A 24 ft column in a braced frame building is to be built into a wall in such a manner that it will be continuously braced in its weak axis direction but not about its strong axis direction. If the member is to consist of 50 ksi and is assumed to have fixed ends, select the lightest satisfactory W10 section available using the AISC Specification. Loads are PD = 175 k and PL = 130 k. Select the lightest satisfactory W8 section available.

A 24 ft column in a braced frame building is to be built into a wall in such a manner that it will be continuously braced in its weak axis direction but not about its strong axis direction. If the member is to consist of 50 ksi and is assumed to have fixed ends, select the lightest satisfactory W10 section available using the AISC Specification. Loads are PD = 175 k and PL = 130 k. Select the lightest satisfactory W8 section available.

Steel Design (Activate Learning with these NEW titles from Engineering!)

6th Edition

ISBN:9781337094740

Author:Segui, William T.

Publisher:Segui, William T.

Chapter4: Compression Members

Section: Chapter Questions

Problem 4.9.5P

See similar textbooks

Similar questions

Problem 7. One-story and two-bay frame is under distributed loading as shown in the figure below. The column height, L, is 10 ft. The beams are made of W18x50 (k-800 in4) and columns are made of W12x58 (I-425 in3,A=17 in?, x-5.23 inch, ry=2.48 inch). All the structural members are made of grade 50 steel (Fy-50 ksi and Fu-65 ksi). The columns are fully braced with respect to bending in y direction. (a) Identify the effective lengths and slenderness in x and y directions of column ab. (b) Calculate the compressive strength of column ab, pPn- the frame can carry based on the compressive (c) Identify the maximum distributed load, Wu, capacity of column ab. 4at-10 Wu W18x50 a b 25 ft 25 ft
USE NSCP 2010 A rectangular beam reinforced for both tension and compression barshas an area of 1450 mm² for compression bars and 4350 mm² fortension bars. The tension bars and compression bars are placed at a distance of 600 mm and 62.5 mm respectively from the top of thebeam. The beam width 300 mm, fc’ = 21 MPa, fy = 415 MPa andtension steel covering is 60 mm.If it is 8 m-simply-supported beam that carries three concentratedservice live loads P applied at three quarter points of the beam (exceptat the supports), neglecting the self weight of the beam, determine themaximum value of service load P in kiloNewtons.
The Advantages and disadvantages of Teel Braced Frame
If the beam in Problem 5.5-9 i5 braced at A, B, and C, compute for the unbr Cb aced length AC (same as Cb for unbraced length CB). Do not include the beam weight in the loading. a. Use the unfactored service loads. b. Use factored loads.
Problem 3b. The built-up shown has Fy=50 ksi MC18X 42.7 W12 X 72 KL = 18.5 ft %3D Find the following: a. The KL/r b. The design strength for LRFD. c. The allowable strength for ASD. d. Is the section? Why?
Use 2015 NSCP A simply supported beam is subjected to a uniform service dead load of 1.0 kip/ft(including the weight of the beam) a uniform service live load of 2.0 kips/ft and a concentrated service dead load of 40 kips. The beam is 40ft long and a concentrated load is located 15 ft from the left end. The beam has continuous lateral support and A36 steel is used. Is W30x108 adequate? a) Use LRFD b) use ASD P₁=40* -15- 25'- WD = 1.0km W₁ = 2.0³m W30 x 108 40'-
The floor structural system shown in Fig 1 comprise W-section steel beams and girders supporting a 5-inch thick concrete slab which provides full restraint to the flanges of the beams. The density of concrete is 150 lbs./ft³. and the uniformly distributed live load L- 50 lbs/ft². L-22¹ 12' A. Beam B2 Gl GI [BI] FIG. 1-Steel Floor Beam 12' + (a) Strength Design i. Flexure (Bending) ii. Shear iii. Serviceability Design - Deflection --I 1) Produce a sketch of the floor plan showing the tributary load distribution areas for the beams and girders [B2] 2) Using AISC LRFD methodology design the following structural members using W-section A992 steel (Fy = 50 ksi). Assume the beams are cambered to offset dead load deflection. Use Design Tables in your solution.
AW14 x 43 column in a braced frame has a yield stress of 50 ksi and a height of 10 ft. The column is pinned at the top and bottom and has no intermediate bracing. Determine the available strength of the column considering the critical stress for flexural buckling. From AISC Manual Table 1-1, the properties of a W14 x 43 are: A = 12.6 in^2 tw = 0.305 in bf/2tf = 7.54 h/tw = 37.4 rx = 5.82 in ry = 1.89 in Ix = 428 in4 ly = 45.2 in4 G= 11,200 ksi J = 1.05 in^4 Cw=1950 in^6 What is the nominal axial strength considering flexural buckling stress of the column section (in kips). O 310 O 468 O 447 O 375 O 420 O 436 O 517 O 280
Please help me with my problem with complete solution and please use the nscR and gisc shapes database. Select the lightest w section (with Ey = 345 MPa) for the beams and girders shown in the figure. The floor slab is 150mm reinforced concrete and supports a 0.80 MPa uniform live load. Assume that continuous lateral bracing of the compression flange is provided. The maximum permissible deflection is L/250. Use LRFD method only. 10.00 m E 2. 2.
A simply supported beam is subjected to a uniform service dead load of 1.0 kips/ft (including the weight of the beam) and uniform service live load of 2.5 kips/ft. The beam is 40 feet long, The beam has continuous lateral support, and A572 Grade 50 steel is used. A572 Grade 50 steel has Fy = 50 ksi and Fu = 65 ksi. Is a W30 × 116 adequate from flexure and shear?Check both LRFD and ASD. Is the beam adequate from deflection if it allowsmaximum deflection of L/360 (dead load + liveload)?
An A36 W14X605 simply supported steel beam with span “L” carries a concentrated service liveload “PLL” at midspan. The beam is laterally supported at supports and its midspan. Consider its beam selfweight to be its service deadload, “w” (use ASEP steel manual for selfweight, w and other section properties). In checking section's compactness, calculate the upper limit for non-compact web category? Express your answer in 2 decimal places.
Q2) The members of the truss structure shown below is plain concrete. The compressive strength of the concrete is 25 MPa. Compute the maximum load P that can be carried by the structure. (Cross section of each member of the truss is 200 x 200 mm and don't use material factors and do not consider slenderness) Comment on your results briefly. P A& 2m SC 2 m 1380 2m D