A 3-phase, 4 pole, 230 V, 60 Hz wound-rotor induction motor has both its stator and rotor connected in Y. The rotor has half as many turns per phase as the stator. If the rotor is running at 1725 rpm, Rr is 0.075 ohms and Xs = 0.375 ohms, determine the torque developed by the motor. Answer: 27.543 lb ft

A 3-phase, 4 pole, 230 V, 60 Hz wound-rotor induction motor has both its stator and rotor connected in Y. The rotor has half as many turns per phase as the stator. If the rotor is running at 1725 rpm, Rr is 0.075 ohms and Xs = 0.375 ohms, determine the torque developed by the motor. Answer: 27.543 lb ft

Delmar's Standard Textbook Of Electricity

7th Edition

ISBN:9781337900348

Author:Stephen L. Herman

Publisher:Stephen L. Herman

Chapter32: Three-phase Motors

Section: Chapter Questions

Problem 13RQ: A squirrel-cage induction motor is operating at 1175 RPM and producing a torque of 22 Ib-ft. What is...

See similar textbooks

Similar questions

A 3-phase, 4-pole, 50-Hz induction motor has a star-connected rotor. The voltage of each rotor phase at standstill and on open-circuit is 121 V. The rotor resistance per phase is 0.3 Ω and the reactance at standstill is 0.8 Ω. If the rotor current is 15 A, calculate the speed at which the motor is running. Also, calculate the speed at which the torque is a maximum and the corresponding value of the input power to the motor, assuming the flux to remain constant.
A 3-phase, 4-pole, 230-V, wound rotor induction motor has both its stator and rotor connected in Y. The stator has half as many turns per phase as the rotor. It has a rotor resistance and blocked rotor reactance of 0.09 and 0.385 ohm respectively. If the rotor is turning at 1760 rpm, determine the rotor power developed in hp. *
A 209-V, three-phase, six-pole, Y-connected induction motor has the following parameters: R1 = 0.128 Ω, R’2 = 0.0935 Ω, Xeq =0.49Ω. The motor slip at full load is 2%. Assume that the motor load is a fan-type. If an external resistance equal to the rotor resistance is added to the rotor circuit, calculate the following: a. Motor speed, Starting torque, Starting current, and Motor efficiency (ignore rotational and core losses) b. Calculate the value of the resistance that should be added to the rotor circuit to reduce the speed at full load by 20%. Find the motor efficiency. c. If the voltage is reduced by 20%, calculate the Motor speed, Starting torque, Starting current, and Motor efficiency (ignore rotational and core losses) d. If the supply frequency is reduced by 20%, calculate the Motor speed, Starting torque, Starting current, and Motor efficiency (ignore rotational and core losses) ..
A 4 pole three-phase cage rotor induction motor running at full-load draws a stator current of 80 A at apower factor of 0.83 lagging from a 440 V, 50Hz supply. Under this condition the stator loss is 4 kW,the rotor loss is 1.5 kW, and the percentage slip is 5%. If the shaft output power is 32 kW, calculate (a)the shaft output torque, (b) the efficiency, and (c) the mechanical (friction and windage) loss.
A 40-HP, 230-V., 8-pole, 25 Hz three-phase induction motor is running at 355 rpm at rated load. The torque lost by friction is 24 N-m. If the stator losses amount to 1,000 W., calculate the efficiency of the motor at this load.
Solve the following problems with complete solutions using two(2) decimal digits. 1. The rotor of a 220-V., 60 Hz, 4-pole induction motor has a power input of 80 kW is observed that the rotor emf makes 90 cycles per minute. Calculate the rotor copper loss. 2. A 40-HP, 230-V., 8-pole, 25 Hz three-phase induction motor is running at 355 rpm at rated load. The torque lost by friction is 24 N-m. If the stator losses amount to 1,000 W., calculate the efficiency of the motor at this load. 3. A 6-pole, 50 Hz, 3-phase induction motor runs at 960 rpm while delivering a shaft torque of 120 N-m. If friction and windage loss amount to 180 W., determine the rotor copper loss.
A 180 watts, 110 V, 60 Hz, 4-pole, 1-phase induction motor has the following constants:R1= 2.02 Ω, X1= 2.79 Ω, R2 ’= 4.12 Ω, X2 ’=2.12 Ω, XM = 66.8 Ω, core loss= 24 watts,friction and windage loss= 13 watts for a slip 0f 0.05 per unit, determine the stator current,power factor, power output, speed, torque and efficiency, when the motor is running atrated voltage and frequency.
If Rs=Rr=0.35 ohm, Xs=Xr=0.7 ohm, Xm=50 ohm and Re=150 ohm in a 3-phase, 50 Hz, 224 volt rated and 6-pole star connected squirrel cage induction motor; where the rotor speed is 987 rpm; Using the T equivalent circuit, this motor a) the active power drawn from the source, b) the moment produced in the shaft, calculate. Note: Use the T equivalent circuit.
3 DECIMAL PLACES: The useful full-load torque of 3-phase, 6-pole, 50-Hz induction motor is 242.84 Nm. The rotor emf is observed to make 90 cycles per minuteCalculate (a) motor output b) Cu loss in rotor (c) motor input and (d) efficiency if mechanical torque lost in windage and friction is 28.36 Nm and stator losses are 890W.
A 3-phase, 4 pole, 230 V, 60 Hz wound-rotor induction motor has both its stator and rotor connected in Y. The rotor has half as many turns per phase as the stator. If the rotor is running at 1725 rpm, Rr is 0.075 ohms and Xs = 0.375 ohms, determine the torque developed by the motor. The result should be in lb-ft The answer given was 27.543 lb-ft
A 3-phase, 4 pole, 230 V, 60 Hz wound-rotor induction motor has both its stator and rotorconnected in Y. The rotor has half as many turns per phase as the stator. If the rotor is runningat 1725 rpm, Rr is 0.075 ohms and Xs = 0.375 ohms, determine the torque developed by themotor.
A 40Hp, 230V, 10pole, 50Hz three-phase induction motor is running at 585 rpm at rated load. If the stator loss amounts to 1000W and the efficiency of the motor at this load is 90%. Determine the torque lost by friction in lb-ft