A 150 min x a mnm x 20 mm stecl plate is subjected a pull of 150 kN along its central axis as show in figure. A hole of 40 mm diameter is drilled in the plate whose center is 50 mm alway from central longitudinal axis. Calculate the max stress in the plate, 40 min 40 nun 75 mm 50 mm 150 kN I50 km 75 nam

A 150 min x a mnm x 20 mm stecl plate is subjected a pull of 150 kN along its central axis as show in figure. A hole of 40 mm diameter is drilled in the plate whose center is 50 mm alway from central longitudinal axis. Calculate the max stress in the plate, 40 min 40 nun 75 mm 50 mm 150 kN I50 km 75 nam

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter8: Applications Of Plane Stress (pressure Vessels, Beams, And Combined Loadings)

Section: Chapter Questions

Problem 8.5.6P: A cylindrical tank subjected to internal pressure/? is simultaneously compressed by an axial force F...

See similar textbooks

Similar questions

A cylindrical tank subjected to internal pressure/? is simultaneously compressed by an axial force F = 72 kN (see figure). The cylinder has diameter d = 100 mm and wall thickness t = 4 mm. Calculate the maximum allowable internal pressure /?max based upon an allowable shear stress in the wall of the tank of 60 MPa.
A prismatic bar with a length L = 3 ft and cross-sectional area A = 8 in2 is compressed by an axial centroidal load P = 10 kips. Determine the complete state of stress acting on an inclined section pq that is cut through the bar at an angle W = 35", and show the stresses on a properly oriented stress element.
Solve the preceding problem for a W 200 × 41,7 shape with h = 166 mm, h = 205 mm. rw = 7.24 mm, tE= ILS mm,andV = 38 kN.
A single steel strut AB with a diameter (a) Find the strut force Fs and average normal stress ds= 8 mm supports the vehicle engine hood of a in the strut. mass 20 kg that pivots about hinges at C and D (see (b) Find the average shear stress t aver in the bolt at A,figure parts a and b). The strut is bent into a loop at (C) Find the average bearing stress bon the bolt at A. its end and then attached to a bolt at A with a diameter db= 10 mm. Strut AB lies in a vertical plane.
A circular pole is subjected to linearly varying distributed force with maximum intensity t0. Calculate the diameter daof the pole if the maximum allowable shear stress for the pole is 75 M Pa.
Solve the preceding problem if F =90 mm, F = 42 kN, and t = 40°MPa
An aluminum pole for a street light weighs 4600 N and supports an arm that weighs 660 N (see figure). The center of gravity of the arm is 1.2 m from the axis of the pole, A wind force of 300 N also acts in the (y) direction at 9 m above the base. The outside diameter of the pole (at its base) is 225 mm, and its thickness is 18 mm. Determine the maximum tensile and compressive stresses o, and e1., respectively, in the pole (at its base) due to the weights and the wind force.
A circle of a diameter d = 200 mm is etched on a brass plate (see figure). The plate has dimensions of 400 x 400 x 20 mm. Forces are applied to the plate, producing uniformly distributed normal stressescr^ =59 MPaander^ = —17 MPa. Calculate the following quantities: (a) the change in length Aac of diameter at: (b) the change in length Abd of diameter bd; (c) the change At in the thickness of the plate; (d) the change AV in the volume of the plate; (e) the strain energy U stored in the plate; (f) the maximum permissible thickness of the plate when strain energy £/must be at least 784 J; and (g) the maximum permissible value of normal stress axwhen the change in volume of the plate cannot exceed 0.015% of the original volume. (Assume E = 100 GPa and v = 0.34
A fire extinguisher tank is designed for an internal pressure of 825 psi. The tank has an outer diameter of 4.5 in. and thickness of O.OS in. Calculate the longitudinal stress, the circumferential stress, and the maximum shear stresses (out-of-plane and in-plane) at the outer surface of the tank.
A vertical pole consisting of a circular tube of outer diameter 5 in. and inner diameter 4.5 in. is loaded by a linearly varying distributed force with maximum intensity of q0, Find the maximum shear stress in the pole.
A gondola on a ski lift is supported by two bent arms, as shown in the figure. Each arm is offset by the distance b = ISO mm from the line of action of the weight force W. The allowable stresses in the arms are 100 MPa in tension and 50 MPa in shear. If the loaded gondola weighs 12 kN, what is the minimum diameter roof the arms?
‘7.3-11 The stresses on an element are sx= -300 psi and sy= 600 psi. Find the maximum shear stresses on the element and show them on a sketch of a properly oriented clement.