A 240 V, 50 Hz, single-phase capacitor start a.c. motor is loaded such that the ship is 6% The motorconstants referred to the stator are:Stator resistance = 2-22; Rotor resistance = 3-852Stator reactance = 3.0; Rotor reactance = 2-12Magnetising reactance = 862; Iron and friction loss = 50 WDraw the equivalent circuit and from it find the output power and efficiency at the given loading.

Answered: Image /qna-images/answer/a4d46b23-f8c3-4289-87a6-41125d095b3a.jpg

A 240 V, 50 Hz, single-phase capacitor start a.c. motor is loaded such that the ship is 6% The motor constants referred to the stator are : Stator resistance = 2-22; Rotor resistance = 3-852 Stator reactance = 3-002; Rotor reactance = 2-1 2 Magnetising reactance = 862; Iron and friction loss = 50 W Draw the equivalent circuit and from it find the output power and efficiency at the given loading.

A 240 V, 50 Hz, single-phase capacitor start a.c. motor is loaded such that the ship is 6% The motor constants referred to the stator are : Stator resistance = 2-22; Rotor resistance = 3-852 Stator reactance = 3-002; Rotor reactance = 2-1 2 Magnetising reactance = 862; Iron and friction loss = 50 W Draw the equivalent circuit and from it find the output power and efficiency at the given loading.

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

a)the figure below shows the per-phase equivalent circuit of a two - pole three- phase induction motor operating at 50 Hz . The voltage (E1) across the magnetizing inductance is 210 v , and the slip (s) is 0.05 . What is the developed torque produced by the motor ? b) A 4 poles , 50Hz , Y-connected three phase induction motor has the per phase equivalent circuit parameters of (R1 =R2=0.12 , X1=X2=0.6 , Xm =12 ) ohm and I2 =20 (0 . Use exact equivalent circuit to determine the following at rated slip of 0.03 : I. Stator current II. Magnetizing current III. Power factor IV. Developed torque C) What is the physical meaning for each of the following induction motor parameters : R1 , R2 , Rc , X1 , X2 , Xm d) What is synchronous watt
A 2000V 3-phase 4-pole wye connected SM runs at 1800 rpm. The excitation is constant and gives an emf per phase of 1150V. The resistance is negligible compared to synchronous reactance of 3Ω/ . Determine the following when the armature current is 200A. a. Input power per phase b. Torque develop per phase
A 200V, 3, star connected induction motor takes 30A at a line voltage of 35V with rotor locked. With this line voltage, power input to motor is 450W and core loss is 60W.The dc resistance between a pair of stator terminals is 0.15Ω. If the ratio of ac to dc resistance is 1.6, find the equivalent leakage reactance/phase of the motor and the stator and rotor resistance per phase.
A 3-phase, 6 pole, 440 V, 60 Hz, Y-connected induction motor has the following impedances per phase referred to the stator circuit: R1=0.43 Ω, R2=0.54 Ω, X1=1.263 Ω, X2=0.608 Ω, XM=43Ω The total rotational losses are 1100 W and are assumed to be constant. The core loss is lumped in with the rotational losses. For a rotor slip of 2 percent at the rated voltage and rated frequency, Find the motor speed, stator current, output power
A 2000V 3-phase 4-pole wye connected SM runs at 1800 rpm. The excitation is constant and gives an emf per phase of 1150V. The resistance is negligible compared to the synchronous reactance of 3Ω/. Determine the following when the armature current is 200A. a. Input power per phase b. Torque develops per phase
What will be the operating power factor of a 3-phase induction motor, whose ratings are 230 V, 50 Hz, 120 hp, and 4-poles? Motor is operating at rated conditions with an efficiency of 92% and draws a line current of 260 A. The core loss and stator copper losses are 1710 W and 2830 W respectively. (a) 0.85 (c) 0.93 (b) 0.90 (d) 0.80
(Draw the Circuit Diagram) A self-excited shunt generator has a field resistance of 60 ohms. When the generator delivers 6 kW, the terminal voltage is 120 V, while the generated emf is 133 V. Determinethe armature resistance
A 500-V, wave-wound, 750 r.p.m. shunt generator supplies a load of 195 A. The armature has 720 conductors and shunt field resistance is 100 Ω. Find the demagnetising amp-turns/pole if brushes are advanced through 3 commutator segments at this load. Also, calculate the extra shunt field turns required to neutralize this demagnetisation.
DEGREE: BS Electrical Engineering COURSE/SUBJECT: AC Machines illustrate/draw the problem. Solving is optional, solved in previous post problem already PROBLEM: A 3-phase, 50 Hz, P=4 slip ring IM has a star connected rotor. The full load speed of the motor is 1460 rpm. The rotor resistance and standstill reactance per phase are 0.1 ohm and 1.5 ohm, respectively. The open circuit voltage on open circuit between the slip rings is 90 volts. Find: (A) Rotor current, and (B) Full load power factor.
The stator and rotor winding numbers of a 380 V, 50 Hz, 3-phase, 4-pole, 1440 rpm, Y-connected ring ASM are 300 and 120 sipir, respectively. One phase resistance of the rotor is 2 ohms and its inductance is 0.035H. When the resistance of the rheostat in the rotor circuit is 3 ohms; Find a-) copper losses of the rotor circuit in the first development, b-) rotor copper losses when feeding the full load of the motor.
A 480V synchronous generator. 200 kVA, 0.8 power factor lagging, 60 Hz, two poles. connected in Y. It has a synchronous reactance of 0.25Ω and an armature resistance of 0.04Ω at 60 Hz, its own friction losses and with the air are 6 kW and its core losses are 4 kW. The field circuit has a voltage of 200 V and the maximum Is is 10 A. The field resistance is adjustable in a range of 20 to 200 Ω. The generator occ is shown in the figure below.Assume that the field current of the generator from the problem in the previous task has been set to 4.5A.a) What will be the voltage at the terminals of the generator if it is connected to a load at A with an impedance of 5<30° Q?b) Draw the phasor diagram of this generator.c) What is the efficiency of the generator under these conditions?d) Suppose now that another charge at A, identical, is placed in parallel with the first one. What happens in the phasor diagram of the generator?e) What is the new terminal voltage after adding charge?…
A 480V synchronous generator. 200 kVA, 0.8 power factor lagging, 60 Hz, two poles. connected in Y. It has a synchronous reactance of 0.25Ω and an armature resistance of 0.04Ω at 60 Hz, its own friction losses and with the air are 6 kW and its core losses are 4 kW. The field circuit has a voltage of 200 V and the maximum Is is 10 A. The field resistance is adjustable in a range of 20 to 200 Ω. The generator occ is shown in the following figure…Assume that the field current of the generatoradjusts to achieve nominal 480V voltage under full load conditionsfor each of the questions below.a) What is the efficiency of the generator at nominal load?b) What is the voltage regulation of the generator if it is loaded with nominal KVAwith charges with a FP of 0.8 behind?c) What is the voltage regulation of the generator if it is loaded with nominal KVAwith charges with a FP of 0.8 in advance?d) What is the voltage regulation of the generator if it is loaded with nominal KVA with loads with a…