*a, b, c, and d are major nodes · An 18V-source and 40-resistor are in series between the nodes a and b wherein the positive terminal of the source is connected to a. - Two resistors with values 50 and 70 are in series between the nodes b and c. ·A 12V-source is in between nodes c and d wherein its positive terminal is connected to node d. · A 30-resistor is in between nodes d and a. · An 80-resistor is in between nodes b and d. ·A series connected resistor and voltage source, with values 20 and 24V respectively, are between nodes and c. The positive terminal of the source is connected to node a.

*a, b, c, and d are major nodes · An 18V-source and 40-resistor are in series between the nodes a and b wherein the positive terminal of the source is connected to a. - Two resistors with values 50 and 70 are in series between the nodes b and c. ·A 12V-source is in between nodes c and d wherein its positive terminal is connected to node d. · A 30-resistor is in between nodes d and a. · An 80-resistor is in between nodes b and d. ·A series connected resistor and voltage source, with values 20 and 24V respectively, are between nodes and c. The positive terminal of the source is connected to node a.

Delmar's Standard Textbook Of Electricity

7th Edition

ISBN:9781337900348

Author:Stephen L. Herman

Publisher:Stephen L. Herman

Chapter8: Combination Circuits

Section: Chapter Questions

Problem 1PA: A circuit contains a 1000- and a 300- resistor connected in series with each other. The total...

See similar textbooks

Similar questions

A circuit contains a 1000- and a 300- resistor connected in series with each other. The total circuit resistance must be reduced to a value of 1150 . Using standard resistance values of 5% resistors discussed in Unit 5, explain how to change the present resistance value to the value desired.
A voltage divider of 50 ohms is connected across a 100 V DC source. A load resistance of 10 ohms is connected across a tap in the potential divider and the negative of the source. If a current of 4 A flows towards the load, what is the current supplied by the source? (Remember, a voltage divider is a network of resistors that are connected in series the purpose of which is to divide a voltage into each of the resistors.) Show complete solution.
Answer the following questions related to a series/parallel combinational circuit configured as follows: R1 is in series with the source and also in series with the parallel combination of R2 and R3. The circuit’s voltage is +24VDC, R1= 4.5kΩ, R2=30kΩ, and R3=10kΩ. What is the Thevenin’s voltage (ETH) for the circuit described above if a load resistor of 20kΩ is placed in parallel with R2 and R3?
Two resistors A and B are connected in series with a 220-V DC source. a voltmeter with an internal resistance of 10k Ohms is connected across resistor A, the instrument reads 100V and when connected across resistor B, it reads 80V. Find the value of the two resistances in series. please show complete solution.
A coil of resistance 16 ohm is connected in parallel with a coil of resistance R₁. This combination is then connected in series with resistances R2 and R3. The whole circuit is then connected to 220 V D.C. supply. What must be the value of R1 so that R₂ and R3 shall dissipate 800 W and 600 W respectively, with 10 A passing through them?
For the following circuit: Calculate the Thévenin equivalent between B and A by the test source method and draw the resulting circuit. Draw the Thévenin equivalent if all resistors are In this case, how much will the current through a resistor connected between A and B be worth? Assume that R1 = R2 = R, R3 = R-ΔR and R4 = R+ΔR. How much are t h e Thévenin voltage and resistance worth? Is the Thévenin voltage linear with respect to ΔR?
a. Calculate the voltages across each resistor in the circuit shown and record all results in Table below under the Calculated row. Note that Vsource is 5 V. b. Compute for the sum -Vsource+V330+V1k around loop 1, V470+V2.2k-V1k around loop 2, and -Vsource+V330+V470+V2.2k around loop 3 and record the result under the Calculated row.
find voltages V1 and V4 (in terms of Vs and the resistances) using each of the following methods use voltage division and series/parallel combination of resistors use mesh analysis to determine I1 and I2, then V1=R1I1 and V4=R4I2 use nodal analysis to find Va,Vb and Vc, then V1=Va-Vb and V4=Vc
Two batteries, A and B, are connected in parallel and an 80 ohm resistor is connected across thebattery terminals. The e.m.f. and the internal resistance of battery A are l00V and 5 ohm respectively,and the corresponding values for battery B are 95V and 3 ohm respectively. Find (a) the value anddirection of the current in each battery and (b) the terminal voltage
The circuit shown in figure b) is the Thévenin equivalent circuit of the circuit shown in figure a). Determine the value of the open circuit voltage, vcab, and the Thévenin resistance, RTH Answer: vcab= 2v and RTH= 4 Ohms
Given that Short circuit current - 5.52 A Open circuit voltage - 45.1 V Current at MPP - 5.19 A Voltage at MPP - 36.6 V Power at MPP - 190 W Number of PV cells and area of each cell - 72 cells (125mm × 125mm) Efficiency of PV module and the area of module - 14.9% efficiency (1581mm × 809mm × 35mm) Twelve (12) modules are configured into 4 strings of 3 modules in series. Two strings areput in parallel and then connected in series with another set of two strings in parallel. Determine the power at MPP under standard conditions.
How much resistance R1 must be added in series with a 400 Ω R2 to limit the current to 0.25 A with 120 V applied? Which statement is correct about a parallel circuit? a)The source voltage is equivalent to the voltage across each load. b)The total current is equivalent to the sum of the branch currents c)The total resistance is equivalent to the sum of the reciprocal of each load resistance. d)The source voltage is equivalent to the sum of the individual voltage drops. A heater element rated for 1000 watts and 120 volts is operated from a 100-volt source. As a result, its:a)resistance will decrease.b)resistance will remain the same.c)wattage will increase.d)current will increase.