Answered: A 300-mm-diameter vitrified pipe is 100…

A 300-mm-diameter vitrified pipe is 100 m long. Using the Hazen-Williams formula, determine the discharge capacity of the pipe if the head loss is 2.54 m. Show a free body diagram

Fundamentals of Geotechnical Engineering (MindTap Course List)

5th Edition

ISBN:9781305635180

Author:Braja M. Das, Nagaratnam Sivakugan

Publisher:Braja M. Das, Nagaratnam Sivakugan

Chapter7: Seepage

Section: Chapter Questions

Problem 7.6P

See similar textbooks

Related questions

Q: The infiltration capacity in a basin is represented by Horton’s equation as fp = 4.0 + e-3.5t…

A: From the given infiltration capacity in a basin represented by Horton’s equation as fp = 4.0 +…

Q: ts to determine the permeability of an aquifer. The aquifer has a test well 300-mm in diameter with…

Q: Draw a flow net for the weir shown in the Figure. Calculate the rate of seepage under the weir in…

A: We have to draw a flow net for the weir shown in the Figure. Calculate the rate of seepage under the…

Q: Problem: Three pipes of different length and diameters connected in series as shown discharges 160…

Q: A hydraulic jump is designed to occur in a rectangular open channel. The ratio of the sequent water…

Q: The actual discharge through an orifice of diameter 30 mm is 24 liters/sec. The bead water over the…

A: Given data: Actual discharge (Q)=2.4 litres/secDiameter of orifice (d)=30 mmHead (h)=1.5 m

Q: Problem H: For Problem 28 to 29. In a constant head permeability test the following are given L= 250…

A: Determine head h and discharge velocity V?

Q: Liquid is flowing from one reservoir to another reservoir as shown in Figure through 10 cm diameter…

A: Diameter of pipe, D=10 cm=0.1 m Area of pipe, A=π4×D2=π4×0.12=0.007854 m2 Radius of pipe, R=0.05 m…

Q: Problem 7 A circular culvert under a highway is 2 m in diameter and is made of corrugated metal…

Q: eservoir A is at elevation 240m. From Reservoir A, a 450mm pipe, 600m long connects to point B at…

A: Question is based on the flow through reservoir's . Length , diameter, elevation and discharge of…

Q: A three reservoir problem shown in the figure with their corresponding length and diameter.…

A: L1= 1700m L2= 1900m L3= 3500m

Q: the head loss of the pipeline

Q: A hydraulic jump occurs in a closed circular conduit as shown in the figure. The conduit is…

Q: 3.1. Calculate head loss in a CI pipe of length L= 100 m, with discharge Q at entry node = 0.2 m/s,…

A: Given:- The length of the CI pipe = L = 100 m The discharge at entry node (Q) = 0.2 m3/s The…

Q: Problem 2: Fluid flows through a 20-mm diameter pipe, 150 m long at a Reynoids number of 1,750.…

Q: PROBLEM 3 Water flows in a 4-cm-diameter pipe at 20 m/s. The pipe divides into two pipes, one 2 cm…

Q: Two reservoirs are connected by a pipeline consisting of two pipes A and B with equal friction…

Q: Problem 1: Three pipes of different length and diameters connected in series as shown discharges 160…

A: We have…

Q: Problem 4. A water treatment plant has six settling tanks that operate in parallel (the flow gets…

Q: A tube well penetrates into an unconfined aquifer having a saturated depth of 80 m. When the…

A: Solution:

Q: ) Calculate the discharge from a tubewell of 20-cm diameter penetrating fully into a confined…

A: Given data in question Diameter of well 20 cm Thickness 20 m Permeability 40 m/day Drawdowns 3m and…

Q: % of the major loss.

A: Given data Length, L=2.5m=2.5×103 m=2500m Diameter, D=600mm=0.6m Friction factor, f=0.02 Minor…

Q: Two reservoirs are connected to each other with a pipe of length of 2 km and diameter 0.2 m.…

A: Given: Length, L = 2 km Diameter, d = 0.2 m Difference in water level, h = 8 m Friction factor, f =…

Q: Flow of a liquid in a smooth 3 cm pipe yields a head loss of 2 m per meter of pipe length when the…

A: Given- a pipe carrying a liquid with the mean velocity of 1m/s. Required- to find friction…

Q: A 6cm diameter horizontal water pipe expands to a 10cm diameter pipe. The average velocity and…

Q: 21) A water treatment plant treats 12000 m/d of raw water by using three rectangular clarifiers,…

A: Given, Flow= 12,000 m³/day We have 3 Rectangular Clarifiers. Each clarifier dimensions: 25m×5m×4m…

Q: Q2 Figure Q2 shows a cross section of a river at Sg. Melaka treatment plant. Using data in Table Q2,…

A: Solution by Velocity-Area method by Mean-Depth

Q: 1. COMPUTE THE VELOCITY AT A DISTANCE OF 20.5 m FROM THE FIRST POINT 2.COMPUTE THE DISCHARGE IN…

A: Since the question number to be solved is not specified, the solution for Question No.01 is as…

Q: An artesian well with a radius of 0.75 meters was constructed to pump water from a source with a…

Q: You are working as a trainee engineering in a company ABC, is the leading manufacturing company for…

A: Fig, 1.1 aDifference in head (H) = 20 mkent = 0.5kexit = 1Diameter of pipe (D) = 50 mmLength of…

Q: pipeline leads from one reservoir to another which has a water surface 10 m lower.For a discharge of…

A: Q = discharge = 1 m3s H = water difference between two reservoirs = loss of head = 10m we are…

Q: A 0.5 km long pipe of diameter 0.45 m is connecting togeth er two reservoirs. If the difference in…

A: Given: Length of pipe, L = 0.5 km = 500 m Diameter of pipe, d = 0.45 m Difference in water level of…

Q: Example 5.23 Two 30 cm wells completely penetrate an artesian aquifer of thickness 15 m and are…

Q: A spillway controls reservoir 4.6 hectares in area. The permanent crest is at elevation 75 m. Water…

A: Solution Given Data Area of reservoir A=4.6 hactare=4.6*104 m2= 46000 m2Permanent crest is at…

Q: In the model test of a spillway the dişcharge and velocity of flow over the model were 2 m'/s and…

A: Given: Discharge over model, Qm = 2 m3/s Velocity over model, vm = 1.5 m/s Scale ratio, Lr =36

Q: For the series/parallel pipes shown, the total head loss in the system is 25 m. Determine the…

A: Total head loss = 25m

Q: Situation 3: Three pipes of different lengths and diameters connected in series as shown discharge…

A: Given: The length of pipe 1 is 1800 m. The length of pipe 2 is 1500 m. The length of pipe 3 is 800…

Q: Two reservoirs are interconnected with a piping network as shown in Figure 3. Water is drawn off at…

A: The figure given is 2 reservoirs interconnected with a pipe network Head between two reservoirs is…

Q: Two reservoirs are connected by two pipelines as shown in Figure 5.1. The difference in the…

Q: From the figure shown, determine the flow in the open channel in cubic meter per second if the…

A: To determine the flow rate for given trapezoidal open channel. Given, Coefficient of discharge, Cd…

Q: For a pipe of diameter 1 m when running full, the hydraulic mean depth will be: O 0.75 m O 1.0 m O…

A: Given data- Pipe diameter D=1 mpipe is flowing in full conditionTo Find-The hydraulic mean depth R

Q: Three reservoirs are connected respectively with pipes 1, 2 and 3 joining at a common junction P.…

Q: The two reservoirs connected by a smooth pipe below contain water at 20 °C. Ignoring minor losses in…

Q: The discharge through a concrete pipe of 1 ft diameter and 3000 ft length is 1.0 cfs. What is the…

A: To Determine Head loss in the pipe, hL

Q: For a ditch drain shown in the figure below find discharge capacity in cumecs using Elliot's formula…

A: A particular form of chezy equation is called Elliot's formula. Given, ∆h= 20 cm/km

Q: A 30 cm diameter well completely penetrates a confined aquifer of permeability 45 m/day. The length…

Q: A 300-mm-diameter vitrified pipe is 100 m long. Using the Hazen-Williams formula, determine the…

A: Given 300-mm-diameter vitrified pipe Length = 100 m head loss is 2.54 m. To determine The…

Q: Water is flowing in a 100 mm diameter Mild Steel (MS) pipe of length 180 m as shown in the…

A: The study of kinematics of flow is limited to the factors that produce fluid motion rather than the…

Q: Water flows through a concrete pipe 3 ft in diameter between reservoir A and reservoir B. The…

A: Diameter of pipe(D)=3 ft Elevation of reservoir surface A=800 ft Elevation of reservoir surface…

Q: At Point A, in a pipeline carrying water (y=62.4 Ib/ft^3) the diameter is 4.0 ft, the pressure is 10…

Concept explainers

Time and time related variables in engineering

Time is the event progression starting from past to present and then, future statistically. The time-related variable is any particular value in relation to time to assess its changes on a specified (XY) plane.

Question

A 300-mm-diameter vitrified pipe is 100 m long. Using the Hazen-Williams formula, determine the discharge capacity of the pipe if the head loss is 2.54 m. Show a free body diagram

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Time and time related variables in engineering

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

Tank A has an elevation of 100 m and Tank B has an elevation of 160 m. Since Tank A is lower than B, engineers have installed a pump near A to transfer fluid to B. The discharge in the pipe is at 0.65 cubic meters per second and pipe has a length of 1 km. with a diameter of 0.6 meters. If Hazen williams coefficient is equal to 120, compute the head loss in the pipe.
A 1,200-mm diameter transmission pipe carries 126 l/s from an elevated storage tank with a water surface elevation of 540 m. Two kilometers from the tank, at an elevation of 434 m, a pressure meter reads 586 kPa. If there are no pumps between the tank and the meterlocation, what is the rate of head loss in the pipe? (Note: 1 kPa = 1,000 N/m2.)
A pipeline leads from one reservoir to another which has a water surface 10 m lower.For a discharge of 1.0 m^3/s, determine the head loss in meter. a.10 b.8 c.9 d.12
A pipe 800 m long connects two reservoirs whose level difference is 60 m. Find the discharge in pipe in Liters/sec, if diameter of pipe is 0.5 m. Take all losses into account. Assume f = 0.01
Oil (SG = 0.89), with a kinematic viscosity of 0.007 ft2/s, flows in a 3-in.-diameter pipe at 0.049 ft3/s. Determine the head loss per unit length of this flow.
The waste weir of a reservoir is 50m long. After a heavy downpour, the depth of water over the weir was 0.80 m and the flow over the weir lasted for 0.50 hours. Using Francis formula and assuming velocity approach negligible, compute the total discharge through the weir.
The discharge end of a 2.5km long distribution pipe is 15m below the surface of the reservoir. The pipe is 600mm in diameter and has a friction factor of 0.02. Compute the discharge of the pipe if minor loss is 10% of the major loss.
The total head loss in the pipe system shown in Fig. 2 is 15m. Assuming f=0.02 for all the pipes, determine the discharge (cu. m/sec) in: a) pipe 1 b) pipe 2 c) pipe 3
The infiltration capacity in a basin is represented by Horton’s equation as fp = 4.0 + e-3.5t Where fp is in cm/h and t is in hours. Assuming the infiltration to take place at capacity rate in a storm of 120 minutes duration, estimate the total depth of infiltration during the storm.
Two reservoirs are connected to each other with a pipe of length of 2 km and diameter 0.2 m. Determine the velocity of flow in the pipe taking in account the frictional, entry, and exit losses if the difference in level of water at both reservoirs is 8 m and the friction factor of pipe is 0.04.
Three pipes of 400 mm, 350 mm and 300 mm diameter are connected in series between two reservoirs with a difference in level of 12 m. The friction factors are 0.024, 0.021 and 0.019 respectively. The lengths are 200 m, 300 m and 250 m respectively. a) The flow in m^3/s in PIPE 3 is nearest to... b) What is the head loss in meters in pipe 3? c) Determine the length of an equivalent 350mm diameter pipe.
Three reservoirs are connected at a junction, P, as shown. Reservoir A, whose surface elevation is at 60.0 metersfrom a given datum, discharges water at a rate of Q1 to junction P. Reservoir B, whose surface elevation is at 20.0m, then receives water from the junction at a rate of Q2, while Reservoir C, whose surface elevation is at 0.0 m,then receives water from the same junction at a rate of Q3. The head loss as fluid travels through the pipe fromreservoir A to the junction is hL1. The head loss as the fluid travels from the junction to reservoir B is hL2 and thehead loss as the fluid travels from the junction to reservoir C is hL3. (a) Setup the continuity equation at the junction.(b) What is the total head loss, in meters (give the numeric value), as water travels from reservoir A to reservoir B?(c) Similarly, what is the total head loss, in meters (give the numeric value), as water travels from reservoir A toreservoir C?