A 200 mm square structural tubing 8 m long is used as a column with the following properties: A = 9300 mm2 E= 200 GPa 1= 5.45 x 107 mm4 Fy = 415 MPa r= 77 mm What is the maximum height (m) required for the column with respect to the provision's limiting slenderness ratio for compression members? Assume fixed at the bottom and free end at the top (K = 2.0). 15.4 7.7 5.1 10.2

A 200 mm square structural tubing 8 m long is used as a column with the following properties: A = 9300 mm2 E= 200 GPa 1= 5.45 x 107 mm4 Fy = 415 MPa r= 77 mm What is the maximum height (m) required for the column with respect to the provision's limiting slenderness ratio for compression members? Assume fixed at the bottom and free end at the top (K = 2.0). 15.4 7.7 5.1 10.2

Steel Design (Activate Learning with these NEW titles from Engineering!)

6th Edition

ISBN:9781337094740

Author:Segui, William T.

Publisher:Segui, William T.

Chapter2: Concepts In Structural Steel Design

Section: Chapter Questions

Problem 2.1P: A column in a building is subjected to the following load effects: 9 kips compression from dead load...

See similar textbooks

Similar questions

From figure, given E=200 GPa, r=37.5mm, A= 2285mm^2 and I = 3.33 x 10^-6 m^4.Calculate the allowable centric load for the column and the corresponding stress using Euler’s formula by considering the factor of safety is 2.0
A circular metal column is to support a load of 500 tonne and it must not compress more than 0.1 mm. Given the MOE is 210 GPa, and the column is 2 m long. Calculate the cross sectional area and the diameter of the column. (0.467m2 and 0.771m) Note that 1 tonne= 1000 kg
Situation 17. A w12x79 of A573 Grade 60 (Fy-415MPa) steel is used as a compression member. It is 8m long pinned at the top fixed at bottom with additional lateral support at mid height in the weak direction. The properties are as follows Ag=14,500 sq.mm = 258.6x10^6 mm^4 Iy=84.375x10^6 mm^4 Calculate the critical slenderness ratio with buckling about strong axis. calculate the critical slenderness ration with buckling about weak axis. calculate the flexural buckling stress Fcr in MPA
The gross area Ag of the column is given as 165700 mm. Assume 1.5 % of steel reinforcernent, use 20 mm diameter steel bars, and calculate the number of bars.
A steel structural member is to be used as a column 5 m long. The column is to be pinned at both ends for bending about X-X axis and fixed at one end and pinned at the other for bending about Y-Y axis. The properties of the member section are as follows:E= 200 GPa, yield stress= 350 MPa, Ixx = 222 x 106 mm4, Iyy = 72.71x106 mm4 and A= 12.33 x 103 mm2Using Perry-Roberston equation, calculate the buckling stress and the corresponding load
Compute using Euler's formula: A square aluminum bar is to support a load of 65kN on a length of 4.50 m. Assume pinned ends, Determine the length of each side E = 70 GPa.
an 8 m long steel is pinned at the top and fixed at the bottom. the column is provided with lateral support 3m from the top in the weak direction. the properties of the column section are as follows: ix = 178.1x10^6 mm^4 ly = 18.8x10^6 mm^4 a = 8129 mm^2 fy = 400 mpa a. what is the critical effective slenderness ratio? %3d %3d b. what is the buckling stress of the column? c. calculate the critical load pc in kn
(c) A column pinned at both ends is as shown in Figure Q3. Determine whether the column is slender or not. Assume Le /r for slender column is > 30. Given E = 23 GPa and safety factor is 2. Determine the safety load for the column.
Determine the pure axial load capacity (kN) of the given tied column. Express your answer in whole number. B = 650 mm db = 32 mm f'c = 32 MPa fy = 420 MPa
Question 1) F=22 kN single load, M=26 kN.m moment and w=17 kN/m distributed load are acting on the beam whose loading condition is given in the figure. The length L is also given as L=5 m. The cross-sectional properties of the beam are; body height yg=239 mm, body thickness xg=17 mm, flange width xf=185 mm, flange height yf=15 mm. Point E on the section is located just below the flange-body junction. It is desired to determine the stress state in the section taken from the C level of the beam. According to this; Question 1-D) Find the moment of inertia of the beam section. (Do your operations by converting the lengths to meters. Take at least 4 digits for the decimal part of your result and use the expression E for the decimal part. Write it as 5E-3 instead of 0.005.)
Determine support reaction. P=800 lb , a=5 ft b=9 ft
A W 10 x 30 is used as a beam to support a concrete floor system. The floor is to carry a total load of 4.2 kPa. The beam is simply supported over a span of 8.4 m. The properties of the section are as follows: Depth = 254 mm Thickness of web = 19.2 mm Moment of Inertia = 98 x 106 mm4 Section modulus = 530 x 103 mm3 Weight = 44.86 k9/m Assume the beam is laterally supported over its length and that the allowable stress in bending is 0.66 Fy and in shear on gross section is 0.4Fy . Use A36 steel with Fy = 250 MPa. Determine the center-to-center spacing of the beams without exceeding the allowable shear stress. Determine the center-to-center spacing of the beams without exceeding the allowable bending stress. Which will be the center-to-center spacing of the beams to consider?