A 230-V, 50-Hz, 4-pole, class-A, single-phase induction motor has the following parameters at an operating temperature 63°C : =2.51 ohms, r = 7,81 ohm, X 150.88 ohm, X- 4.62 ohm, X =4.62 ohms Determine stator main winding current and power factor when the motor is running at a slip of 0.05 at the specified temperature of 63°C. [3.74 248.24", 0.666] (AMIE Sec. B Elect. Machines (E-B) Summer 1991)

A 230-V, 50-Hz, 4-pole, class-A, single-phase induction motor has the following parameters at an operating temperature 63°C : =2.51 ohms, r = 7,81 ohm, X 150.88 ohm, X- 4.62 ohm, X =4.62 ohms Determine stator main winding current and power factor when the motor is running at a slip of 0.05 at the specified temperature of 63°C. [3.74 248.24", 0.666] (AMIE Sec. B Elect. Machines (E-B) Summer 1991)

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

A 3-phase induction motor, 440-V, 50-Hz, 6-pole, delta-connected has the following equivalent-circuit parameters at normal frequency:R1.2 ohm, R'2=0.18 ohm, X1= x'2=0.58 ohm, all per phase values. The machine is subjected in service to an occasional fall of 40% in both voltage and frequency. What total mechanical load torque is it safe to drive so that the machine just does not stall under these conditions? When operating at normal voltage and frequency, calculate the speed when delivering this torque and the power developed. Calculate also the speed at which maximum torque occurs. If V and f were both halved, what would be the increase in starting torque from the normal direct-on-line start at rated voltage and frequency? If now the machine is run up to speed from a variable-voltage, variable-frequency supply, calculate the required terminal voltage and frequency to give the 'safe' torque calculated above: (i) at starting, (ii) at 500 rev/min. Repeat (d) for the machine to develop a…
A 3300-V, 50-Hz, 3-phase, 4-pole, star-connected induction motor has identical primary and referred secondary impedances of value 3 + j9 ohm per phase. The turns-ratio per phase is 3/I (stator/rotor), and the rotor winding is connected in delta and brought out to slip rings. Calculate: the full-load torque at rated slip of 5%; the maximum torque at normal voltage and frequency; the supply voltage reduction which can be withstood without the motor stalling; the maximum torque if the supply voltage and frequency both fall to half normal value; the increase in rotor-circuit resistance which, at normal voltage and frequency, will permit maximum torque to be developed at starting. Express this: as a fraction of normal R2and as (3) ohmic values to be placed in series with each of the slip-ring terminals and star connected.
A 208-V, 50-Hz, 12-pole, Y-connected, three-phase induction motor has a stator impedance of 0.1 + j0.3 W phase and a rotor impedance of 0.06 + j0.8 R/phase at standstill. The core-loss resistance is 150 R/phase, and the magnetization reactance is 750 W phase. The friction and windage loss is 2 kW. When the motor operates at its full-load slip of 5%, determine (a) the power input, (b) the stator copper loss, (c) the rotor copper loss, (d) the air-gap power, (e) the power developed, (f) the power output, (g) the effi- ciency, (h) the shaft torque, and (i) the horsepower rating of the motor.
The equivalent circuit parameters of a 230-V, 1-phase, 6-pole, 60-Hz induction motor are: R1 = R2’ =10ohm, X1 = X2’ = 10ohm, and Xm = 100ohm. At a slip of 5%, calculate the developed torque and The input power to the motor at 230V, while running on no-load, is 31.4 W at 1.2 A. What is the approximate efficiency of the motor at 5% slip?
1. A 10-hp, 4-pole, 25-Hz, 3-Ф induction motor is taking 9,100 watts from the line. The core loss is 290 watts; stator copper loss is 568 watts; rotor copper loss is 445 watts, and the friction and windage loss is 121 watts. Determine the output torque in Newton-meter. 2. For a three-phase induction motor having rotor circuit resistance of 6 ohms, maximum torque occurs at a slip of 0.6. Find the value of standstill rotor circuit reactance. 3. A 4 - pole, 3 - phase, 60 Hz squirrel-cage motor draws 21 A and 7 kW while driving its normal load. Under these conditions, its slip is 2%. When running idle, this motor draws 6 A and 580 W at normal voltage. With its rotor blocked, this motor draws 15 A and 500 W with 50 V applied. What is the output torque of this motor when driving its normal load. 4. A 4-pole, 50 Hz, 3- phase induction motor develops a maximum torque of 110 N-m at 1360 rpm. The resistance of the star-connected rotor is 0.25 Ω /phase. Calicul the value of resistance that must…
A 75 kW, 440 V, 3-phase, 6-pole, 50 Hz wound rotor induction motor has a full load slip of 0.04 and the slip at maximum torque of 0.2 when operating at rated voltage and frequency with rotor winding short circuited at the slip rings. Assume the stator resistance and rotational losses to be negligible.power factor 0.8. Find(a) maximum torque (b) starting torque (c) full load copper loss. The rotor resistance is now doubled by adding an external series resistance. Determine (d) slip at full load (e) full-load torque (f) slip at maximum torque.
Type your question here Calculate the torque developed per phase for a 6-pole, 60 Hz, 3-phase induction motor at a slip of 5%, if the motor develops a maximum torque per phase is 250 N.m while running at 870 r.p.m.
A 110-V, 50-Hz single phase induction motor (split -phase) has the following constants for the main and auxiliary windings: Main winding, Zm (1.2 +j 25) ohm and auxiliary winding, Z,= (12+j 5) ohm. Determine (i) total current and power factor currents at time of starting, and (ii) phase angle between the main winding current and starting winding current.
A 3-phase, 260–V, 50-Hz, 22 HP, 6-pole, Y-connected induction motor has the following per phase parameters in ohms per-phase referred to the stator side: R1 = 0.04 Ω , R2 = 0.1 Ω , X1 = 0.223 Ω , X2 = 0.5 Ω , XM = 10 Ω The total friction, windage, and core losses can be assumed to be constant at 3 KW, independent of load. Find the starting code letter factor of this motor. Select one: a. Starting Code-Letter Factor is: C b. Starting Code-Letter Factor is: F c. None d. Starting Code-Letter Factor is: E e. Starting Code-Letter Factor is: D
oA % h.p ,110V, 60 Hz , 4-pole, capacitor start motor has the following constants and losses Ry =2.020 X, =2.790 Ry =4.120 Xy=212n Xy=86680 Rotational losses =37 W For a slip of 0.05. determine the stator current, power factor, power out put, speed, torque, and efficiency when this motor is running as a single phase motor at rated voltage and frequency with its starting winding open.
e specifications of a Y-connected three phase induction motor are as follows: 12-hp, 400-V, 17-A, 0.85-PF, 50-Hz, 1410-rpm, S1, Class E, IP22.(a) How many poles does this motor have?(b) Determine the rated torque and rated efficiency of the motor?
A 460 V, 60 Hz, Star connected, 870 r.p.m., Eight poles, Three-Phase Induction Motor has the following per phase parameters: R1 = 0.07, R2 = 0.05, X1 = X2 = 0.2, Xm = 6.5, Draw the approximate equivalent circuit and determine the following:I. Starting TorqueII. Maximum TorqueIII. Rated TorqueIV. Stator CurrentV. Power FactorVI. Input PowerVII. Magnetizing Current