AW30°В10 ft-12 ftThe structure above is supported by a pin at point A and a roller at point B.If the maximum force that the roller at point B can support is 10 kips, which of thefollowing is closest to the maximum intensity w of the distributed load?O a) 2.77 kip/ftO b) 4.13 kip/ftc) 2.23 kip/ftd) 1.00 kip/ft

To find the Value of inclined UDL intensity Take moment about A , because support A is hing so…

Answered: А 30° В 10 ft 12 ft

Engineering

Civil Engineering

А 30° В 10 ft 12 ft

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

1. The boom of the wall crane 4m long is held at right angles to the wall by a wire that is attached to the wall 3m above the foot of the boom. If the load lifted is 45000N, find the tension in the wire and the compression force in the boom Neglect the weight of the boom. Draw the FBD
compute the maximum moment (kN-m, magnitude only) at C due to a uniform dead load of 12 kN/m, uniform live load of 15 kN/m and a concentrated load of 99 kN by influence lines. Use a = 3m., and b = 11m.
1.What is the maximum intensity of moment for the beam loaded as shown? -20 KN-m -40 KN-m -80 KN-m -72 KN-m 2.What is the shear value at point just before C? 40KN 72KN 80KN 32KN 3.What is the shear value at point just after D? 80KN 72KN 32KN 40KN 4.What is the moment value at B? -72 KN-m -40 KN-m -20 KN-m -80 KN-m 5.What is the value of x, the additional point of zero shear from C? 3.0 m 1.6 m 2.67 m 2.4 m 6.What is the degree of curve in the shear diagram…
Determine the moments at all supports. Answer key: MBA = 2 kN-m; MBC = -2 kN-m; MCB = 4.46 kN-m; MCD = -4.46 kN-m; MDC = 0.66 kN-m; MDE = -0.66 kN-m; MED = 3.27 kN-m
A 300 mm x 300 mm concrete column which is pin connected at both ends has an unsupported length of 4.6 meters. The column is carry a total factored axial load Pu = 300 kN and a lateral concentrated load of 90 kN acting at the mid-height of the column. Assume fc’ = 21 MPa and Bdns = 0.15. Compute the total moment including the secondary moment due to lateral deflection.a. 75.852 kN.m. c. 124.614 kN.m.b. 635.785 kN.m. d. 90.872 kN.m
Draw the influence line diagram of the given beam below for it's shear andmaximum moment about the point E, and determine the equivalentmaximum moment at point E due to a dead load of 10 kn/m and a movinglive load of 8 kn/m with two concentrated load of 90 kn and 80 kn that is 1mapart.ILD for Ve=f(x) and Me=f(x), (Point D is an internal pin)A. The maximum positive and negative ordinate of the influence linediagram from Ve=f(x)B. The maximum positive and negative ordinate of the influence linediagram from Me=f(x)C. The equivalent maximum moment of Me which is 4m away from the hingesupport due to the applied loading conditions?
The shear capacity V if a steel wide flange section, 600 mm deep whose web is 9 mm thick, is closest to: Assume fy = 200 MPa. Take FV = 0.4 Fy a. 645 kN b. 413 kN c. 507 kN d. 432 kN
The tripod shown is to support a vertical load W and horizontal load P at point D. The legs of the tripod rest on a level rough surface at points A, B and C. If W=150N, P=50N, a = 0.5m, b =0.75m. c=1.125m, d=1.5m, 19. Determine the force acting on leg AD. Determine the force acting on leg BD.
A uniform 50-kgf board rests on rough supports located at A and B in the figure. Thefriction coefficient μs=0.60 on both contact surfaces. If a man weighing 80 kgfpulls on the rope with a force of 40 kgf, determine:a) The angles "min" minimum and "max" maximum for which the system is in equilibrium.b) The minimum coefficient of friction that must exist between the soles of the man's shoes andthe soil for each of the cases in section a.
The towline exerts a force of P = 6 kN at the end of the8-m-long crane boom. If u = 30°, determine the placementx of the hook at B so that this force creates a maximummoment about point O. What is this moment?
If the roller at A and the pin at B can support a load up to 4 kN and 8 kN, respectively, determine the maximum intensity of the distributed load w, measured in kN/m, so that failure of the supports does not occur.
Which section below has the larger negative moment capacity?