A 230 V DC shunt motor has a full-load efficiency of 89.9%. Rated (full) load is 40 hp. Motor losses, expressed as a percentage of output power are as follows: rotational losses - 3.7%; armature copper loss - 3.9%; and, field copper loss - 2.5%. Stray load losses can be neglected. At full load, the motor speed is 1150 rpm. Neatly sketch an equivalent circuit for the DC shunt motor, and determine: the field current; the armature current at full load; the armature current at half load; the armature current at no load; and, the shaft torque at full load. 18 a. نه ن ن م نه b. C. d.

A 230 V DC shunt motor has a full-load efficiency of 89.9%. Rated (full) load is 40 hp. Motor losses, expressed as a percentage of output power are as follows: rotational losses - 3.7%; armature copper loss - 3.9%; and, field copper loss - 2.5%. Stray load losses can be neglected. At full load, the motor speed is 1150 rpm. Neatly sketch an equivalent circuit for the DC shunt motor, and determine: the field current; the armature current at full load; the armature current at half load; the armature current at no load; and, the shaft torque at full load. 18 a. نه ن ن م نه b. C. d.

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

The shunt field of a 5-hp dc compound motor has a resistance of 200 ohms, a series field resistance of 0.0018 ohms and an armature resistance of 0.5 ohms. If the motor develops a back emf of 200 V at a full load current of 50A, and a rotational loss of 400 W, determine: b. Ish (shunt field current)
(A Long shunt compounded DC motor has a nominal voltage of VT=100V. Its armature circuit total resistance is Ra= 3 ohm, serial field resistance Rs= 1 ohm. and shunt field resistance Rsh= 50 ohm . Find the shunt field circuit current (Ish) of the motor and write inside a box as given below, under rated load (full load) conditions. Draw the electrical equivalent circuit of the motor and write the resistance values of Ra, Rs and Rsh resistances on the correct places of the electrical equivalent circuit. Be careful about your solutions and drawings to be readable) Ish=?solve this question by using the rulers of Electromechanical Energy Conversion 2
ELECTROMECHANICAL ENERGY CONVERSION A shunt DC motor has a total resistance value for all conditions as Ra 2 0 and under full load conditions (nominal load) armature current is Ia - 10 A. The nominal terminal Voltage for the motor is VT 300 Vand total value for field circuit resistance for al conditions si Rf-150 . Under ful load conditions (nominal load), find the internal generated Voltage (EA), excitation circuit current (field current) (If), (total supply current flow, from electrical source) line current (li), electrical input power (Pin) supplied from the source.
a 220v, 500A,600r/min,separately excited dc motor has armarture and field resistance of 0.2 and 10 ohms repectively. The load is given by expression TL=2000-120n, where n is the speed in(revs/s). Speeds above the rated value are obtained by armature voltage control and speeds below rated value are calculated by field control. Calculate: a) motor terminal voltage and armatrue current when the speed is 450r/min. b) field winding voltage and armature current when the speed is 750 r/min.
A series dc motor 20-hp, 500-V, is having armature, series field and shunt field winding resistances of 0.08 Ω, 0.3 Ω and 125 Ω, respectively. If the back – emf is 478 V, determine the motor current when the connection is a) long – shunt. b) short – shunt c) series d) shunt
A certain shunt-connected dc motor has RA=4 Ω and VT=240 V. At a speed of 1000 rpm, the induced armature voltage is 120 V. Plot the torque–speed characteristic (Tdev versus nm) to scale.
A 80 kW, 480-V, 60-Hz, six pole induction motor has a slip of 5 percent when operating at fullload conditions. At full-load conditions, the friction and windage losses are 300 W, and the core losses are 400 W. For full-load conditions, compute the induced torque,T-ind, in N-m.
We have a six-pole, 440-V-rms, 60-Hz delta-connected synchronous motor operating with a constant developed power of 20 hp, unity power factor, and a torque angle of 10°. Then, the field current is reduced such that Br is reduced in magnitude by 25 percent. Find the new torque angle and power factor. Is the new power factor leading or lagging?
a 220v dc shunt motor takes 5a and 40a at no load and full load respectively it has an armature resistance of 0.2 ohm and field resistance of 110 ohm respectively. iron,friction and windages losses are negligible.then using among parameters find following. the ratio of emf at no load to full load
a 220v dc shunt motor takes 5a and 40a at no load and full load respectively it has an armature resistance of 0.2 ohm and field resistance of 110 ohm respectively. iron,friction and windages losses are negligible.then using among parameters find following. the armature current at no load
(A shunt DC motor has a total resistance value for all conditions as Ra=2ohm and under full load conditions (nominal load) armature current is la = 10 A. The nominal terminal Voltage for the motoris Vi=300 V and total value for field circuit resistance for all conditions is Rf=150 ohm Under full load conditions (nominal load), find the internal generated Voltage (EA), excitation circuit current(field current) (II), (total supply current flow, from electrical source) line current (IL), electrical input power (Pin) supplied from the source. Be careful about your solutions to be written readable andwrite the answers as it was shown below inside boxes.)EA-IH (IL) =Pin =
A shunt excited DC motor consumes 8Kw by feeding it from a 500V line and driving a load at 1000RPM. The counter electromotive force generated is 496V, the resistance of the excitation winding is 250Ω and its total losses account for 17% of the absorbed power. Determine: a) The resistance of the armature winding b) The useful torque c) Total copper losses..