A 300 lb block is placed on an inclined planed surface with a slope of 3 vertical and 4 horizontal. If 100 Ib force is applied to the block parallel to the inclined planed surface. Determine whether the block is in equilibrium, and find the value of the friction force, if the Coefficient of friction between the block and plane surface are us = 0.25 and ux = 0.20. 300 lb 100 lb

A 300 lb block is placed on an inclined planed surface with a slope of 3 vertical and 4 horizontal. If 100 Ib force is applied to the block parallel to the inclined planed surface. Determine whether the block is in equilibrium, and find the value of the friction force, if the Coefficient of friction between the block and plane surface are us = 0.25 and ux = 0.20. 300 lb 100 lb

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter7: Dry Friction

Section: Chapter Questions

Problem 7.73P: The normal pressure acting on the disk of the sander is given by p=(4/3)+(r2/6), where p is the...

See similar textbooks

Similar questions

The normal pressure acting on the disk of the sander is given by p=(4/3)+(r2/6), where p is the pressure in pounds per square inch (psi) and r represents the radial distance in inches. Determine the torque C required to operate the sander at constant speed if the kinetic coefficient of friction for the surface being sanded is 0.86.
The leather rein used to fasten the horse to the hitching rail weighs 3.5 oz per foot. The coefficient of static friction between the rail and the rein is 0.6. If a 34-lb force acting on the bridle is sufficient to restrain the horse, determine the smallest safe length L for the free end of the rein.
The single-plate clutch transmits the torque C from the input shaft on the left to the output shaft on the right. Compression springs between the clutch housing and the pressure plate provide the necessary pressure on the friction surface. The splines prevent the clutch plate from rotating relative to the output shaft. If Ri=4 in. and R0=9 in., determine the total force that must be applied to the pressure plate by the springs if the clutch is to transmit a torque of C=56lbft when it is new.
Two hemispheres having an inner radius of 2 ft and wall thickness of 0.25 in. are fitted together, and the inside pressure is reduced to -10 psi. If the coefficient of static friction is ms = 0.5 between the hemispheres, determine (a) the torque T needed to initiate the rotation of the top hemisphere relative to the bottom one, (b) the vertical force needed to pull the top hemisphere off the bottom one, and (c) the horizontal force needed to slide the top hemisphere off the bottom one.
Box A weighs 1000N and has a height of H1=3m and width W1=2m. Box B weighs 800N. the static friction coefficient between the boxes is uA=0.7 and the static friction coefficient between box B and the ramp is uB=0.5. Find the max allowable angle for the following instances where no motion occurs, box A and B remain stationary. 1) Box A slides, Box B remains stationary 2) Box A tips, Box B remains stationary 3) Box B slides, Box A remains stationary on block B
A 20 kg block is held in place on an incline plane as shown by a rope that passesover a frictionless pulley at B and then over a fixed cylinder at C where thecoefficient between the rope and the fixed cylinder is 0.2. Given an angle ofincline, A = 25°, if a force of P = 200 V is applied to the end of the rope,(a) Will the block move if the coefficient of static friction between the block and theinclined surface is M, = 0.56?(b)If impending motion exists, will the block tip or slip?
The weight of the motorcycle is 151 kg and the weight of the driver is 64 kg. Dimensions: l1 = 0,31 m and l2 = 0,23 m Determine the required frictional force.
Rod AB leans against the wall with a coefficient of static friction, μSB = 0.2. The contact surface at A is smooth (μSA = 0). Find the minimum force P necessary to prevent rod AB from sliding, given:WRod = 40 lbs, L1 = 7 ft, θ = 42 °.
A 100 N force acts as shown on a 30.6 kg block placed on an inclined plane. The coefficients of friction between the block and the plane are µs = 0.25 and µk = 0.2. Determine whether the block is in equilibrium and find the value of the friction force.
A 10 m long beam weights rests against the smooth wall as shown. The weight of the beamis 2 N. The coefficient of static friction between the beam and the ground is 1.4. Determine themaximum magnitude of force P that can be applied before the beam slides.
A load G1 is placed on the horizontal plane. A rope is attached to it, which is passed over a stationary pulley, and a load of weight G2 is attached to the other end of the rope. Determine the equilibrium position of the load G1 (length x) if the height x and the coefficient of friction µ are known.Note: The answer is x=h\tan alpha i want to understdan how this problem is fixed.
Having the coefficient of frictions (μs = 0.40 and μk = 0.30), Determine whether the block is in equilibrium(explain) and find the value of the magnitude and the direction of the actual force if:a) P = 230lbb) P = 350 lb