forces in the axial direction, which do not rotate together. The tensile strength of the shaft material is (sigma)tensile = 670 MPa and the yield strength is (sigma)yield = 470 MPa. For 50% reliability, analyze the fatigue damage condition of the shaft sections A and B separately. Note: Take SI unit and make the solutions legit and clear please
A massless bar has a rectangular cross-section as shown in the figure. The rod is made of Cast Iron Gray ASTM 20. Under the loading conditions as shown in the picture with a factor of safety of n = 3, will point A crack?
A cylinderbar of steel,10 mm in diamter is to be defromed elastically by application of a force along the bar axis (axial loading) .determine the force that will produce an elastic reduction of 0.003 mm in the diameter.The poisson's ratio is 0.30 and the modulus of elasticity is 207 Gpa for carbon steel.
A tensile-testing apparatus is to be constructed that must withstand a maximum load of 293516 N. The design calls for two cylindrical support posts, each of which is to support half of the maximum load. Furthermore, plain-carbon(1045) steel ground and polished shafting rounds are to be used; the minimum yield and tensile strengths of this alloy are 343 MPa and 565 MPa(82,000 psi), respectively. Specify a suitable diameter in mm for these support posts. Assume safety level is 2.3. Round your answer to 2 significant figures.
A 759-lb force is applied to a rotating tool steel bar at a frequency of 3000 cycles/minute. The bar has a diameter of 1.000 in. and is 12.00 in. long. The fatigue curve for the steel used in the bar is shown below. Calculate the time in minutes to failure given ±σ=32FLπd3.
a) Determine the minimum required thickness "t" for the element shown in the figure, if it will be manufactured in AISI 1060 HR steel, which works at an operating temperature of 265 ° C, with a reliability of 90%. The applied load is alternating and a safety factor of 1.7 is desired. I explained the reason for your answer.b) What is the critical point and why?