(a) A 30 kW, 150 v, DC shunt generator has armature resistance of 0.09 Q and field resistance of 50 O. Consider the DC machine principle of operation to determine the total armature power developed when the generator working as: (i) Generator delivering 30kW at its output terminals. (ii) Motor taking 30 kW from the input terminals.

(a) A 30 kW, 150 v, DC shunt generator has armature resistance of 0.09 Q and field resistance of 50 O. Consider the DC machine principle of operation to determine the total armature power developed when the generator working as: (i) Generator delivering 30kW at its output terminals. (ii) Motor taking 30 kW from the input terminals.

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Of a shunt excited DC generator, Excitation winding internal resistance Rf = 2.5 Ω Armature winding internal resistance Ra = 0.5 Ω A rheostat has been placed in the excitation circuit to keep the machine's end voltage constant at Va = 30 V. Machine Voltage magnetization induced in the armature while operating at n = 1400 rpm at If = 7 A excitation current It is determined as Ea = 30 V from its characteristic. According to this, a) With peak voltage Va = 30 V, excitation current If = 7 A, power supplied to the load when the speed n = 1400 rpm What is the resistance of the rheostat? b) Spindle revolutions are reduced to n = 1000 rpm. In this case Va = 30 V and Ea = 37 V constant What value should the rheostat be adjusted to keep it? Calculate the power given to the load in this new case.
A 20KW, 440V, short shunt compound dc generator has full load efficiency of 87%. If the resistance of the armature and interpoles is 0.4ohm and that of the series and shunt fields 0.25ohm and 240ohms respectively, calculate the combined bearing friction, windage and core loss of the machine A 10 kW 250 volts self-excited generator, when delivering rated load, has an armature-circuit voltage drop of 5% of the terminal voltage and a shunt field current equal to 5% of the rated load current. The resistance of the armature is 0.02 ohm. Calculate the voltage generated and power output.
A 110V shunt generator has a full load current of 100A, shunt field resistance of 55 ohms and constant losses of 500W. If full load efficiency is 88%, find the armature resistance. Assuming voltage to be constant at 110V, calculate the efficiency at half load. Find the load current.
- A separately excited 4 - pole, 900 rpm wave wound dc generator has an induced emf of 240V at rated speed and rated field current. When connected to a load, the terminal voltage is observed to be 200V. If the armature resistance is 0.2 Ω and the flux per pole is 10 m Wb, compute the armature current and the number of conductors
A separately excited DC generator has rated terminal voltage and full load armature current of 220v and 42+16. A respectively and rated speed of 1650 rpm. The generator armature resistance Ra =0.3 π and field resistance Rf =100+16 π and field voltage of 150v. Calculate: a) The induced emf and torque at full load. b) The emf at rated speed when the field voltage is changed to 110 v.
A short-shunt compound DC generator supplies a current of 100 A at 220 V. If the resistance of the shunt field is 50 ohms, of the series field 0.025 ohms, of the armature 0.05 ohm, the total brush drop is 2 V and the iron and friction losses amount to 1 kW, determine the following: The armature current, Amp The generated voltage, V The copper losses, W The output power of the prime mover, kW The generator efficiency, %
6/ What are the parameters required for the internal characteristics of the DC Generator? a. Terminal voltage (V) and Field current (If) b. Generated EMF (Eg) and Armature current (Ia) c. Terminal voltage (V) and load current (IL) d. Generated EMF (Eg) and Load Current (IL)
A 25kW, 250V DC shunt machine has an armature and field resistances of 0.060 and 1000respectively. Determine the total armature power developed when working () as generator delivering25kW output and (ii) as motor taking 25kW input
A shunt Generator terminal voltage is 243.5 V and the load current is 4.5 Amps. Its Armature resistance is 1.1 Ohms. What is the Generated emf of the DC Generator, consider the shunt field current as 0 Amps?
A separately excited generator,when running at 1000rpm supplied 200A at 125V. What will be the load current when the speed drops to 800rpm if current is unchanged? Given the armature resistance of 0.04 ohms and brush drop of 2V.
A shunt generator has a field resistance of 60 ohms. When the generator driven 6KW, the terminal vtage is 125 Volts, while the generated emf is 133V. Determine a.) The armature resistance, and b.) The generated emf when the output is 2KW at terminal voltage of 135 V.
7. Increasing the length of the air gap of DC machine reduces the Armature reaction effect. Select one: True False