A 60-Hz, single-phase power line and a telephone line are parallel to each other as shown in the following figure. The telephone line is symmetrically positioned directly below phase b. The power line carries an rms current of 226 A. Assume zero current flows in the ungrounded telephone wires. Find the magnitude of the voltage per Km induced in the telephone line. 5 m 3 m d O 2*m O

A 60-Hz, single-phase power line and a telephone line are parallel to each other as shown in the following figure. The telephone line is symmetrically positioned directly below phase b. The power line carries an rms current of 226 A. Assume zero current flows in the ungrounded telephone wires. Find the magnitude of the voltage per Km induced in the telephone line. 5 m 3 m d O 2*m O

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter2: Fundamentals

Section: Chapter Questions

Problem 2.13MCQ

See similar textbooks

Similar questions

The instantaneous voltage across a circuit element is v(t)=400sin(t+30)volts, and the instantaneous current entering the positive terminal of the circuit element is i(t)=100cos(t+10)A. For both the current and voltage, determine (a) the maximum value, (b) the rms value, and (C) the phasor expression, using cos(t) as the reference.
Under balanced operating conditions, consider the three-phase complex power delivered by the three-phase source to the three-phase load. Match the following expressions, those on the left to those on the right. (i) Realpower, P3 (a) (3VLLIL)VA (ii) Reactive power, Q3 (b) (3VLLILsin)var (iii) Total apparent power, S3 (c) (3VLLILcos)W (iv) Complex power, S3 (d) P3+jQ3 Note that VLL is the rms line-to-line voltage, IL is the rms line current, and is the power-factor angle.
Let a series RLC network be connected to a source voltage V, drawing a current I. (a) In terms of the load impedance Z=ZZ, find expressions for P and Q, from complex power considerations. (b) Express p(t) in terms of P and Q, by choosing i(t)=2Icost. (c) For the case of Z=R+jL+1/jC, interpret the result of part (b) in terms of P,QL, and Qc. In particular, if 2LC=1, when the inductive and capacitive reactances cancel, comment on what happens.
An AC generator having an internal resistance of 2 ?? is connected to an LCR circuit in series as shown in the figure. If the generator supplies an electromotive force, ? = 282 ??? (100??) volt, calculate:a) the impedance of the circuitb) the rms value of the current in the circuitc) the voltage drop across L, C and R
Discuss the significance of power generation, transmission, and distribution in the context of a reliable and efficient power supply. What are the challenges associated with each of these phases?
In U.S. residences, electrical power is generally utilized at a nominal voltage of 120 V rms. What problems would become pronounced if the power distribution system and household appliances had been designed for a lower voltage (say, 12 V rms)? For a higher voltage (say, 12 kV)?
In the circuit given on the side Ra=Rb=Rc=Basic frequency of 13 Ohm loadsit is powered by an AC voltage of f= 60 Hz. Power derived from the sourceits value was measured as Pk=9372.12 Watts. Each switchingthe element is triggered in such a way that it will be at 180 degrees.The DC bus voltage (E=?) and the effective value of the ic phase current(ic rms=?) calculate.
Explain the concept of load flow analysis in power systems. How does it help in determining the steady-state operating conditions of a power grid, and what are its limitations?
For the maximum average power transfer in the circuit shown in Figure 2, use the impedance ZLand ZLFind the value of the maximum average power transferred to ? (Can you write the steps in detail in sentences?)
a question by considering the annual load time curve for an electric station as a straight line from 20mw to 3mw, and to cover these loads, then operate three generating units, the first and second, each with a capacity of 10mw, while the third has a capacity of 5mw, and illustrate the load time curve by drawing, then find: 1- the total capacity of the station 2- the maximum demand 3- capacitance coefficient 4- pregnancy coefficient 5 utilizatio
a question by considering the annual load time curve for an electric station as a straight line from 20mw to 3mw, and to cover these loads, then operate three generating units, the first and second, each with a capacity of 10mw, while the third has a capacity of 5mw, and illustrate the load time curve by drawing, then find: 1- the total capacity of the station 2- the maximum demand 3- capacitance coefficient 4- pregnancy coefficient 5 utilization factor
1. Write down a formula for the three-phase power factor, assuming perfectly sinusoidal and symmetrical conditions, using line-line voltage measurements. 2. Write down a formula that relates three-phase apparent power to active and reactive power. 3. Draw a graph that depict single-phase waveforms for a purely sinusoidal 50 Hz voltage and a lagging current.