A 30-m steel tape standardized at 20°C and supported throughout under a tension of 5.45 kg was found to be 30.012-m long. The tape had a cross-sectional area of 0.050 cm? and a weight of 0.03967 kg/m. This tape was held horizontal, supported at the ends only, with a constant tension of 9.09 kg, to measure a line from A to B in three segments. The following data below were gathered from the field. Measured Temperature Section Distance (m) ("C) А-1 30 14 1-2 30 15 2-B 21.151 16

A 30-m steel tape standardized at 20°C and supported throughout under a tension of 5.45 kg was found to be 30.012-m long. The tape had a cross-sectional area of 0.050 cm? and a weight of 0.03967 kg/m. This tape was held horizontal, supported at the ends only, with a constant tension of 9.09 kg, to measure a line from A to B in three segments. The following data below were gathered from the field. Measured Temperature Section Distance (m) ("C) А-1 30 14 1-2 30 15 2-B 21.151 16

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A 30-m steel tape weighing 0.04 kg/m is constantly supported only at its end points, and used to measure a line with a steady pull of 8.5 kg. If the measured length of the line is 2465. 18 m, determine the correct length of the line. Please include the complete solution
Elementary Surveying: Measurement of Horizontal Distances, show proper and right solution. 1. A heavy 50-m tape having a cross-sectional area of 0.07 cm2 has beenstandardized at a tension of 6.4kg. If the E = 3.20 x10^6kg/cm2,determine the elongation of the tape if a pull of 15kg is applied.
11 A cylindrical caisson having an outside diameter of 9 m floats in sea water with its axis vertical and its lower end submerged 9 m, below the water surface. If its center of gravity is on the vertical axis and is 3.6 m above the bottom. a. Determine the value of ??? b. Find the true metacentric height. c. Find the righting couple when the caisson is tipped through an angle of 8°
The taped distance of a line is 198.175 m using a 50 m steel tape weighing 2.4 kg with a cross sectional area of 0.036 cm2 at 32°F with a pull of 8 N is applied, supported at 20 m interval during the measurement. The angle of the tape during measurement is 11°20′. The tape is exactly 50 m at a temp of 28°F at standard pull of 5 N, find the following: a) Correction due to combined correction of the tape b) Correction due to slope c) The correct horizontal distance of the line
In every measurement, 100 m tape is suspended at the ends under a pull of 15 kg. It also supported at 30 m and 75 m marks. If the tape is used to measure a 543.25 m long line, determine the total correction due to SAG? The tape weighs 5 kg.
elementary surveying A 30-m tape weighing 1.5kg is of standard length under a pull of 6kg, supported for full length. The tape was used in laying a line 2,893.4m long on smooth level ground under a steady pull of 17kg. Assuming E = 3.2x10⁶ kg/cm² and the unit weight of steel to be 7.9x10⁻³ kg/cm³. 1.Determine the correction for increase in tension. 2.Determine the correct length of the line measured.
The measured length of an inclined distance was recorded to be 417.698 m long. The difference in elevation between the initial and end points was found to be 1.72 m. The 25 m tape is of standard length at temperature 13 ˚C. During measurement the temperature reading was 20˚C and the tape was supported at both ends with an applied pull of 72N. The tape has a weight of 0.549 kg/m. (K=0.0000116 m/˚C) Determine the corrected horizontal distance (in meters)
a 50 m steel tape weighing 0.035 kg/m is constantly supported at mid- length and its end points, and is used to measure a line AB with a ready pull of 6.5 kg. if the measured length of AB is 1268.256 m. determine the total sag correction for the whole length measured.
A 30-m steel tape weighing 1.75 kg is of standard length under a pull of 4.55 kg, supported for full length. This tape was used in measuring a line (found to be 1371.50 m) on smooth level ground under a steady pull of 8 kg. Assuming E = 2.05x106 kg/cm2 and that the unit weight of steel is 7.9x19-3 kg.cm3, determine the following: cross-sectional area of the tape, correction for increase in tension for the whole length measured, and the correct length of the measured line. Please include the complete solution
A 30-m tape is supported only at its ends under a steady pull of 8-kg. If the tape weighs 0.91-kg, determine the sag correction and the correct distance between the tape ends of the tape. Illustrate.
A 50-m steel tape weighs 1.05 kg and is supported at its endpoints and the 10-m and 25-m marks. If a pull of 6.0 kg is applied at the ends of the tape, what is the correction due to sag for a full tape length? a. 0.060 m b. 0.064 m c. 0. 050 m d. 0.500 m
Q1/Find the horizontal displacement at C . and @y by using Virtual Work Method, i you know E - 200 GPa, I - 25°(10% mmé , (P KN)