A 6.00-kg block is in contact with a 4.00-kg block on a rough surface as shown in the figure. Total friction force acts on the blocks is 10 N. The 6.00-kg block is being pushed by a horizontal 20.0-N force as shown. What is the magnitude of the force that the 6.00-kg block exerts on the 4.00-kg block? 20.0 N 77 6.00 kg 4.00 kg

A 6.00-kg block is in contact with a 4.00-kg block on a rough surface as shown in the figure. Total friction force acts on the blocks is 10 N. The 6.00-kg block is being pushed by a horizontal 20.0-N force as shown. What is the magnitude of the force that the 6.00-kg block exerts on the 4.00-kg block? 20.0 N 77 6.00 kg 4.00 kg

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A line is recorded as 472.90 m long. It is measured with a 0.65 kg tape which is 30.005 m long at 20 °C under a 50 N pull supported at both ends. During measurement, the temperature is 5 °C and the tape is suspended under a 75 N pull. The line is measured on 3% grade. E = 200 GPa, cross-sectional area of the tape is 3 mm2 and the coefficient of linear expansion is 0.0000116 m/°C. a. Compute the actual length of tape during measurement. b. Compute the total error to be corrected for the inclined distance. c. What is the true horizontal distance?
PROBLEM 2.78 A vibration isolation unit consists of two blocks of hard rubber bonded to plate AB and to rigid supports as shown. For the type and grade of rubber used r =1.54 MPa and G=12.6 MPa. Knowing that a centric vertical force of magnitude P=13 kN must cause a 2.5-mm vertical deflection of the plate AB, determine the smallest allowable dimensions a and b of the block. 75 mm bnin = 56.3 mm = 20.5 mm a min
Determine the minimum diameter of a solid bar which is required to transmit a torque of 40 kNm if the yield stress of the material of the bar is 120 N/mm?. Ans. 119.2 mm.
The beam shown is hinged at one end. It is supported by two steel rods of equal length of 1.5m. Before the load is applied, the beam hangs level. Use E 200, 000MPa and a = 11.7- m C" Neglect bending of the beam. A=640mm2 A=320mm2 A C D 1.2m 0.8 m 1.2 m 54KN What is the stress of rod B if there is no change in temperature in MPa?
1. *A propped cantilever has a 2m overhang. The beam has a load of 2W applied half way between the fixed support and the roller support and a load of W applied at the free end. What is the minimum value of W that will cause the beam to collapse? The beam has the cross-section shown below. The yield stress is 300 MPa. 75 mm 15 mm 300 mm 2W C D 15 mm 250 mm 15 mm, 2m B + 2m 2m
Determine whether the block shown is in equilibrium and find the magnitude and direction of the friction force when P = 100lb. 50 lb H, = 0.40 Hi = 0.30 40° 30° O Block is in Equilibrium, F-43.032 Ib, 30 deg. with the Harizantal Axis O Block is in Equilibrium, F-32.274 b, 40 deg. with the Harizontal Axis O Block is not in Equilibrium, F-32.274 lb, 30 deg. with the Horizontal Axis O Block is in Equilibrium, F-32.274 b, 30 deg. with the Horizontal Avis O Block is not in Equilibrium, F-43.032 lb, 30 deg, with the Horizontal Axis
A line is recorded as 472.90 m long. It is measured with a 0.65 kg tape which is 30.005 m long at 20oC under a 50 N pull supported in both ends. During measurement, the temperature is 5oC and the tape is measured under a 75 N pull. The line is measured on 3% grade. E = 200 GPa, cross sectional area of tape is 3 mm2 and the coefficient of linear expansion is 0.0000116 m/oC Compute the actual length of tape during measurement Compute the total error to be corrected for the inclined distance What is the horizontal distance?
A 500 N block is resting on an inclined plane. See figure below. coefficient of static friction, 0.3, coefficient of kinetic friction, µk 0.2 1. Find the minimum value of P necessary to have an impending motion if 0 = 30°. W 2. Find the maximum value of P to ils = 0.3 necessary have an impending motion if 0 = 30°. %3D = 0.2 3. Find the value P that will still make the block in equilibrium condition.
2. Consider a square bar 30 mm on side and 2.5 m long, having a material yield point 254 (in MPa). An applied axial load gradually builds up from zero to a value such that the elongation of the bar is 25 mm. Determine the permanent elongation of the bar. o = 3 oy, of = %3D 0.60y . 0.008 0.010 0.005
2. A rectangular piece of wood, 50mm by 100mm in cross section, is used as a compression block as shown in the figure. Determine the normal stress and shear stress in the plane A-A. | 60 kN 20 A 100mm
1. An axial compressive load of 50 tons is applied to a metal bar of square section 2 in. by 2 in. The contraction on an 8-in gauge length is found to be 0.022 in. and the increase in thickness 0.0018in. Find the value of Young's modulus and Poisson's ratio. If in addition to the axial load of 50 tons a uniform lateral pressure of 5 tons/in² is applied to the two opposite sides of the bar in both directions, find the contraction on the 8-in gauge length and the change in thickness.
2. The block of weight W2 is being held in its position by two cylindrical rollers resting on inclined surfaces. All contact surfaces have a coefficient of static friction, us = 0.36. Wi is 380 KN. Ms Ms W, W, 1 60 W2 a. What maximum value of W2 it can be before slipping of the block happens? b. Determine the normal force reaction against the inclined surfaces.