A 220 V series motor takes 15 A and runs at 700 rpm. The armature resistance including the resistance of the series winding is 0.8 ohm. At what speed will it run if a 2-ohm resistance is connected in series with supply voltage? Assume the motor is taking the same current.

A 220 V series motor takes 15 A and runs at 700 rpm. The armature resistance including the resistance of the series winding is 0.8 ohm. At what speed will it run if a 2-ohm resistance is connected in series with supply voltage? Assume the motor is taking the same current.

Delmar's Standard Textbook Of Electricity

7th Edition

ISBN:9781337900348

Author:Stephen L. Herman

Publisher:Stephen L. Herman

Chapter5: Resistors

Section: Chapter Questions

Problem 1PA

See similar textbooks

Related questions

Q: 2. Find the Norton equivalent of the circuit in Fig. 6Ω o a 6A 6Ω

Q: A sinusoidal voltage with maximum value (336 V), and a Frequeney its value (50 Hz), was applied on a...

A: As per the guidelines given to us, we can only provide the solution of first three subpart in multi ...

Q: Q1)Design moving coil ammeter as a voltmeter to read 15 V (RMS) alternating voltage. If the internal...

A: As per guidelines given by the company, we can only provide the solution of one question in multiple...

Q: Find load voltage VRL across RL D1 V1 R1 2500 16 Vrms }60 Hz 0° RL 1B4B42 D2 RD10 1000

Q: A spring-mass-damper system has transfer function as follow: 1 TF (3s²+4s+k) Spring constant is foun...

Q: Q2 A real diode for which the forward voltage drop is 0.7 V at 2.0 mA, what would be its current whe...

Q: e. Determine Zj and Ay for a common-emitter amplifier If Beta is 80

Q: A group of cells consisting of four rows connected in parallel, each row containing five cells conne...

Q: 1. Design a voltage regulator that will maintain an output voltage of 20 V across a 1-k load with an...

Q: a. Sketch the transfer and drain characteristics of an n-channel depletion-type MOSFET with /pss = 1...

A: MOSFET: It is a semiconductor, a special type of FET that works when the width of the channel and ch...

Q: Find the Laplace transform of the following:

Q: Estimate the stator current, equivalent rotor current, efficiency, output, and its power factor at a...

Q: If you have a diode of power rating 10 mW. The voltage across it is 0.7 V and the current passing th...

A: The solution is given below

Q: over one full cycle.

Q: 3. Calculate the load voltage, load current, and diode power in figure below using the second approx...

A: Solve the problem

Q: b. For the network below, determine Z, Zo, and Av. 2.7 k2 180 KSI 10 uF B- 200, a 10 uF 2.

Q: A sinusoidal voltage with maximum value (336 V), and a Frequency its value (50 Hz), w applied on a s...

A: As per company guidelines we can solve only first three sub parts kindly post another parts separate...

Q: Q1)Design moving coil ammeter as a voltmeter to read 15 V (RMS) alternating voltage. If the internal...

A: As per the guidelines, we can only provide the solution of one question in multiple type of question...

Q: Circuit diagram of HWR (without Capacitor): MA

Q: 9. The strength of longitudinal joint in Fig. 1-17 is 33.3 kips/ft, whereas for the girth is 16.1 ki...

A: Internal pressure, P=150.3 psi=150.3 lbin212 inft2=21643.2 lb/ft2

Q: The metering of a power customer was read and gave the following data: kW-hr = 200,000: kVAR-hr = 18...

Q: What is the RMS value of the voltage v(t) = 2 cos(3nt + )? %3D 1.41 V O 1.0 V O 2.0 V 2.82 V

A: Given voltage equation, vt=2 cos3πt+π2 V

Q: Consider the following circuit.

Q: why 8085 up have 16 bit Address than 80864p Contaim do bit Address

A: 8085 microprocessor: The 8085 is a 8 bit microprocessor which is produced by intel it is compatibl...

Q: c) Find the transfer function of figure 1.3 with the values given in part b x(t) f(t) Figure 1.3

A: The solution is given below

Q: S1 R1 L1 XSC1 Key = A 150 2H X2 Tektronix R2 20 V1 12V 3120V_100W

A: The circuit shown in figure represent a switch controlled circuit in which various elements are conn...

Q: Refer to Figure 1. A Y-connected source supplies 3 balanced 3-phase loads. The source has voltage Va...

Q: Voc RC R2 RE

Q: Lamp outlets Duplex convenience outlets Single gang switches Two gang switch Three gang switch ...

A: An electrical floor plan is given in the question. We need to determine the numbers of lamp outlets,...

Q: A 230 v, 10 hp d.c. shunt motor delivers power to a load at 1200 r/min. the armature current drawn b...

A: Given data, Terminal voltage V = 230 V Speed N = 1200 rpm. Armature current drawn by motor Ia=200 A ...

Q: If you have a diode of power rating 10 mW. The voltage across it is O.7 V and the current passing th...

A: In this question, We need to choose the correct options What is power dissipate if voltage across t...

Q: Consider the signal x(t) and its Fourier transform X(@). The Fourier transform X(@) of the signal is...

Q: PROBLEM: Find the equivalent transfer function, T(s) = C(s)/R(s), for the system shown in Figure 5.1...

Q: (3) The speed of the synchronous motor: a- Reduced linearly with the increase of load. b- Reduced in...

A: As per our company guidelines we are supposed to answer only first question kindly repost other ques...

Q: In cross circuits, how do i know the resistances are in parallel or in series connection?

A: The solution is given below

Q: 1. Refer to Figure 1. A Y-connected source supplies 3 balanced 3-phase loads. The source has voltage...

Q: x(1) = sin (xt) Which of the following graphs in the figure below best represents the amplitude spec...

Q: * Determine the operation status of the silicon diode in Figure below 10 k 10 k E 10 V 는20 V Forward...

A: Diode conducts only in one direction (unidirectional). Forward voltage drop of Si diode is VD(on) = ...

Q: Find V0 in the network using norton's theorem

A: In this question, We need to find V0 in the network using norton's theorem?

Q: Determine Vout for fig. 3 VEE 5V D1 R1 1.5kQ silicon diode Vout D2 R2 1.5kQ Germanium Diode Fig. 3

Q: j40 le a 30 I2 j20 0.51, 1220 v I3 d I 62 -j307 1020'v A I4 60 8 20°v Ix ell 'n

Q: Consider a system described by the equation y" (t) + 2y(t) = x (t) + a' (t). Using the convolution p...

A: The solution is given below

Q: A3kW, 400v/200v delta/star, 50 Hz, 3Φ , 6 pole induction motor is found to draw a line current of...

A: P= 3kW VBR =400 V IBR=25 mA pf=0.4 delta/star induction motor f=50 Hz P=6 T=25 Nm

Q: the circuit in Figure 1 with R = 470k2, C = 47µF and source voltage about 5V. Place the switch in th...

A: a. The circuit is shown below: The time constant of the circuit of the above RC circuit is calcula...

Q: (b) For the following filter circuit shown in Figure: 2(b), draw the wave shapes for Vo,in,i, and Vp...

Q: An inductive circuit has a resistance of 10 ohms and an inductance of 2 henrys. The total impedance ...

Q: 2. The star-connected rotor of an induction motor has a standstill impedance of (0.4+ j4) ohm per ph...

Q: Obtain the transfer function of the given electrical system below expressed in Laplace form s. Let i...

Q: 12. F = (W + Y) (X + Z) (W +X + Y)

A: The solution is given below

Q: Find the Unknown Resistor R3 Value on the circuit below.

Concept explainers

Three Phase Induction Motor

The induction motor is an electric motor that runs on AC (alternating current) and it is of two type single phase motor that work on single-phase power supply and three-phase motor that work on three-phase power supply.

Question

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step 3

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 3 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, electrical-engineering and related others by exploring similar questions and additional content below.

Similar questions

A motor is operating a load that requires a torque of 750 lb-in. and is turning at a speed of 1575 RPM. How much hp is the motor producing?
assume that a series motor is taking the same current with the conditions that 440v motor takes a 25 a and runs at 800 rpm the armature resistance including the resistance of the series winding is 0.77ohms calculate the speed will it run if a 1.88 resistance is connected in series with the supply voltage
A DC series motor of resistance 1 ohm across terminals runs at 1000 rpm at 250 V taking a current of 20 A. When an additional resistance of 6 ohm is inserted in series and taking the same current, the new speed would be ?
A 500 V shunt motor running at 720 rpm takes an armature current of 50 A. The equivalent armature resistance is 0.4 ohm. What resistance must be placed in series with the armature to reduce the speed to 540 rpm while maintaining the same torque?
A 120 V shunt motor has an armature equivalent of 0.5 ohm and a field resistance of 60 ohm. At full load, the motor takes 10 A and the speed is 1000 rpm. At what speed must this motor maybe driven as a generator to deliver 10 A to an external load at 120 V?
3. A shunt motor running at 600 rpm takes 80 A at 250 V. Armature resistance is 0.1 ohm. Shunt field resistance is 50 ohms. If the iron and friction losses amount to 2188 W determine the shaft torque. A. 250 N-m B. 224 N-m C. 254 N-m D. 204 N-m
The field windings of the series motor have a resistance of 120 ohms at 15-degree C. After running for two hours, the resistances increase to 140 ohms. If the temperature coefficient of the windings at 0 degree C is 0.004, find the new windings of the temperature
A DC series motor is running with a speed of 800 RPM, while taking a current of 20A from the supply. If the load is changed such that the current drawn by motor is increased to 50 A. Calculate the speed of the motor on new load. The armature and series field winding resistance are 0.2Ω and 0.3Ω respectively. Assume the flux produced is proportional to the current. Assume supply voltage is 250V.
A 230 V dc series motor has an armature resistance of 0.2 ohm and field resistance of 0.1 ohm at rated voltage. The motor draws a line current of 40 amperes and runs at a speed of 1000 rpm. Find speed of the motor for line current of 20 A at 230 V. Assume that flux at 20 A line current is 60% of flux at 40 A line current.
A d.c. series motor drives a load at 30 rev/s and takes a current of 10 A when the supply voltage is 400V. If the total resistance of the motor is 2 ohm and the iron, friction and windage losses amount to 300 W, the efficiency of the motor is?
A de electrical shunt motor rated 50 kW connected to a 250 V supply is loaded as to draw 200 A when running at a speed of 1250 rpm. Given: R = 0.22 ohms. Determine the load torque if the rotational loss (including iron loss) is 600 W.
A 110 V shunt motor has a field resistance of 55 ohms and armatureresistance of 0.1 ohm. The motor takes 20 A of current at 1000 rpm whiledeveloping full load torque. What is the motor speed when this motordevelops 70% of the full load torque.