A 200-kg block rests on a horizontal plane. Find the magnitude of the force P required to give the block an acceleration of 1.80 m/s² to the right. The coefficient kinetic friction between the block and the plane is 0.25. 30

A 200-kg block rests on a horizontal plane. Find the magnitude of the force P required to give the block an acceleration of 1.80 m/s² to the right. The coefficient kinetic friction between the block and the plane is 0.25. 30

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter7: Dry Friction

Section: Chapter Questions

Problem 7.50P: The block of weight W is pulled by the force P inclined at the angle to the horizontal. Find the...

See similar textbooks

Related questions

Q: A 150 kg table is resting on 60°sloping floor from vertical axis with coefficient of friction u= 0.6…

Q: Consider a 10-kg box sliding in a curve surface of radius 5.0 m as shown in the figure below. The…

A: Given: r= 5 m v = 4 m/s angle = 30 deg

Q: Find the downward acceleration of ml if it has a mass of 27.8 kg and the kinetic coefficient of…

A: Note: it is asked to determine the acceleration when the surface is frictionless. Consider the free…

Q: . Find the magnitude of the force P

A: Given that , Mass of blockm=100kg…

Q: A 10-kg body is pulled upward with an acceleration of 0.40 m/s. Calculate the tension in the cord.

A: Mass (m) = 10 kg Acceleration (a) = 0.4 ms2

Q: A 3.9-kg sphere S is being moved in a vertical plane by a robotic arm. When the angle 0 is 27°, the…

Q: A 2.6-kg sphere S is being moved in a vertical plane by a robotic arm. When the angle 0 is 39°, the…

A: Given:- Mass of sphere , m=2.6 kg,Angle subtended by robotic arm with horizontal axis, θ=39°,Angular…

Q: Two blocks are connected by a massless rope over a frictionless pulley, as shown in the diagram…

A: Given data, frictionless pulley Ma = 2 kg mass at block B Mb = 0.2 kg Angle of inclination θ= 30∘…

Q: In the diagram below, a force P of 750 N is applied to the 350 kg block. Find the acceleration of…

Q: ml kg m2 kg Calculate the vertical acceleration a of the cylinder m1 in m/s?, where m1 = 122 kg and…

Q: A 5.00 kg block is placed on top of a 10.0 kg block. A horizontal force of 45.0 N is applied to the…

Q: If the given system is released from rest in the position shown, calculate the velocity of B when it…

Q: 61" A 25° B

Q: A racecar is driving around a circular turn on a racetrack that has a radius of 35 m. Their initial…

Q: weighs 55.0N. Once block B is set to downward motion, it descends at a constant speed. A) Calculate…

Q: On a rough inclined plane (inclination angle a, kinetic friction constant u), a block (mass m1) is…

A: (a) Consider the free body diagram for the given system when the mass m1 slides upward, From the…

Q: 3- (KINETICS) The coefficient of friction under each of the weights shown in Fig. is 0,1. Solve of…

Q: Determine the vertical acceleration of the cylinder with a weight WA = 65 lb for each of the two…

Q: A force is applied to block A at angle of 40 degrees with the horizontal. Determine the friction…

A: Consider the free body diagram of the block A as shown below.

Q: Determine acceleration of a block of mass 4 kg resting on a rough horizontal floor (u= 0.23) which…

Q: Problem 2: The pulleys are frictionless and of negligible weight 150 kg C A 200 kg B 300 kg Find:…

Q: Block B rests on an A wedge. When the system is released and block A and B Since the static friction…

Q: Three friends ride a Ferris wheel with a diameter of 79m. Their combined mas with each car of the…

A: Given Data: The Diameter of a Ferris wheel is (d) = 79 m The Radius of a Ferris wheel is (r) =…

Q: In the system of connected bodies. The coefficient of kinetic friction is 0.20 under bodies B and C.…

Q: Block B rests on an A wedge. When the system is released and block A and B Since the static friction…

Q: Q5: Calculate the vertical acceleration a of the 100lb cylinder for each of the two cases…

Q: Block B rests on an A wedge. When the system is released and block A and B Since the static friction…

A: Given:-mA=70 kgmB=30 kgμs=0.1μk=0.8To find:-a) Acceleration of block Bb) Relative velocity of B wrt…

Q: 2. Bar AB starts from rest at 0 = 0 with the constant angular acceleration of 6 rad/sec?. The block…

A: Given, Angular acceleration of the bar , α=6 rad/s2 Mass of the block - m kg Initial angular…

Q: The conveyor belt shown below is inclined at an angle of 25 degrees. A 3kg package B is placed on…

Q: A 2.6-kg sphere S is being moved in a vertical plane by a robotic arm. When the angle 0 is 39°, the…

Q: A monkey stands hanging on a rope that passes through the reel. The weight of the monkey is balanced…

Q: 2.The block on the incline has a mass of 50 kg and the hanging weight 100 kg. The coefficient of…

Q: Three blocks on a frictionless horizontal surfsce are in contact with eachother as shown below. A…

Q: Assume that a driver (car modeled as a point mass) is negotiating a circular turn with a radius of…

A: Given:r=160 ftm=3800 lbμ1=0.85

Q: Determine the vertical acceleration of the cylinder with a weight WA = 71 lb for each of the two…

Q: The cart in figure 1 slides in the horizontal plane with an acceleration of 7 m / s². Body A…

A: Given data: m=7 kga=7 m/s2 Need to determine the horizontal force that the vertical wall exerts on…

Q: Calculate the vertical acceleration a of the 100-lb cylinder for each of the two cases illustrated.…

Q: MACHINE ELEMENTS CART A was being pulled by the BLOCK B. The weight of CART A is 500 lb. and the…

A: There are two types of forces that are acting on a circular surface. One type of force is Radial…

Q: A block of wood of mass 20 kg is supported as shown in the diagram. If the string suspending the 10…

A: Solution:

Q: Block A of mass m is placed on the inclined surface of wedge B. The static coefficient of friction…

A: Take the equilibrium of the forces along the y- direction

Q: In the system in which the first starts to move without speed, the masses of 10, 1 kg each, with the…

Q: Two forces, F, and F2, act on the 7.00-kg block shown in the drawing. The angles made by the forces…

A: Given data: Mass of the block, m = 7.0 kg. Mafnitufe of the force F1, F1 = 59.0 N. Magnitude of the…

Q: if the given system is released from rest in the position shown, calculate the velocity of A when it…

Q: Determine the vertical acceleration of the cylinder with a weight WA = 65 lb for each of the two…

Q: Find the downward acceleration of ml if it has a mass of 87.3 kg and the kinetic coefficient of…

A: Given: Mass of the block 1 is 87.3 kg. Coefficient of friction is 0.2. The system is shown below:

Concept explainers

Forming and Shaping

Metal forming is a category of metalworking process through which the material can be given the desired shape and size by subjecting it to plastic deformation, where the component undergoes bulk deformation process upon application of loads. Unlike the shearing and machining process, the material does not undergo up to a failure point as indicated in the stress-strain curve. Hence, the stresses induced during the forming process are greater than yield strength but less than the failure strength of the material. The process does not lead to the loss of material, so it can be said to be an economical process. During forming, the material is subjected to tensile forces, compressive forces, bending, and shearing loading conditions. The material should possess the property of ductility to undergo the forming process.

Question

Problem No. 1
A 200-kg block rests on a horizontal plane. Find the magnitude of the force P required to give the block an
acceleration of 1.80 m/s² to the right. The coefficient of kinetic friction between the block and the plane is 0.25.
P
30°

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

Two identical chairs, each weighing 14 lb, are stacked as shown. The center of gravity of each chair is denoted by G. The coefficient of static friction is 0.2 at B (the contact point between the chairs) and 0.35 at A, C, and D. Determine the smallest force P that would cause sliding.
Calculate the horizontal force P required to push the 85-lb lawn mower at constant speed. The center of gravity of the mower is at G, and the coefficients of rolling resistance are 0.12 for the front wheels and 0.18 for the rear wheels.
The 40-lb spool is suspended from the hanger GA and rests against a vertical wall. The center of gravity of the spool is at G and the weight of the hanger is negligible. The wire wound around the hub of the spool is extracted by pulling its end with the force P. If the coefficient of static friction between the spool and the wall is 0.25, determine the smallest P that will extract the wire.
The blocks A and B of weights WA and WB are joined by a rope that passes over the fixed peg C. The coefficients of static friction are =0.2 between block A and the inclined plane, and =0.25 between the rope and the peg. Determine the range of Wb/WA for which the system will be in equilibrium.
A uniform plank is supported by a fixed support at A and a drum at B that rotates clockwise. The coefficients of static and kinetic friction for the two points of contact are as shown. Determine whether the plank moves from the position shown if (a) the plank is placed in position before the drum is set in motion; and (b) the plank is first placed on the support at A and then lowered onto the drum, which is already rotating.
The 60-lb plank rests on a frictionless roller at A, and the 20-lb triangular support BD. Both bodies are homogenous. The coefficients of static friction are 0.4 at B and 0.3 at D. Determine the largest force P that can be applied to the plank without initiating motion.
The 3600-lb car with rear Wheel drive is attempting to tow the 4500-lb crate. The center of gravity of the car is at G, and the coefficients of static friction are 0.6 at B and 0.2 at C. Determine if the crate will slide.
Determine the smallest force P, applied to the plunger D, that will prevent the couple C=200Nm from moving the cylinder. Friction may be neglected at all surfaces, except between the plunger and cylinder. The masses of the bodies are negligible.
Find the largest value of b/h at which the folding table is in equilibrium. The coefficients of static friction are 0.5 at A and 0.3 at C. Neglect the weight of the table.
The coeffient of static friction between the uniform bar AB of weight W and the ground is 0.45. Find the smallest angle and the corresponding force P that would initiate simultaneous tipping and sliding of the bar.
The block of weight W is pulled by the force P inclined at the angle to the horizontal. Find the smallest force P and the corresponding angle that would cause impending sliding of the block. The angle of static friction between the block and the ground is s.
The mass of the unbalanced disk is m, and its center of gravity is located at G. If the coefficient of static friction is 0.2 between the cylinder and the inclined surface, determine whether the cylinder can be at rest in the position shown. Note that the string AB is parallel to the incline.