A 60° bend occurs in a water pipeline that reduces from 600 mm diameter to 300 mm diameter at the bend (inside bend angle 120). If the gauge pressure at the inlet is172 KPa, determine the magnitude ad angle of the thrust on the bend when the flow is 0.85 m/s. Hint: start by calculating the initial and final velocities, then the finalpressure. Next, analyze the pressure and momentum forces in the x and y planes.

Given data: Inlet diameter (di) = 600 mm Outlet diameter (do) = 300 mm Gauge pressure at the inlet =…

Answered: A 60° bend occurs in a water pipeline…

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A 3-cm-diameter horizontal pipe attached to a surface makes a 90° turn to a vertical upward direction before the water is discharged at a velocity of 6 m/s. The horizontal section is 5 m long and the vertical section is 4 m long. Neglecting the mass of the pipe and considering the weight of the water contained in the pipe, the bending moment acting on the base of the pipe on the wall is (a) 11.9 N·m (b) 46.7 N·m (c) 127 N·m (d) 104 N·m (e) 74.8 N·m
There is a conical plug at the bottom of the pressure tank as seen in the figure. The air pressure is 50 kPa and the specific gravity of the fluid in the tank is 27 kN/m3 'kind. remaining in the tank Determine the direction and magnitude of the force acting on the cone curve surface (h1=1 m, h2=3 m, ɵ=60o )
The water flows from the pipe shown in the figure with a flow rate of 0.025 m3 / s and emerges into the atmosphere as a free jet. Flow is frictionless and gravity effects are negligible. Since the pressure in the section (1) is 150kpa, find the x and y components of the force required to hold the pipe in place. [rsu = 999 kg / m3]
A cylinder weighing 400 lb is held against a smooth incline by means of the weightless rod AB in FIig. P-309. Determine the forces P and N exerted on the cylinder by the rod and the incline respectively.
Determine the magnitude of the horizontal reaction (N) at A if P = 254 N and Q = 2395 N. Let x = 2.48 m, y = 2.5 m, and z = 2.05 m. Round off only on the final answer expressed in 3 decimal places. Instead of units, indicate the direction of the horizontal reaction at A: use R if to the right and L if to the left.
An open horizontal tank 2 m high, 2 m wide and 4m. long is full of water. a) How much water is spilled out when the tank is accelerated horizontally at 2.45 misec in a direction parallel with its longest side? b.) What is the porce acting on the side with the greatest depth? c.) Compute the required accelerating force.
An open tank 1.82m square contains 1m of water. It is translated horizontally to the right at an acceleration of 3m/s2. a) How high should the tank be such that no water will be spilled? b) If the acceleration is now 5m/s2 and the height of the vessel is the answer in (a), how much water will be spilled? c) If the vessel is initially closed at the top and accelerated to the right at 5m/s2, what will be the hydrostatic force acting on the left side of the vessel?
An open rectangular tank moves upward along a 30o-incline as shown in the figure. What is the slope (tanθ) of the lines of constant pressure inside the tank?
Consider the steady open channel flow of water in the smooth constriction shown in plan view in Figure P10.46. At position 1, the depth is Y1, the width is B1 and the Froude number F1 = 4. A similar notation is used at positions 2, 3 and 4. A hydraulic jump is observed just downstream of position 2 where the Froude number F2 = 2. You may assume one-dimensional flow. (a) Find Y2, the depth at position 2, in terms of Y1. (b) Find Y3, the depth just downstream of the hydraulic jump, in terms of Y1. (c) Find F3, the Froude number just downstream of the hydraulic jump. (d) Find F4, the Froude number at the exit, given that Y3/Y4 = 1.2. (e) Find B4/B1.
There is X=5m high water on the left side of a 3.5 m wide vertical cover sitting on the hinge shown in the figure. On the right, a water jet with a cross-sectional area of A=1100 cm2 hits the cover. a) Determine the horizontal hydrostatic pressure force acting on the cover and the vertical distance of the impact point to the hinge. b) What should be the Q flow rate of the water jet so that the lid remains vertical? (gravity forces will be neglected)
Two parallel plates are separated by a 0.22 mm space filled with a fluid (sp gravity = 0.964) of kinematic viscosity 5.6 × 104 m /. The lower plate is stationary, and the upper plate having a 2x2 m2 area moves at a velocity of 6.6 m/sec. Estimate the shear force on the underside of the upper plate.
.Determine the minimum force P that will cause impending motion of the block shown in Figure P7–12. Will the block tip or slide? (If tipping occurs about point A, both the normal force N and the friction force F will be acting through point A.)

SEE MORE QUESTIONS

Recommended textbooks for you

Structural Analysis

Civil Engineering

ISBN:

9781337630931

Author:

KASSIMALI, Aslam.

Publisher:

Cengage,

Structural Analysis (10th Edition)

Civil Engineering

ISBN:

9780134610672

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Principles of Foundation Engineering (MindTap Cou…

Civil Engineering

ISBN:

9781337705028

Author:

Braja M. Das, Nagaratnam Sivakugan

Publisher:

Cengage Learning

Structural Analysis

Civil Engineering

ISBN:

9781337630931

Author:

KASSIMALI, Aslam.

Publisher:

Cengage,

Structural Analysis (10th Edition)

Civil Engineering

ISBN:

9780134610672

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Principles of Foundation Engineering (MindTap Cou…

Civil Engineering

ISBN:

9781337705028

Author:

Braja M. Das, Nagaratnam Sivakugan

Publisher:

Cengage Learning

Fundamentals of Structural Analysis

Civil Engineering

ISBN:

9780073398006

Author:

Kenneth M. Leet Emeritus, Chia-Ming Uang, Joel Lanning

Publisher:

McGraw-Hill Education

Sustainable Energy

Civil Engineering

ISBN:

9781337551663

Author:

DUNLAP, Richard A.

Publisher:

Cengage,

Traffic and Highway Engineering

Civil Engineering

ISBN:

9781305156241

Author:

Garber, Nicholas J.

Publisher:

Cengage Learning

SEE MORE TEXTBOOKS