A 15" x 3/8" bar of A572 Gr. 50 steel is used as a tension member. It is connected to a gusset plate with 7/8-in diameter bolts as shown in the figure. Use s = 2.0 and g = 3.0. Determine the allowable tensile strength of the section based on tensile rupture of the net area.

A 15" x 3/8" bar of A572 Gr. 50 steel is used as a tension member. It is connected to a gusset plate with 7/8-in diameter bolts as shown in the figure. Use s = 2.0 and g = 3.0. Determine the allowable tensile strength of the section based on tensile rupture of the net area.

Steel Design (Activate Learning with these NEW titles from Engineering!)

6th Edition

ISBN:9781337094740

Author:Segui, William T.

Publisher:Segui, William T.

Chapter5: Beams

Section: Chapter Questions

Problem 5.12.2P

See similar textbooks

Related questions

Q: The hot air balloon exerts a 1000 N force along the y-axis. If the allowable tensile stress on the c...

Q: How much should the engineer borrow from a bank that charges 10% simple discount for 6 months if he ...

Q: An oil of viscosity 5 poise is used for lubrication between a shaft and sleeve. The diameter of the ...

Q: Problem 2: Fluid flows through a 20-mm diameter pipe, 150 m long at a Reynolds number of 1,750. Calc...

Q: A double-angle shape is shown in the figure. The steel is A36, and the holes are for 1/2-inch-diamet...

A: To determine the allowable tensile strength for ASD. Given, Grade of steel: Fy = 36 ksi and Fu = 5...

Q: The tractor-trailer unit is moving down the incline with a speed of 6.0 mi/hr when the driver brakes...

A: Estimate the percent increase n in the hitch-force component which is parallel to the incline, compa...

Q: Over a hydraulic drop structure in a river 22.8 m wide flows 170 m3/s. On the level apron of the str...

Q: In using the rational formula, Q ▪ CIA, for the design of any structure, what do the terms Q. C, I, ...

A: Q = CIA Q = Peak rate of runoff ( in cubic feet per second ) i = Rainfall Intensity (inch/hour) A...

Q: A homogeneous sphere S, a uniform cylinder C, and a thin pipe P are in contact when they are release...

Q: 2. The lost ABCDEFGH is a closed traverse (clockwise) in the form of a regular octagon. If the beari...

A: according to bartleby policy I can answer first 4 questions only. please re-upload the remaining one...

Q: Q3. Re-right the above equation for the following conditions a. dry cohesion soil (7 sar – my „) tan...

A: Answer: Given equation Fs=cγsatHcosβsinβ+(γsat-mγw)tanϕγsattanβ

Q: Determine the collapse load for a square two-way slab with equal horizonta' and vertical reinforceme...

Q: Determine the maximum discharge obtaina that carries water from a mountain reservoir to a hydroelect...

A: Given, Diameter (d) = 0.4 m Length (L) = 2500 m

Q: Situation 03. Joe wants to test how fast can SuperMan save him if he jumps of a cliff 180m high. He ...

Q: Check stability of truss

A: Given data : The number of Joint in a truss J=3 The number of member in a truss m=2 Support conditio...

Q: Find the collapse load in a 7m x 5m rectangular slab fixed at all edges for which the support moment...

Q: 18.2 kN/m 36.4kN/m

Q: Compute the maximum deflection for the beam loaded as shown below 400 Ib 400 Ib 160 Ib/ft 100 Ib/ft ...

A: To find Maximum deflection for the beam

Q: The following represents infiltration data; Calculate the following 1. Infiltration rate for all dat...

A: "Since you have asked multiple sub-parts. We will solve the first two sub-parts for you. To get the ...

Q: The small body has a speed vA = 6.5 m/s at point A. Neglecting friction, determine its speed at poin...

Q: A beam will be lifted from the ground by means of a bridge crane, during the construction of the las...

A: In multi-story structures where the loads on the columns are extremely high, composite segments made...

Q: Q2: For the cantilever retaining wall shown below, calculate the factor of safety with respect to ov...

A: Calculate the factor of safety against overturning by the using following formula, F.O.S=MOMR ...

Q: B. A simple curve has a radius of 272.6m. Its distance from PC to PT along the curve is 256m. 4) Com...

Q: If IG is the mass moment of inertia of a rigid body with respect to an axis passing through its cent...

Q: Two forces, each of magnitude P, are applied to the wrench. The diameter of the steel shaft AB is 15...

Q: 3. A circular steel bar with cross sectional area of 4 in is loaded as shown. a) Compute the shear a...

Q: 2. Determine the normal stress in members DF, GH, and GI in the truss shown. The cross- sectional ar...

Q: A column 3 m long and pinned at both ends is carries an axial load of 190 kN. The column is made up ...

Q: A turbine is rated at 700 hp when the flow of water through it is 0.72 m3/s. Assuming the efficiency...

A: Answer: We are given Power (P) =700 hp Flow rate(Q) = 0.72 m3/s Overall Efficiency(ηo) = 78%

Q: A simple curve having a radius of 229.18 m has a back tangent of N 28° E, and a forward tangent of N...

A: The given values are shown below,Radius =229.18Back tangent=N28°EForward tangent=N66°EDistance=10mCu...

Q: What will be the critical depth for flow at 0.4 m3/s through the cross-section shown below (in m) 60...

A: Given : Discharge through triangular channel, Q...

Q: A sample of saturated clay from a consolidometer test has a total weight of 1.526 kg and a dry weigh...

Q: #3) A sand soll sample is subjected to a direct shear test under a normal load of 185 kPa. The speci...

A: This question is related to the Geotechnical Engineering.

Q: 2. Calculate the total stopping sight distance for a wet pavement condition, if the design speed is ...

Q: 5mm 13mm mm Select one: a. 9.95 b. 10.11 c. 7.52 d. 8.73 3mm 6mm

Q: Explain the axis translation technique without using any figure. What are the limitations of this t...

A: The axis translation technique is a grounded technique for forcing upsides of pull unsaturated soil...

Q: Situation 03. Joe wants to test how fast can SuperMan save him if he jumps of a cliff 180m high. He ...

Q: What is capillarity in parallel plates? What are the uses of it and how does it work?

A: When the distance between the plates is very small and plates are immersed in liquid, the liquid may...

Q: # 3) A sand soll sample is subjected to a direct shear test under a normal load of 185 kPa. The spec...

A: Given Data : in the above question we have given;shere stress (S);ie; S=100KPanormal load(σn1);ie; σ...

Q: A clay soil has a void ratio of 0.53 at its liquid limit. The absolute specific gravity is 2.65 and ...

Q: PROBLEM #1 4 kN/m A 6 m B 10 kN

Q: Design the shear Reinforcements of the following beam using only two stirrup spacings and draw the d...

Q: Q4: For the composite structures shown in Fig.(4), draw influence lines for 1- moment at A, member C...

Q: Aluminum A = 400 mm? Bronze A = 200 mm? Steel A = 500 mm? 2P 4P 2.5 m 2.0 m 1.5 m P.

Q: What is the amount of usage in hours per year if initial cost of bulldozer is Php 25.5 M with operat...

Q: Each of the sliders A and B has a mass of 1.8 kg and moves with negligible friction in its respectiv...

A: To find speed v which A strikes

Q: re change of the assembly that will cause a tensile stress of 50 MPa in the steel rod. Use lata: A (...

Q: How should they be resolved? a. Improper Electrical Wiring b. Plumbing Problems c. Minor Structural ...

A: To fix the problem, turn off the power to the device, then disconnect the wires and either clip off ...

Q: A vessel, cylindrical in shape and closed at top and bottom, contains water upto a height of 80 cm. ...

Q: The diameter of a pipe carrying water changes gradually from 15 cm at section A to 45 cm at section ...

A: We will apply bernoulli at A and B

Question

A 15" x 3/8" bar of A572 Gr. 50 steel is used as a tension member. It is connected to a gusset plate with 7/8-in diameter bolts as shown in the figure. Use s = 2.0 and g = 3.0.

Determine the allowable tensile strength of the section based on tensile rupture of the net area.

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1: Introduction

VIEW

Step 2: Allowable tensile strength of the section

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 2 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

A 15" x 3/8" bar of A572 Gr. 50 steel is used as a tension member. It is connected to a gusset plate with 7/8-in diameter bolts as shown in the figure. Use s = 2.0 and g = 3.0. a) Determine the allowable tensile strength of the section based on tensile rupture of the net area.b) Determine the allowable tensile strength of the section based on yielding of the gross area.
Determine the smallest diameter (mm) that can be used in the clevis shown in the figure below if P = 421 kN. The shearing stress of the bolt is 305 MPa. Final answer should have 2 decimal places.
A 15" x 3/8" bar of A572 Gr. 50 steel is used as a tension member. It is connected to a gusset plate with 7/8-in diameter bolts as shown in the figure. Use s = 2.0 and g = 3.0. Determine the design tensile strength of the section based on tensile rupture of the net area. Determine the allowable tensile strength of the section based on yielding of the gross area.
Determine the nominal tensile strength of the single angle. Consider 7/8" diameter bolt and A242 steel with Fy = 50 ksi and Fu = 70 ksi. L6x6x3/4 d = 6 in. b = 6 in. t = 0.75 in. k = 1.25 in. wt./ft. = 28.8 plf. A = 8.46 in.^2 x = 1.77 in.
A hollow steel [E = 30,000 ksi] tube (1) with an outside diameter of 3.00 in. and a wall thickness of 0.223 in. is fastened to a solid 1.75-in.-diameter aluminum [E = 10,000 ksi] rod. The assembly is attached to unyielding supports at the left and right ends and is loaded as shown. Assume P=18 kips, Q=13 kips, L1=4 ft, L2=6 ft, and L3=6 ft. Determine(a) the stresses in all parts of the axial structure.(b) the deflections of joints B and C.
Compute for the linear weight of a 32mm diameter reinforcing bar. (Use the Unit weight of the Steel) Answer asap
The figure as shown below is a rigid bar (ABCD) which was supported thru pin at B. Two bars was also connected, Bar CE and Bar DF with corresponding cross-sectional area and Modulus of Elasticity. If P is equivalent to 94 kN, the diameter at pin B is Blank 1 mm. with drawing and complete solution
Given the truss shown, solve the following. Use A36 steel and assume there are two lines of three 19 mm bolts in each flange. Hole diameter is assumed to be three mm more than the bolt diameter. Neglect the weight of the section. a.What is the capacity of member CG? b. Design member CG using a W section. c. What is the tensile capacity of the section for CG based on gross area?
TENSION MEMBERS: THE SINGLE 200 X 10 mm STEEL PLATE IS CONNECTED TO A 12 mm THICK STEEL PLATE BY FOUR 16 mm DIAMETER RIVETS AS SHOWN IN THE FIGURE. THE RIVETS USED ARE A502 GRADE 2, HOT DRIVEN RIVETS. THE STEEL IS ASTM A36 WITH Fy = 248 MPa AND Fu = 400 MPa. DETERMINE THE VALUE OF P. a. P BASED ON TENSION OF GROSS AREA b. P BASED ON TENSION OF NET AREA c. P BASED ON BEARING OF PROJECTED AREA d. P BASED ON SHEAR RUPTURE (BLOCK SHEAR)
13.A rectangular beam has b = 300 mm and d = 410 mm. The beam is used to carry a factored moment of 20 kN-m. Assume f'c = 28 MPa and fy = 280 MPa. Calculate the required steel area in mm2. Express your answer in nearest whole number
The dimensions of a rectangular beam are limited to b = 300 mm and h = 770 mm. Assume that the bar centroid of tension bars is 70 mm from the beam edge and that of compression bars is 60 mm. Using f’c = 28 MPa, long bar fy = 415 MPa, calculate the following for a factored bending moment of 1200 kN: a. Maximum steel ratio limiting the tensile strain to 0.004. b. Required amount of tensile reinforcement if the tensile steel strain is limited to 0.005. c. Required amount of compression reinforcement.
Two forces, each of magnitude P, are applied to the wrench. The diameter of the steel shaft AB is 16.6 mm. Determine the largest allowable value of P (in N) if the shear stress in the shaft is not to exceed 89.31 MPa and its angle of twist is limited to 5.38˚. Use G = 80.35 GPa for steel and L = 455 mm. Round off the final answer to two decimal places.