A 20 °C water flows to 50cmx60cm flat plate with velocity of 6m/s . The flat plate surface temperature is maintained at 40 °C The water flows parallel to the 50cm side of the plate. If the kinematic viscosity of water is 78x10-8 m2/s, What is the local heat flux (Q/A) at the end of the plate (k=0.86 W/m deg C, Re=3840000, and Pr=0.7)?

A 20 °C water flows to 50cmx60cm flat plate with velocity of 6m/s . The flat plate surface temperature is maintained at 40 °C The water flows parallel to the 50cm side of the plate. If the kinematic viscosity of water is 78x10-8 m2/s, What is the local heat flux (Q/A) at the end of the plate (k=0.86 W/m deg C, Re=3840000, and Pr=0.7)?

Principles of Heat Transfer (Activate Learning with these NEW titles from Engineering!)

8th Edition

ISBN:9781305387102

Author:Kreith, Frank; Manglik, Raj M.

Publisher:Kreith, Frank; Manglik, Raj M.

Chapter7: Forced Convection Inside Tubes And Ducts

Section: Chapter Questions

Problem 7.20P

See similar textbooks

Similar questions

A 20degC water flows to 50cmx60cm flat plate with velocity of 6m/s . The flat plate surface temperature is maintained at 40deg C. The water flows parallel to the 50cm side of the plate. If the kinematic viscosity of water is 78x10-8 m2/s, What is the local heat flux (Q/A) at the end of the plate (k=0.86 W/m deg C, Re=3840000, and Pr=0.7)? Round your answer to 2 decimal places.
A 20degC water flows to 50cmx60cm flat plate with velocity of 6m/s . The flat plate surface temperature is maintained at 40deg C. The air flows parallel to the 50cm side of the plate. If the kinematic viscosity of water is 78x10-8 m2/s, at what length the flow become turbulent? If the average laminar heat transfer coefficient of water is 7740W/m2 degC, what is the overall heat transfer at the laminar section?
Consider Couette flow for two plates separated by a 6 inch-thick layer of 10W-30 oil. The top plate is pulled with a constant velocity of 3 m/s while the bottom plate is held stationary. What is the velocity of the fluid at a location 4 inches above the bottom plate?
Answer completely Show how the Darcy-Weisbach equation can be derived from the Hagen-Poiseuille equation through the introduction of the Reynolds number. What is the friction factor, f, equal to for flow at a laminar condition? What is it equal to in other regimes of flow?
A 20 °C water flows to 50cmx60cm flat plate with velocity of 6m/s . The flat plate surface temperature is maintained at 40 °C . The air flows parallel to the 50cm side of the plate. If the kinematic viscosity of water is 78x10-8 m2/s, at what length the flow become turbulent? If the average laminar heat transfer coefficient of water is 7740W/m2 °C , what is the overall heat transfer at the laminar section?
A fluid with a constant density of 961 kg/m3 and a constant viscosity of 1.419×10-3 Kg/m.s is flowing over a flat plate at a stream free velocity of 0.87 m/s. If the plate has a length of 2 m, answer the following: 1.What is Reynolds number at a point that is (1/4)L down the entrance? 2.Is the flow laminar or turbulent? 3.Calculate the thickness of the boundary layer in mm at (1/4)L down the entrance 4.Calculate the drag coefficient at (1/4)L down the entrance
For axial flow through a circular tube, the Reynolds numberfor the transition to turbulence is approximately 2300 based on the diameter and average velocity. Ifd= 5 cm and the fl uid is kerosene at 20 ° C, fi nd the volumeflow rate in m 3 /h that causes transition.
A 20degC water flows to 50cmx60cm flat plate with velocity of 3m/s . The flat plate surface temperature is maintained at 40deg C. The air flows parallel to the 50cm side of the plate. If the kinematic viscosity of water is 78x10-8 m2/s, at what length the flow become turbulent? Round your answer to 2 decimal places.
In an Osborne Reynolds Demonstration experiment, why is it the in laminar flow, the color collected has a color unlike in transitional and turbulent flow where the color of liquid is just transparent?
Consider a flow of SAE 30W oil at 20°C through a 2.4-cm-diameter smooth pipe at 1 million N/h. Determine the Reynolds number for this flow. For SAE 30W oil at 20°C, take ρ = 891 kg/m3, μ = 0.29 kg/m-s, and π = 22/7. The Reynolds number is
Q. 6 A 4.5-cm wide space between two plates is filled with SAE 30W lubricating oil at 26.7°C (Hoil = 0.301645 N.S/m2 ). What is the area of a very thin plate which is dragged by a force of 18 N through the oil at velocity of 16 m/min if the plate is 1.5 cm away from one of the fixed surfaces?
Consider laminar flow of a Newtonian fluid ofviscosity m between two parallel plates. The flow is onedimensional,and the velocity profile is given as u(y) = 4umax[ y/h - (y/h)2], where y is the vertical coordinate from thebottom surface, h is the distance between the two plates,and umax is the maximum flow velocity that occurs at midplane.Develop a relation for the drag force exerted on bothplates by the fluid in the flow direction per unit area of theplates.