A 500mm width square tied column with reinforcement on four faces has a gross steel ratio is 0.02 and the concrete cover from the column surface to the steel centroid is 100 mm. What is the nominal axial capacity of the column if subjected to biaxial bending where ex = ey = 250 mm.? Use fc' = 21 MPa and fy = 415 MPa, reciprocal load method, and the appropriate interaction

A 500mm width square tied column with reinforcement on four faces has a gross steel ratio is 0.02 and the concrete cover from the column surface to the steel centroid is 100 mm. What is the nominal axial capacity of the column if subjected to biaxial bending where ex = ey = 250 mm.? Use fc' = 21 MPa and fy = 415 MPa, reciprocal load method, and the appropriate interaction

Steel Design (Activate Learning with these NEW titles from Engineering!)

6th Edition

ISBN:9781337094740

Author:Segui, William T.

Publisher:Segui, William T.

Chapter9: Composite Construction

Section: Chapter Questions

Problem 9.1.3P

See similar textbooks

Similar questions

2. A distributed load of W N/m is applied over the entire length of a simply supported beam 4m long. The beam has a cross section shown. -200- 20 120 160 20 -160- a. Which of the following gives the value of "W" so that it will not exceed an allowable flexural stress of 10 MPa. b. Which of the following gives the value of "W" so that it will not exceed an allowable shearing stress of 0.80 MPa. c. Which of the following gives theh value of "W" so that the screws have a shear strength of 800 N and a pitch of 50 mm.
A) Determine the shape factor and the Fully Plastic Moment (Mp) for the shaded symmetrical hollow rectangular beam section shown below. Assume the yield stress Oy =275 N/mm². B) If two plates of width 250 mm and thickness equal to 't' mm is connected (fabricated) at top and bottom (one plate on each side) for the given section, then what is the improvement in the fully plastic moment(Mp) of the section. C) If this revised fabricated section is now rotated by 90 degrees, what is its effect on the shape factor of the section? 200 mm. 50 m 100 ma 400 t- 10mm Note Take the value the 't' as equal to the last two digits of your studentid. If the last two digits are zero then take timm
A) Determine the shape factor and the Fully Plastic Moment (Mp) for the shaded symmetrical hollow rectangular beam section shown below. Assume the yield stress Oy =275 N/mm². B) If two plates of width 250 mm and thickness equal to 't' mm is connected (fabricated) at top and bottom (one plate on each side) for the given section, then what is the improvement in the fully plastic moment(Mp) of the section. C) If this revised fabricated section is now rotated by 90 degrees, what is its effect on the shape factor of the section? 200 mm. -50 m 100 mm t- 10 400 Note Take the value the 't' as equal to-the last two digits of your student-id. If the-last two digits are zero then take taimm
A rectangular cantilever beam has a width of 300mm and an effective depth of 480mm. It is reinforced with 7-25mm bars. The beam is carrying a uniformly distributed dead load of 15kN/m. The compressive strength of the concrete is 21MPa and the yield strength of the steel is 415MPa. The magnitude of the Ultimate moment capacity is Blank 1kN.m.
A) Determine the shape factor and the Fully Plastic Moment (Mp) for the shaded symmetrical hollow rectangular beam section shown below. Assume the yield stress Oy =275 N/mm?. B) If two plates of width 250 mm and thickness equal to 't' mm is connected (fabricated) at top and bottom (one plate on each side) for the given section, then what is the improvement in the fully plastic moment(Mp) of the section. C) If this revised fabricated section is now rotated by 90 degrees, what is its effect on the shape factor of the section? 200 mm. -50 mt 100 mm 400 50m Note : Take the value the 't' as equal to the last two digits of your student id. If the last wo digits are zero then takes T=10mm ww 00T
A square hollow steel structure with a wall thickness of t1 = 10 mm is pin linked to two gusset plates with a thickness of t2 = 12 mm, which are welded to a base plate with a thickness of 12 mm and secured to a concrete base with 4-16 mm diameter anchor bolts. The pin has a diameter of 16 mm. P = 48 kN compressive load, 30 deg. P= 48 kN Stnt gusset plate fy=12 mm 0=30 10 m 12 mm 16 mm ø anchor bolt 4-16 mm p 1. Determine the bearing stress in MPa between the struct and the pin. 2. Calculate the pin's shear stress in MPa. 3. Determine the anchor's shear stress in MPa.
The beam shown has the following properties: concrete cover=40mm, ds= 10mm, f'c=21 MPa, and fy=280 MPa. Determine the ultimate moment capacity of the beam in kN-m. Determine also the type of failure and the beam condition (under-reinforced, over-reinforced or balanced condition) 250mm 5-ø16mm h =450mm 50mm
270 KN Collar 1. The round bar shown in the figure has steel, brass, and aluminum sections. Axial loads are applied at cross sections A, B, C, and D. If the allowable axial stresses are 125MPa in the steel, 70MPa in the brass, and 85MPa in the aluminum, determine the diameters required for each of the sections Assume that the allowable stresses are the same for tension (T) and compression (C). Include Solution and Free Body Diagram. Steel 245 KN -0.5m- Brass 100 mm 150 mm Bell crank 200 kN. -0.5 m C Aluminum D -0.5 m Support bracket- 25 mm 2. A vertical shaft is supported by a thrust collar and bearing plate as shown in the figure. Determine the maximum axial load that can be applied to the shaft if the average punching shear stress in the collar and the average bearing stress between the collar and the plate are limited to 75MPa and 100MPa, respectively. Include Solution and Free Body Diagram. 6 mm 225 KN Description Internal axial force on steel section, Rs= Internal axial force on…
A Rolled Steel Channel ISMC 400 @ 49.4 Kg/m is used as a column. The Column is Fixed at both ends. Determine the Design Compressive Strength of the section, if the length of the column is 700 cm. Take fy = 240 MPa
Determine the maximum safe service live load that the beam can carry if the service dead load is 12 kN/m including the beam weight and based on the capacity of the beam section shown. Use fc'=40 MPa and fy=415 MPa. Top bars are 6-32mm and bottom bars are 3-28 mm, center to center distance between the bar layers is 108mm. 7o mm 108 352 7o mm 300 mm
4. A tied column 300 x 350 mm as shown in the figure is reinforced with 6 pieces steel barshaving fy = 414 MPa and fc’ = 21 MPa as shown in the figure. The column is to resist a factoredload of 1000 kN and factored moment of 230 kNm. Using the interactiondiagram (from the reference textbook: Reinforced Concrete Design DIT Gillesania), determine the following:a. eccentricity, eb. steel ratioc. diameter of the steel bars
plz, solve all the parts of this problem. Use ACI code and Solve what you have been asked. Reinforced Concrete Design-1 A fixed ended beam with span length of 24′ and cross-section of 15ʺ x 24ʺ is subjected to uniformly distributed load is shown in figure 1. Unform service dead load is 1k/ft and uniform service live load is 1.4 k/ft. Taking ?c = 3?si and ?y = 40???, a) Analyze the beam for flexure only. b) Calculate the amount of reinforcement for the given demand and check for ductility requirements. c) Detail the reinforcement using #6 bar only, and also curtail the steel ensuring development length requirements. d) Show all your calculations in the form of neat and clean drafting. Note: Your drafting must include dimensional details, reinforcement details in both longitudinal and sectional views, and cut off locations of steel.